COMMON Command Line Interface

Reference Manual

Revision Date: 09.11.03

9033603-03
 NOTICE

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document
and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any
such changes have been made.
The hardware, firmware, or software described in this document is subject to change without notice.
IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR
RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS
NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road
Andover, MA 01810

 2003 Enterasys Networks, Inc. All rights reserved.

Printed in the United States of America.

Part Number: 9033603-03 September 2003

ENTERASYS NETWORKS, NETSIGHT, LANVIEW, and any logos associated therewith, are trademarks or
registered trademarks of Enterasys Networks, Inc. in the United States and other countries.
All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.
 ENTERASYS NETWORKS, INC.
PROGRAM LICENSE AGREEMENT
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc. on behalf of itself
and its Affiliates (as hereinafter defined) (“Enterasys”) that sets forth Your rights and obligations with respect to the Enterasys
software program (including any accompanying documentation, hardware or media) (“Program”) in the package and prevails
over any additional, conflicting or inconsistent terms and conditions appearing on any purchase order or other document
submitted by You. “Affiliate” means any person, partnership, corporation, limited liability company, or other form of
enterprise that directly or indirectly through one or more intermediaries, controls, or is controlled by, or is under common
control with the party specified. This Agreement constitutes the entire understanding between the parties, and supersedes all
prior discussions, representations, understandings or agreements, whether oral or in writing, between the parties with respect
to the subject matter of this Agreement. The Program may be contained in firmware, chips or other media.
BY INSTALLING OR OTHERWISE USING THE PROGRAM, YOU REPRESENT THAT YOU ARE AUTHORIZED TO
ACCEPT THESE TERMS ON BEHALF OF THE END USER (IF THE END USER IS AN ENTITY ON WHOSE BEHALF
YOU ARE AUTHORIZED TO ACT, “YOU” AND “YOUR” SHALL BE DEEMED TO REFER TO SUCH ENTITY) AND
THAT YOU AGREE THAT YOU ARE BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES,
AMONG OTHER PROVISIONS, THE LICENSE, THE DISCLAIMER OF WARRANTY AND THE LIMITATION OF
LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT OR ARE NOT AUTHORIZED TO
ENTER INTO THIS AGREEMENT, ENTERASYS IS UNWILLING TO LICENSE THE PROGRAM TO YOU AND YOU
AGREE TO RETURN THE UNOPENED PRODUCT TO ENTERASYS OR YOUR DEALER, IF ANY, WITHIN TEN (10)
DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT ENTERASYS NETWORKS, LEGAL
DEPARTMENT AT (978) 684-1000.
You and Enterasys agree as follows:
1. LICENSE. You have the non-exclusive and non-transferable right to use only the one (1) copy of the Program provided
in this package subject to the terms and conditions of this Agreement.
2. RESTRICTIONS. Except as otherwise authorized in writing by Enterasys, You may not, nor may You permit any third
party to:
(i) Reverse engineer, decompile, disassemble or modify the Program, in whole or in part, including for reasons of error
correction or interoperability, except to the extent expressly permitted by applicable law and to the extent the parties
shall not be permitted by that applicable law, such rights are expressly excluded. Information necessary to achieve
interoperability or correct errors is available from Enterasys upon request and upon payment of Enterasys’
applicable fee.
(ii) Incorporate the Program, in whole or in part, in any other product or create derivative works based on the Program,
in whole or in part.
(iii) Publish, disclose, copy, reproduce or transmit the Program, in whole or in part.
(iv) Assign, sell, license, sublicense, rent, lease, encumber by way of security interest, pledge or otherwise transfer the
Program, in whole or in part.
(v) Remove any copyright, trademark, proprietary rights, disclaimer or warning notice included on or embedded in any
part of the Program.
3. APPLICABLE LAW. This Agreement shall be interpreted and governed under the laws and in the state and federal
courts of the Commonwealth of Massachusetts without regard to its conflicts of laws provisions. You accept the personal
jurisdiction and venue of the Commonwealth of Massachusetts courts. None of the 1980 United Nations Convention on
Contracts for the International Sale of Goods, the United Nations Convention on the Limitation Period in the International Sale
of Goods, and the Uniform Computer Information Transactions Act shall apply to this Agreement.
4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of
the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical
products to certain countries, unless a license to export the Program is obtained from the U.S. Government or an exception
from obtaining such license may be relied upon by the exporting party.

Enterasys X-Pedition Common Command Line Interface Reference Manual iii

 If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export
Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the Program for
civil end uses only and not for military purposes.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export
Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree
not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country in Country
Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China, Romania, Russia,
Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be designated by the United
States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct product of the Program or the
technology, if such foreign produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant or any major component of a plant, export to
Country Groups D:1 or E:2 the direct product of the plant or a major component thereof, if such foreign produced direct
product is subject to national security controls as identified on the U.S. Commerce Control List or is subject to State
Department controls under the U.S. Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Program (i) was developed solely at
private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section
52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in all
respects is proprietary data belonging to Enterasys and/or its suppliers. For Department of Defense units, the Program is
considered commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and use,
duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. DISCLAIMER OF WARRANTY. EXCEPT FOR THOSE WARRANTIES EXPRESSLY PROVIDED TO YOU IN
WRITING BY ENTERASYS, ENTERASYS DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON- INFRINGEMENT WITH RESPECT TO THE
PROGRAM. IF IMPLIED WARRANTIES MAY NOT BE DISCLAIMED BY APPLICABLE LAW, THEN ANY IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THIRTY (30) DAYS AFTER DELIVERY OF THE PROGRAM TO
YOU.
7. LIMITATION OF LIABILITY. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY
DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,
PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
THIS FOREGOING LIMITATION SHALL APPLY REGARDLESS OF THE CAUSE OF ACTION UNDER WHICH
DAMAGES ARE SOUGHT.
THE CUMULATIVE LIABILITY OF ENTERASYS TO YOU FOR ALL CLAIMS RELATING TO THE PROGRAM, IN
CONTRACT, TORT OR OTHERWISE, SHALL NOT EXCEED THE TOTAL AMOUNT OF FEES PAID TO ENTERASYS
BY YOU FOR THE RIGHTS GRANTED HEREIN.
8. AUDIT RIGHTS. You hereby acknowledge that the intellectual property rights associated with the Program are of
critical value to Enterasys and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i)
license fees due and paid, and (ii) the use, copying and deployment of the Program. You also grant to Enterasys and its
authorized representatives, upon reasonable notice, the right to audit and examine during Your normal business hours, Your
books, records, accounts and hardware devices upon which the Program may be deployed to verify compliance with this
Agreement, including the verification of the license fees due and paid Enterasys and the use, copying and deployment of the
Program. Enterasys’ right of examination shall be exercised reasonably, in good faith and in a manner calculated to not
unreasonably interfere with Your business. In the event such audit discovers non-compliance with this Agreement, including
copies of the Program made, used or deployed in breach of this Agreement, You shall promptly pay to Enterasys the
appropriate license fees. Enterasys reserves the right, to be exercised in its sole discretion and without prior notice, to terminate
this license, effective immediately, for failure to comply with this Agreement. Upon any such termination, You shall
immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program.

iv Enterasys X-Pedition Common Command Line Interface Reference Manual

9. OWNERSHIP. This is a license agreement and not an agreement for sale. You acknowledge and agree that the Program
constitutes trade secrets and/or copyrighted material of Enterasys and/or its suppliers. You agree to implement reasonable
security measures to protect such trade secrets and copyrighted material. All right, title and interest in and to the Program shall
remain with Enterasys and/or its suppliers. All rights not specifically granted to You shall be reserved to Enterasys.
10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may
cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be
entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies
available at law.
11. ASSIGNMENT. You may not assign, transfer or sublicense this Agreement or any of Your rights or obligations under
this Agreement, except that You may assign this Agreement to any person or entity which acquires substantially all of Your
stock or assets. Enterasys may assign this Agreement in its sole discretion. This Agreement shall be binding upon and inure to
the benefit of the parties, their legal representatives, permitted transferees, successors and assigns as permitted by this
Agreement. Any attempted assignment, transfer or sublicense in violation of the terms of this Agreement shall be void and a
breach of this Agreement.
12. WAIVER. A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing
and will not be construed as a waiver of any subsequent breach of such term or condition. Enterasys’ failure to enforce a term
upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion.
13. SEVERABILITY. In the event any provision of this Agreement is found to be invalid, illegal or unenforceable, the
validity, legality and enforceability of any of the remaining provisions shall not in any way be affected or impaired thereby,
and that provision shall be reformed, construed and enforced to the maximum extent permissible. Any such invalidity, illegality
or unenforceability in any jurisdiction shall not invalidate or render illegal or unenforceable such provision in any other
jurisdiction.
14. TERMINATION. Enterasys may terminate this Agreement immediately upon Your breach of any of the terms and
conditions of this Agreement. Upon any such termination, You shall immediately cease all use of the Program and shall return
to Enterasys the Program and all copies of the Program.

Enterasys X-Pedition Common Command Line Interface Reference Manual v

vi Enterasys X-Pedition Common Command Line Interface Reference Manual
 Contents

About this Manual ..............................................................................................xv

What’s New? ............................................................................................................................xv
Who should Read this Manual? ...............................................................................................xv
What is Included in This Manual? ...........................................................................................xv
How to Use this Manual ...........................................................................................................xv
CLI Parameter Types ..............................................................................................................xvi
Getting Help ............................................................................................................................xix
Moving From Native to Common CLI Syntax .......................................................................xxi
Moving From Common to Native CLI Syntax .......................................................................xxi

Chapter 1: access-list Commands .......................................................................1

Command Summary ..................................................................................................................1
clear access-list counters ............................................................................................................2
show access-lists ........................................................................................................................3

Chapter 2: aging Commands ...............................................................................5

Command Summary ..................................................................................................................5
show mac-address-table aging-time ...........................................................................................6
show mls aging ...........................................................................................................................7

Chapter 3: arp Commands ..................................................................................9

Command Summary ..................................................................................................................9
arp add ......................................................................................................................................10
arp clear ....................................................................................................................................12
arp show ...................................................................................................................................13
show arp statistics ....................................................................................................................14

Enterasys X-Pedition Common Command Line Interface Reference Manual vii

 Chapter 4: atm Command .................................................................................17

Chapter 5: bgp Commands ................................................................................23

Command Summary ................................................................................................................ 23
show ip bgp ............................................................................................................................. 24
show ip bgp cidr-only .............................................................................................................. 25
show ip bgp community .......................................................................................................... 26
show ip bgp neighbor .............................................................................................................. 28
show ip bgp paths .................................................................................................................... 30
show ip bgp peer-as ................................................................................................................. 31
show ip bgp peer-group ........................................................................................................... 33
show ip bgp regexp ................................................................................................................. 34
show ip bgp summary ............................................................................................................. 36
show ip bgp sync-tree .............................................................................................................. 37

Chapter 6: cli Commands ..................................................................................39

Command Summary ................................................................................................................ 39
show history ............................................................................................................................ 40
show terminal .......................................................................................................................... 41
terminal command completion ................................................................................................ 42
terminal history size ................................................................................................................ 43
terminal length ......................................................................................................................... 44
terminal width ......................................................................................................................... 45
terminal monitor ...................................................................................................................... 46

Chapter 7: copy Commands ..............................................................................47

Command Summary ................................................................................................................ 47
copy tftp ................................................................................................................................... 48
copy tftp flash .......................................................................................................................... 50

Chapter 8: dhcp Commands ..............................................................................51

Command Summary ................................................................................................................ 51
clear ip dhcp ............................................................................................................................ 52
show ip dhcp binding .............................................................................................................. 53
show ip dhcp num-clients ........................................................................................................ 55

Chapter 9: dvmrp Commands ...........................................................................57

Command Summary ................................................................................................................ 57
show ip dvmrp interface .......................................................................................................... 58
show ip dvmrp route ................................................................................................................ 60
show ip dvmrp rules ................................................................................................................ 63

viii Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 10: enable Command ...........................................................................65

Chapter 11: exit Command ................................................................................67

Chapter 12: fddi Commands .............................................................................69

Command Summary ................................................................................................................69
clear fddi ..................................................................................................................................70
show fddi ..................................................................................................................................71

Chapter 13: file Commands ...............................................................................73

Command Summary ................................................................................................................73
delete ........................................................................................................................................74
dir .............................................................................................................................................75
show file ...................................................................................................................................76

Chapter 14: filters Commands ..........................................................................77

Command Summary ................................................................................................................78
show filters [address-filter] ......................................................................................................79
show filters [port-address-lock] ...............................................................................................80
show filters [secure-port] .........................................................................................................81
show filters [static-entry] .........................................................................................................82

Chapter 15: frame-relay Commands ................................................................85

Command Summary ................................................................................................................85
clear frame-relay ......................................................................................................................86
show frame-relay service .........................................................................................................88
show frame-relay stats .............................................................................................................89

Chapter 16: igmp Commands ............................................................................91

Command Summary ................................................................................................................91
show ip igmp interface .............................................................................................................92
show ip igmp groups ................................................................................................................94
show ip igmp timers .................................................................................................................96
igmp show vlans .......................................................................................................................97

Chapter 17: ip Commands .................................................................................99

Command Summary ................................................................................................................99
ip clear reverse-flows .............................................................................................................100
show ip hash-variant ..............................................................................................................101
show ip helper-address ...........................................................................................................103
show ip interface ....................................................................................................................104
show ip reverse-flows ............................................................................................................106
show ip route ..........................................................................................................................107
show ip route [bgp|connected|ospf|ospf-ase|rip|static] ...........................................................108
show ip route summary ..........................................................................................................109
show tcp .................................................................................................................................110
show udp ................................................................................................................................111

Enterasys X-Pedition Common Command Line Interface Reference Manual ix

 Chapter 18: ip-policy Commands ...................................................................113
Command Summary .............................................................................................................. 113
clear route-map ...................................................................................................................... 114
show route-map ..................................................................................................................... 115

Chapter 19: ip-redundancy Commands .........................................................119

Command Summary .............................................................................................................. 119
clear vrrp statistics ................................................................................................................. 120
show vrrp ............................................................................................................................... 121

Chapter 20: ip-router Commands ...................................................................123

Command Summary .............................................................................................................. 123
ip find rib-route ..................................................................................................................... 124
show gated-config ................................................................................................................. 125
show ip route ......................................................................................................................... 126
show ip route <network> ...................................................................................................... 128
show ip route state ................................................................................................................. 130

Chapter 21: ipx Commands .............................................................................131

Command Summary .............................................................................................................. 131
ipx find rip ............................................................................................................................. 132
ipx find sap ............................................................................................................................ 133
show ipx buffers .................................................................................................................... 135
show ipx interface ................................................................................................................. 136
show ipx rib destination ........................................................................................................ 137
show ipx servers .................................................................................................................... 138
show ipx route ....................................................................................................................... 139

Chapter 22: irdp Command .............................................................................141

Chapter 23: load-balance Commands .............................................................143

Command Summary .............................................................................................................. 143
load-balance set server-status ................................................................................................ 144
show load-balance acv-options ............................................................................................. 145
show load-balance hash-stats ................................................................................................ 146
show load-balance source-mappings ..................................................................................... 148
show load-balance statistics .................................................................................................. 150
show load-balance virtual-hosts ............................................................................................ 152

x Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 24: logout Command .........................................................................155

Chapter 25: mac-address-table Commands ...................................................157

Command Summary ..............................................................................................................157
show mac-address-table all-flows ..........................................................................................158
show mac-address-table all-macs ...........................................................................................160
show mac-address-table bridge-management ........................................................................161
show mac-address-table igmp-mcast-registration ..................................................................162
show mac-address-table address ............................................................................................163
show mac-address-table mac-table-stats ................................................................................164
show mac-address-table port-macs ........................................................................................165
show mac-address-table vlan-igmp-status .............................................................................167

Chapter 26: mtrace Command ........................................................................169

Chapter 27: multicast Commands ...................................................................171

Command Summary ..............................................................................................................171
show ip multicast interface ....................................................................................................172
show mroute ...........................................................................................................................174

Chapter 28: nat Commands .............................................................................177

Command Summary ..............................................................................................................177
clear ip nat ..............................................................................................................................178
clear ip nat translation ............................................................................................................179
show ip nat .............................................................................................................................181

Chapter 29: ntp Commands .............................................................................183

Command Summary ..............................................................................................................183
ntp synchronize server ...........................................................................................................184
show ntp .................................................................................................................................185

Chapter 30: ospf Commands ...........................................................................187

Command Summary ..............................................................................................................187
show ip ospf ...........................................................................................................................188
show ip ospf interface ............................................................................................................189

Enterasys X-Pedition Common Command Line Interface Reference Manual xi

 Chapter 31: ping Command ............................................................................191

Chapter 32: port Commands ...........................................................................193

Command Summary .............................................................................................................. 193
show bmon ............................................................................................................................ 195
show bridging ........................................................................................................................ 197
show interfaces ...................................................................................................................... 198
show port 8021p .................................................................................................................... 201
show port auto-negotiation .................................................................................................... 202
show port autonegotiation-capabilities .................................................................................. 203
show port MAU ..................................................................................................................... 205
show port MAU-statistics ...................................................................................................... 206
show port mirroring ............................................................................................................... 207
show port status ..................................................................................................................... 208
show pvst ............................................................................................................................... 210
show stp interface .................................................................................................................. 211
show vlan interface ................................................................................................................ 213

Chapter 33: ppp Commands ............................................................................215

Command Summary .............................................................................................................. 215
clear ppp stats-counter ........................................................................................................... 216
ppp restart lcp-ncp ................................................................................................................. 218
show ppp mlp ........................................................................................................................ 219
show ppp service ................................................................................................................... 220
show ppp stats ....................................................................................................................... 221

Chapter 34: pvst Command .............................................................................223

Chapter 35: qos Commands .............................................................................225

Command Summary .............................................................................................................. 225
show qos ip ............................................................................................................................ 226
show qos ipx .......................................................................................................................... 227
show qos l2 ............................................................................................................................ 228
show qos precedence ............................................................................................................. 230
show qos priority-map ........................................................................................................... 231
show qos wred ....................................................................................................................... 232
show qos wfq ......................................................................................................................... 233

xii Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 36: radius Command .........................................................................235

Chapter 37: rarpd Command ..........................................................................237

Chapter 38: rate-limit Command ....................................................................239

Chapter 39: reload Command .........................................................................243

Chapter 40: rip Commands .............................................................................245

Command Summary ..............................................................................................................245
rip trace ..................................................................................................................................246
show rip ..................................................................................................................................248

Chapter 41: rmon Commands .........................................................................251

clear rmon cli-filter ................................................................................................................252
clear rmon statistics ................................................................................................................253
rmon apply cli-filter ...............................................................................................................254
show rmon ..............................................................................................................................255

Chapter 42: sfs Commands ..............................................................................257

Command Summary ..............................................................................................................257
show sfs cdp-hello port-status ................................................................................................258
show sfs cdp-hello transmit-frequency ..................................................................................259

Chapter 43: smarttrunk Commands ...............................................................261

Command Summary ..............................................................................................................261
clear smarttrunk load-distribution ..........................................................................................262
show smarttrunk .....................................................................................................................263

Chapter 44: snmp Commands .........................................................................265

Command Summary ..............................................................................................................265
show snmp ..............................................................................................................................266
snmp test trap .........................................................................................................................268

Chapter 45: sonet Commands .........................................................................271

Command Summary ..............................................................................................................272
show sonet aps .......................................................................................................................273
show sonet loopback ..............................................................................................................274
show sonet medium ................................................................................................................275
show sonet pathtrace ..............................................................................................................276

Enterasys X-Pedition Common Command Line Interface Reference Manual xiii

 Chapter 46: statistics Commands ....................................................................277
Command Summary .............................................................................................................. 277
clear interface ........................................................................................................................ 279
clear ip statistics .................................................................................................................... 280
clear ipx statistics .................................................................................................................. 281
show ip icmp statistics ........................................................................................................... 282
show ip multicast ................................................................................................................... 284
show ip traffic ........................................................................................................................ 285
show ipx traffic ...................................................................................................................... 290
show port errors ..................................................................................................................... 292
show port packets .................................................................................................................. 294
show port stats ....................................................................................................................... 296
show processes cpu ............................................................................................................... 300
show rarp ............................................................................................................................... 302
show tcp statistics .................................................................................................................. 303
show traffic ............................................................................................................................ 305
show udp statistics ................................................................................................................. 306

xiv Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 47: stp Command ...............................................................................307

Chapter 48: system Commands .......................................................................309

Command Summary ..............................................................................................................309
clock set ..................................................................................................................................311
disconnect ...............................................................................................................................312
erase .......................................................................................................................................314
show bootlog ..........................................................................................................................315
show bootprom .......................................................................................................................316
show buffers ...........................................................................................................................317
show clock ..............................................................................................................................318
show contact ...........................................................................................................................319
show diagbus ..........................................................................................................................320
show environment ..................................................................................................................321
show flash ..............................................................................................................................322
show location .........................................................................................................................323
show login-banner ..................................................................................................................324
show logging ..........................................................................................................................325
show logging buffer ...............................................................................................................326
show memory .........................................................................................................................327
show name ..............................................................................................................................328
show poweron-selftest-mode .................................................................................................329
show processes .......................................................................................................................330
show running-config ..............................................................................................................331
show scratchpad .....................................................................................................................332
show sessions .........................................................................................................................333
show startup-config ................................................................................................................334
show terminal .........................................................................................................................335
show timezone ........................................................................................................................336
show uptime ...........................................................................................................................337
show users ..............................................................................................................................338
show version ..........................................................................................................................339
system hotswap ......................................................................................................................340
system image-choose .............................................................................................................342
system promimage-upgrade ...................................................................................................343

Enterasys X-Pedition Common Command Line Interface Reference Manual xv

 Chapter 49: tacacs-plus Command .................................................................345

Chapter 50: tech-support Command ..............................................................347

Chapter 51: telnet Command ..........................................................................349

Chapter 52: terminal cli native Command .....................................................351

Chapter 53: traceroute Command ..................................................................353

Chapter 54: vlan Command .............................................................................355

Chapter 55: web-cache Commands .................................................................357

Command Summary .............................................................................................................. 357
clear ip web-cache ................................................................................................................. 358
show ip web-cache ................................................................................................................ 359

Appendix A: CLI Conversion Matrix .............................................................363

xvi Enterasys X-Pedition Common Command Line Interface Reference Manual

 About this Manual

About this Manual

This manual provides reference information for the commands in the Enterasys X-
Pedition Command Line Interface (CLI). For product information not available in this
manual, see the manuals listed in Related Documentation on page 2.

What’s New?
The content of this manual includes the addition of new and extended capabilities for the following:

DHCP

dhcp show binding on page 60

dhcp show num-clients on page 61

Who should Read this Manual?

Read this manual if you are a network administrator responsible for configuring or
managing the X-Pedition.

What is Included in this Manual?

This manual includes definitions, descriptions and parameters on all show commands, as
well as all non-persistent command sets available in the Common CLI syntax with the
3.1 firmware release. Please note that it does not include command sets implemented with
the E8.0.0.0 release or above.

How to Use this Manual

The CLI commands and facilities are organized alphabetically in this manual. To locate
information about a command, go to the chapter for the command or for the facility that
contains the command. For example, to find information about the enable command, go to

Enterasys X-Pedition Common Command Line Interface Reference Manual 1

CLI Parameter Types

enable Command on page 71. To find information about the show file command, go to file
Commands on page 79, then locate the description of the show file command within that
chapter.

Related Documentation
The X-Pedition documentation set includes the following items. Refer to these other
documents to learn more about your product.

For Information About... See the...

Installing and setting up the X- Enterasys X-Pedition [Product Number]
Pedition Getting Started Guide
How to use CLI (Command Line Enterasys X-Pedition User Reference
Interface) commands to configure and
manage the X-Pedition
SYSLOG messages and SNMP traps Enterasys X-Pedition Error Reference Manual

CLI Parameter Types

The following table describes all the parameter types supported by the CLI.

Data Type Descripton Example

conditional A numerical conditional <1024 or >2048 or !=4096
expression. Special symbols are
used to describe a numerical
condition: > (greater than), < (less
than) and != (not equal to).
hexadecimal A hexadecimal number a7 or 0xa7
hostname Hostname of an IP host gauguin or john-pc
hostname/IP Hostname or IP address of a host nagasaki or 10.43.1.4
keyword A keyword described in the list of on or off
acceptable keywords in the online
help
interface name Name of a single port, or VLAN ethernet1/4 or vlan100
with created interface

2 Enterasys X-Pedition Common Command Line Interface Reference Manual

 About this Manual

Data Type Descripton Example

IP address An IP address of the form x.x.x.x. 10.1.2.3
Some commands may explicitly
require a unicast or multicast
address.
IP address list A list of IP addresses separated by “10.1.4.4 10.1.5.5 10.1.6.6”
spaces but enclosed in quotes.
IPX network An IPX network address in
address hexadecimal
IPX An IPX network and node address a1b2c3d4.08:20:a1:f3:38:11
of the form <netaddr>.<macaddr>
network.node where <netaddr> is the network or aa89f383
address address of a host and <macaddr>
is the node or MAC address of the
IPX host. For some commands, if
the node address is not given, the
node address is assumed to be a
wildcard.
IPX SAP An alphanumeric string server1
representing a valid IPX SAP
server name server name where the following
characters are illegal:
“*./:;<=>?[]\|
MAC address A MAC address specified in one 08:00:50:1a:2b:c3 or
of two forms: xx:xx:xx:xx:xx:xx 080050:1a2bc3
or xxxxxx:xxxxxx
number An integer number 100
numerical range A number or a range of numbers 3,5 or 7-10
port A single port ethernet1/4, gigabit2/1,
hssi3/1/100, or serial4/2/200
port list A list of one or more ports. To gigabit1/3-8 or
specify a range of ports within a ethernet1/(1,3,5), hssi(1-
module, describe the range in 2)/1/100, or serial4/(1-3)/200
parenthesis. You can also specify
non-consecutive ports by using
commas to separate them.
slot number A list of one or more occupied 1 or 7
slots in the X-Pedition

Enterasys X-Pedition Common Command Line Interface Reference Manual 3

Getting Help

Data Type Descripton Example

string A character string. To include abc or “abc def”
spaces in a string, specify the
entire string in double quotes (“).
URL A Uniform Resource Locator. The tftp://10.1.4.5/test/abc.txt
type of URL depends on the
command where the URL is used. rcp://dave@rtr/test/abc.txt
Currently, two URLs are
supported:
TFTP: tftp://host/pathname
RCP:
rcp://username@host/pathname

Getting Help
For additional support related to the Common CLI syntax or this document, contact
Enterasys Networks using one of the following methods:

World Wide Web http://www.enterasys.com

Phone 603-332-9400
1-800-872-8440 (toll-free in U.S. and Canada)
For the Enterasys Networks Support toll-free number in your
country: http://www.enterasys.com/support/gtac-all.html
Internet mail support@enterasys.com
To send comments or suggestions concerning this document to the Technical Writing
Department: TechWriting@enterasys.com
Make sure to include the document Part Number in the email message.

Before contacting Enterasys Networks for technical support, have the following
information ready:
• Your Enterasys Networks service contract number

• A description of the failure

• A description of any action(s) already taken to resolve the problem (e.g., changing mode
switches, rebooting the unit, etc.)

• The serial and revision numbers of all involved Enterasys Networks products in the network

4 Enterasys X-Pedition Common Command Line Interface Reference Manual

 About this Manual

• A description of your network environment (layout, cable type, etc.)

• Network load and frame size at the time of trouble (if known)

• The device history (i.e., have you returned the device before, is this a recurring problem, etc.)

• Any previous Return Material Authorization (RMA) numbers

Enterasys X-Pedition Common Command Line Interface Reference Manual 5

Getting Help

6 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Changing the CLI Syntax

Changing the CLI Syntax

The Enterasys X-Pedition firmware is designed to move easily between Native and
Common CLI syntax.The following information instructs the user on maneuvering back
and forth between these syntaxes.

Moving From Native to Common CLI Syntax

In order to switch from Native to Common CLI syntax, the X-Pedition must first be in
Enable mode. For more about Enable mode, see the Enterasys X-Pedition Command Line
Interface Reference Manual. By default, the X-Pedition boots up in User mode, under the
Native CLI syntax engine.
When the X-Pedition is in Enable mode, enter the following command:

xp# cli set common

This command will switch the X-Pedition over to Common CLI syntax.

Moving From Common to Native CLI Syntax

If the user wishes to switch back to the Native CLI syntax, the following command should
be entered while in Common CLI Privileged mode:

xp# terminal cli native

This command will return the X-Pedition CLI to the Native syntax. For more information
on Privileged mode, please see enable Command on page 71. For more information on the
terminal cli native command, see terminal cli native Command on page 357

Note: The current CLI syntax is saved in the system NVRAM. This means that if the
user reboots the X-Pedition while in Native CLI syntax, it will start up in Native
CLI syntax; likewise, if the X-Pedition is rebooted while in Common CLI syntax,
it will start up in Common CLI syntax.

Enterasys X-Pedition Common Command Line Interface Reference Manual 7

Moving From Common to Native CLI Syntax

8 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 1

access-list Commands

The access-list commands allow the user to clear ACL (Access Control List) counters and
display those Access Control Lists currently configured on the X-Pedition

Command Summary
Table 1 lists the access-list commands. The sections following the table describe the
command syntax.

Table 1. access-list commands

clear access-list counters <num>|<name>

show access-lists [<num>|<string>|{interface <string>|all-ip}|service|{port <port-
list>|all-ports}]

Enterasys X-Pedition Common Command Line Interface Reference Manual 9

clear access-list counters

clear access-list counters

Purpose
Clears one or all ACL counters.

Format
clear access-list counters <num>|<name>

Mode
Enable

Description
The clear access-list counters command allows the user to clear Access Control List
counters.With ACL logging enabled, the router prints out a message verifying whether a
packet is forwarded or dropped, and counters record these statistics. With this command,
the user can clear the ACL counters.

Parameters
<num> Clears counter based on the ACL number.

<name> Clears counter based on the name of the ACL.

Restrictions
None.

Example
To clear counters for Access Control List 100:

clear access-list counters 100

10 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show access-lists

show access-lists

Purpose
Displays one or more ACLs.

Format
show access-lists [<num>|<string>|{interface <string>|all-ip}|service|{port <port-
list>|all-ports}]

Mode
Enable

Description
The show access-lists command allows the user to display currently configured Access
Control Lists. The parameters associated with this command further allow the user to sort
and display ACLs by name, interface, port, or service type.

Parameters
<num> Specifies ACL number.

<string> Specifies ACL name.

interface Displays ACLs attached to a specific interface.

<string> Specifies name of interface

all-ip Specifies all interfaces.

service Displays ACLs applied to services

port Displays ACLs applied to a specific port(s).

<port-list> Specifies list of port(s).

all-ports Specifies display of ACLs applied to all ports.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 11

show access-lists

12 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 2

aging Commands

The aging commands control aging of learned MAC address entries in the X-Pedition’s
L2 lookup tables or layer3/4 flows. Using the aging commands, you can show L2 or layer
3/4 aging information, set or disable L2 aging on specific ports, set or disable aging of
layer 3/4 flows, or set or disable NAT or LSNAT flows.

Command Summary
Table 2 lists the l2 and l3 aging commands. The sections following the table describe the
command syntax.

Table 2. aging commands

show mac-address-table aging-time

show mls aging

Enterasys X-Pedition Common Command Line Interface Reference Manual 13

show mac-address-table aging-time

show mac-address-table aging-time

Purpose
Shows the L2 aging status for SwitchRouter ports.

Format
show mac-address-table aging-time

Mode
User

Description
The show mac-address-table aging-time command shows whether L2 aging is enabled
or disabled on SwitchRouter ports. For ports on which L2 aging is enabled, this command
also shows the aging time.

Parameters
None.

Restrictions
None.

14 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show mls aging

show mls aging

Purpose
Shows the L3 aging status for X-Pedition ports.

Format
show mls aging

Mode
User

Description
The show mls aging command shows whether L3/4 aging is enabled or disabled on X-
Pedition ports. For ports on which L3/4 aging is enabled, this command also shows the
aging time.

Parameters
None.

Restrictions
None.

Example
To show whether layer 3/4 aging is enabled and the aging time for enabled ports:

xp# show mls aging

L3 Aging: Timeout 30 seconds

Enterasys X-Pedition Common Command Line Interface Reference Manual 15

show mls aging

16 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 3

arp Commands

The arp commands enable you to add, display, and clear Address Resolution Protocol
(ARP) entries on the X-Pedition.

Command Summary
Table 3 lists the arp commands. The sections following the table describe the command
syntax.

Table 3. arp commands

arp add <host> mac-addr <MAC-addr> exit port <port> keep time <seconds>
arp clear <host> mac-addr <MAC-addr> exit port <port> keep time <seconds>
arp show <IPaddr>|all [undecoded] [unresolved] [interface <string>|all] [port
<port>]
show arp statistics <IFname>

Enterasys X-Pedition Common Command Line Interface Reference Manual 17

arp add

arp add

Purpose
Adds an ARP entry.

Format
arp add <host> mac-addr <MAC-addr> exit-port <port> keep-time <seconds>

Mode
Privileged

Description
The arp add command allows the user to manually add ARP entries to the ARP table.
Typically, the X-Pedition creates ARP entries dynamically. Using the arp add command,
you can create an ARP entry to last a specific amount of time. If the exit port is not
specified, then packets to the IP address for which the ARP entry is created are transmitted
on all ports of the interface. If an ARP request is received from the host for which the ARP
entry was created, then the exit port is updated with the port on which the ARP request
was received, so that subsequent packets are transmitted on one port only.

Parameters
<host> Hostname or IP address of this ARP entry.
mac-addr <MAC-addr>MAC address of the host.
exit-port <port> The port for which you are adding the entry. Specify the port to
which the host is connected.
keep-time <seconds> The number of seconds this ARP entry should remain in the ARP
table. A value of 0 means this is a permanent ARP entry.

Restrictions
None.

18 Enterasys X-Pedition Common Command Line Interface Reference Manual

 arp add

Examples
To create an ARP entry for the IP address 10.8.1.2 at port et.4.7 for 15 seconds:

xp# arp add 10.8.1.2 mac-addr 08:00:20:a2:f3:49 exit-port et.4.7 keep-time 15

Enterasys X-Pedition Common Command Line Interface Reference Manual 19

arp clear

arp clear

Purpose
Removes an ARP entry from the ARP table.

Format
arp clear <host> mac-addr <MAC-addr> exit-port <port> keep-time <seconds>

Mode
Privileged

Description
The arp clear command lets you manually remove entries from the ARP table. The
command can remove both dynamic and permanent entries.

Parameters
<host> Hostname or IP address of the ARP entry to remove.
mac-addr <MAC-addr> MAC address of the host.
exit-port <port> The port for which you are clearing the entry. Specify the port
to which the host is connected.
keep-time <seconds> The number of seconds this ARP entry should remain in the
ARP table. A value of 0 means this is a permanent ARP entry.

Examples
To remove the ARP for the host 10.8.1.2 from the ARP table:.

xp# arp clear 10.8.1.2

To clear the entire ARP table.

xp# arp clear all

20 Enterasys X-Pedition Common Command Line Interface Reference Manual

 arp show

arp show

Purpose
Displays the ARP table.

Format
arp show <IPaddr>|all [undecoded] [unresolved] [interface <string>| all] [port
<port>]

Mode
Privileged

Description
The arp show command displays the entire ARP table.

Parameters
<IPaddr> Shows the ARP entry for the specified IP address.
all Shows all entries in the ARP table.
undecoded Specify this optional parameter to show MAC addresses in hexadecimal
format.
unresolved Specify this optional parameter to show only MAC addresses in the ARP
table that have yet to be mapped to an network layer address.
interface Specify this optional parameter to show only addresses in the ARP table
that is associated with the specific interface.
<string> Specifies the interface name.
all Specifies all interfaces.
port Specify this optional parameter to show only addresses in the ARP table
that corresponds to a specific exit port.
<port> Specifies the exit port.

Enterasys X-Pedition Common Command Line Interface Reference Manual 21

show arp statistics

show arp statistics

Purpose
Displays ARP statistics.

Format
show arp statistics <IFname>

Mode
Privileged

Description
The show arp statistics command displays ARP statistics, such as the total number of
ARP requests and replies.

Parameters
<IFname> Displays ARP statistics for the specified interface. Failing to specify an
interface will result in the display of ARP statistics for all interfaces.

22 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show arp statistics

Example
To display ARP statistics on interface ‘en0’:

xp# show arp statistics en0

Interface en0:
1 requests sent
19 replies sent
0 proxy replies sent
Last 5 Requests Sent
----- no arp requests sent -----
Last 5 Replies Sent
134.141.179.129 | Yago 16:BF:21 |2000-04-17 13:12:49
134.141.179.129 | Yago 16:BF:21 |2000-04-17 13:50:15
134.141.179.129 | Yago 16:BF:21 |2000-04-17 15:32:32
134.141.179.129 | Yago 16:BF:21 |2000-04-17 16:17:19
134.141.179.129 | Yago 16:BF:21 |2000-04-17 11:12:44

Last 5 ARP packets received on wrong interface

----- no arp packets received on wrong interface -----

• requests sent Displays how many ARP requests have been sent
out to an ARP server for address resolution.

• replies sent Displays how many ARP replies have been sent
out to an ARP client in response to request
packets.

• proxy replies sent Displays how many proxy ARP replies have been
sent out in response to request packets. A proxy
router serving as a gateway to a subnet would
respond with a proxy reply.

• Last 5 Requests sent Displays the last five ARP requests sent,
including the following information: target MAC
address, date and time sent.

• Last 5 Replies sent Displays the last five ARP replies sent, including
the following information: target IP address, date
and time sent.

• Last 5 ARP packets received on wrong interface

Displays the last five ARP packets that has been
received on the wrong interface.

Enterasys X-Pedition Common Command Line Interface Reference Manual 23

Enterasys X-Pedition Common Command Line Interface Reference Manual 24
 Chapter 4

atm Command

The show atm command displays information specific to an Asynchronus Transfer Mode
(ATM) port.

Format
show atm [vpl port <port-list>] [vcl port <port-list>] [service <string>| all] [port-
settings <port-list>| all-ports]

Parameters
<port list> Is the port name, in the format: media.slot.port.vpi.vci
media Is the media type. This is at for an ATM port.
slot Is the slot number where the module is installed.
port Is the number of the port through which data is passing.
vpi Is the Virtual Path Identifier.
vci Is the Virtual Channel Identifier.
port-settings Shows the characteristics of an ATM port that were set by the port set
command. Specify all-ports to show characteristics of all ATM ports.
service Shows all defined ATM service profiles. Specify all to show all ATM
service profiles.
vcl port Shows VCL configurations on a port.
Specify at.slot.port to display all VCLs configured on the port.
Specify at.slot.port.vpl to display all VCLs for the specified VPL
configured on the port.
Specify at.slot.port.vpl.vcl to display only the specified VCL configured
on the port.

Enterasys X-Pedition Common Command Line Interface Reference Manual 25

 vpl port Shows VPL configurations on a port.
Specify at.slot.port to display all VPLs configured on the port.
Specify at.slot.port.vpl to display only the specified VPL configured on the
port.

Restrictions
None.

Examples
To display information about the VPL configurations on ATM port 1:

xp(atm-show)# vpl port at.9.1

VPL Table Contents for Slot 9, Port 1:

Virtual Path Identifier: 1
Administrative Status: Up
Operational Status: Up
Last State Change: 1581
Service Definition: ubr-default
Service Class: UBR
Peak Bit Rate: Best Effort
Sustained Bit Rate: 0 Kbits/sec (0 cps)
Maximum Burst Size: 0 cells
Encapsulation Type: Routed LLC
F5-OAM: Requests & Responses

• Virtual Path Identifier Identifies a particular VP.

• Administrative Status Shows whether the VP is a viable network

element.
Up indicates a viable network element.
Down indicates a non-viable network element.

• Operational Status Shows whether the VP is passing traffic.

Up indicates traffic.
Down indicates no traffic.

• Last State Change Shows the last time the VP went up or down.
Time is in seconds relative to system bootup.

• Service Definition Shows the name of the defined service and its
traffic parameters

26 Enterasys X-Pedition Common Command Line Interface Reference Manual

 To display information about all the defined service profiles for UBR:

xp# atm show service all

ubr-default
Service Class: UBR
Peak Bit Rate: Best Effort
Sustained Bit Rate: 0 Kbits/sec (0 cps)
Maximum Burst Size: 0 cells
Encapsulation Type: Routed LLC
F5-OAM: Responses Only

• Service Class Shows the type of service class.

UBR indicates Unspecified Bit Rate
CBR indicates Constant Bit Rate
RT-VBR indicates Real-time Variable Bit Rate
NRT-VBR indicates Non Real-time Variable Bit
Rate

• Peak Bit Rate Shows the maximum bit transmission rate.

• Sustained Bit Rate Shows the average bit transmission rate (in
kilobits per second).

• Maximum Burst Size Shows how many cells can be transmitted at the
Peak Bit Rate.

• Encapsulation Type Shows the encapsulation scheme to transport

multi protocol data over the AAL5 layer.
Routed-LLC indicates logical link control
encapsulation (default).
Routed-VCMUX indicates VC-based
multiplexing encapsulation.

• F5-OAM Shows how OAM (Operation, Administration,

and Management) loopback cells provide
loopback capabilities and confirm whether a VC
connection is up. Only F5 OAM segments are
supported, which provides loopback capabilities
on a VC connection level.
Responses Only indicates that the port will
respond but doesn’t generate OAM cells.
Requests & Responses indicates that the port
will respond and generate OAM cells.

Enterasys X-Pedition Common Command Line Interface Reference Manual 27

 To display port-setting information about ATM port 1:

xp(atm-show)# port-settings at.9.1

Port information for Slot 9, Port 1:
Port Type: T3 ATM coaxial cable
Xmt Clock Source: Local
Scramble Mode: Payload
Line Coding: B3ZS
Cell Mapping: Direct
Framing Cbit-Parity
VC Mode: 1 bit of VPI, 11 bits of VCI
Service Definition: ubr-default
Service Class: UBR
Peak Bit Rate: Best Effort
Sustained Bit Rate: 0 Kbits/sec (0 cps)
Maximum Burst Size: 0 cells
Encapsulation Type: Routed LLC
F5-OAM: Requests & Responses

• Port Type Shows the type of PHY interface for the port.

• Xmt Clock Source Shows the timing source for the port.
Local indicates the on board clock oscillator as
the timing source.
Loop indicates the receiver input as the timing
source.

• Scramble Mode Shows the scramble/descramble mode for the

port.
None indicates no scrambling.
Payload indicates scrambling of the payload
only.
Frame indicates scrambling of the stream only.
Both indicates scrambling of payload and stream.

• Line Coding Shows the particular DS1/T1 and DS3/T3 coding

convention.

• Cell Mapping Shows the format used to map ATM cells.

Direct indicates direct cell mapping.
Plcp indicates physical layer convergence
protocol mapping.

• Framing Shows the type of framing scheme.

cbit-parity is used for T3 framing.
m23 is used for T3 framing.
esf indicates extended super frame and is used for
T1 framing.
g832 is used for E3 framing.
g751 is used for E3 framing.

28 Enterasys X-Pedition Common Command Line Interface Reference Manual

 • VC Mode Shows the bit allocation for VPI and VCI.

• Service Definition Shows the name of the defined service on the port
and its traffic parameters.

Enterasys X-Pedition Common Command Line Interface Reference Manual 29

30 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Command Summary

Chapter 5

bgp Commands

The bgp commands let you display and set parameters for the Border Gateway Protocol
(BGP).

Command Summary
Table 4 lists the bgp commands. The sections following the table describe the command
syntax.

Table 4. bgp commands

show ip bgp [<IPaddr><IPmask>] [to-file]

show ip bgp cidr-only <IPaddr> <IPmask> [to-file]
show ip bgp community {<community-id> <as-num>|no export|no-advertise|no-
export-subconfed|reserved-community <hex-num>} [to-file]
show ip bgp neighbor <IPaddr> received-routes|all-received-routes|advertised-
routes [to-file]
show ip bgp paths <ASpath> [to-file]
show ip bgp peer-as <ASnum> [to-file]
show ip bgp peer-group external|internal|igp|routing [to-file]
show ip bgp regexp <exp>
show ip bgp summary [to-file]
show ip bgp sync-tree

Enterasys X-Pedition Common Command Line Interface Reference Manual 31

show ip bgp

show ip bgp

Purpose
Displays entries in the BGP routing table.

Format
show ip bgp [<IPaddr><IPmask>] [to-file]

Mode
Privileged

Description
The show ip bgp command displays the IP address/netmask, next hop, and AS path for
each BGP route.

Parameters
<IPaddr><IPmask> Displays information about the specified route.
to-file Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

Example
To display the BGP routing table:

xp# show ip bgp

Proto Route/Mask NextHop ASPath
BGP 172.16.70/24 172.16.20.2 (64900) 64901 IGP (Id 2)
BGP 172.16.220/24 172.16.20.2 (64900) 64901 IGP (Id 2)
BGP 192.68.20/24 172.16.20.2 (64900) 64901 IGP (Id 2)
BGP 192.68.222/24 172.16.20.2 (64900) 64901 64902 IGP (Id 3)

32 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip bgp cidr-only

show ip bgp cidr-only

Purpose
Displays routes in the BGP routing table with CIDR network masks.

Format
show ip bgp cidr-only [<IPaddr><IPmask>] [to-file]

Mode
Privileged

Description
The bgp show cidr-only command displays the same type of route information as the
show ip bgp command. The difference is that the show ip bgp cidr-only command limits
the display to CIDR routes only.

Parameters
<IPaddr><IPmask> Displays information about the specified CIDR route.
to-file Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

Example
To display information all CIDR routes in the X-Pedition’s BGP route table:

xp# bgp show cidr-only

Proto Route/Mask NextHop ASPath
BGP 12.2.19/25 207.135.89.65 (64800) 64753 64752 64751 6379 3561 11277 IGP (Id 13805)
BGP 12.5.172/22 207.135.89.65 (64800) 64753 64752 64751 6379 3561 1 IGP (Id 173)
BGP 12.5.252/23 207.135.89.65 (64800) 64753 64752 64751 6379 5646 1 7018 6301 IGP (Id 926)
BGP 12.6.42/23 207.135.89.65 (64800) 64753 64752 64751 6379 5646 1 7018 11090 IGP (Id 979)
BGP 12.6.134/23 207.135.89.65 (64800) 64753 64752 64751 6379 5646 1 701 7314 10562 IGP (Id 388)
BGP 12.7.214/23 207.135.89.65 (64800) 64753 64752 64751 6379 5646 7018 4129 IGP (Id 31004)

Enterasys X-Pedition Common Command Line Interface Reference Manual 33

show ip bgp community

show ip bgp community

Purpose
Displays routes that belong to a specified community.

Format
show ip bgp community {<community-id> <as-num>|no-export|no-advertise|no-
export-subconfed|reserved-community <hex-number>} [to-file]

Mode
Privileged

Description
The show ip bgp community command displays routes that belong to a specified
community in a specified autonomous system.

Parameters
<community-id>
This is the community identifier portion of a community split. It combines with the
autonomous-system value entered to create a value for the community attribute.
<as-num>
This is an autonomous system number.
no-export
This is a special community. It indicates the routes associated with this attribute must
not be advertised outside a BGP confederation boundary. Since the X-Pedition’s
implementation does not support confederations, this boundary is an AS boundary.
no-advertise
This is a special community. It indicates that the routes associated with this attribute
must not be advertised to other BGP peers.
no-export-subconfed
This is a special community. It indicates the routes associated with this attribute must
not be advertised to external BGP peers. (This includes peers in other members’
autonomous systems inside a BGP confederation.)
reserved-community <hex-number>
This option specifies one of the reserved communities not mentioned above. A

34 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip bgp community

reserved community is one that is in one of the following ranges (0x0000000 -

0x0000FFFF) or (0xFFFF0000 - 0xFFFFFFFF).
to-file
Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

Example
To display routes that belong to community 160 in AS 64900:

xp# show ip bgp community 160 64900

BGP table : Local router ID is 192.68.11.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
Origin codes: i - IGP, e - EGP, ? - incomplete

Network Next Hop Metric LocPrf Path

*> 192.68.20/24 172.16.20.2 64901 i
*> 192.68.222/24 172.16.20.2 64901 64902 i

Enterasys X-Pedition Common Command Line Interface Reference Manual 35

show ip bgp neighbor

show ip bgp neighbor

Purpose
Displays status information about BGP peer hosts.

Format
show ip bgp neighbor <IPaddr> received-routes|all-received-routes|advertised-routes
[to-file]

Mode
Privileged

Description
The show ip bgp neighbor command displays information related to a specified BGP
peer host. Two types of information can be displayed: routes received and accepted from a
BGP peer host, and all routes the X-Pedition has advertised to a peer host.

Parameters
<IPaddr> Specifies the IP address of a BGP peer host
received-routes Displays valid BGP routes received and accepted from the
specified peer host
all-received-routes Displays all valid BGP routes.
advertised-routes Displays all routes the X-Pedition has advertised to the specified
peer host.
to-file Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

36 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip bgp neighbor

Examples
To display all valid BGP routes received and accepted from peer host 172.16.20.2:

xp# show ip bgp neighbor 172.16.20.2 received-routes

BGP table : Local router ID is 192.68.11.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
Origin codes: i - IGP, e - EGP, ? - incomplete

Network Next Hop Metric LocPrf Path

*> 172.16.70/24 172.16.20.2 64901 i
*> 172.16.220/24 172.16.20.2 64901 i
*> 192.68.20/24 172.16.20.2 64901 i
*> 192.68.222/24 172.16.20.2 64901 64902 i

Displays all routes the X-Pedition has advertised to peer host 172.16.20.2:

xp# show ip bgp neighbor 172.16.20.2 advertised-routes

BGP table : Local router ID is 192.68.11.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
Origin codes: i - IGP, e - EGP, ? - incomplete

Network Next Hop Metric LocPrf Path

*> 172.16.20/24 172.16.20.1 i
*> 192.68.11/24 192.68.11.1 i

Enterasys X-Pedition Common Command Line Interface Reference Manual 37

show ip bgp paths

show ip bgp paths

Purpose
Displays BGP Autonomous System (AS) path information.

Format
show ip bgp paths <ASpath> [to-file]

Mode
Privileged

Description
The show ip bgp paths command displays information about a specified AS path or all
AS paths. The AS path is listed along with the number of routes that use it.

Parameters
<ASpath> Will display information about the specified AS path.
to-file Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

Example
To display information about all AS paths:

xp# show ip bgp paths

Hash Ref Path
0 5 IGP (Id 1)
2 1 (64900) 64901 64902 IGP (Id 3)
7 4 (64900) 64901 IGP (Id 2)

38 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip bgp peer-as

show ip bgp peer-as

Purpose
Displays information about TCP and BGP connections to an Autonomous System.

Format
show ip bgp peer-as <ASnum> [to-file]

Mode
Privileged

Description
The show ip bgp peer-as command displays information about routers in a specified
autonomous system that are peered with the X-Pedition.

Parameters
<ASnum> The AS number of a peer autonomous system.
to-file Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

Example
To display information about TCP and BGP connections to autonomous system 64901:

xp# show ip bgp peer-as 64901

group type External AS 64901 local 64900 flags <>
peer 172.16.20.2 version 4 lcladdr (null) gateway (null)
flags 0x20
state 0x6 <Established>
options 0x0 <>
metric_out -1 preference 170 preference2 0
recv buffer size 0 send buffer size 0
messages in 10039 (updates 5, not updates 10034) 190863 octets
messages out 10037 (updates 1, not updates 10036) 190743 octets

Enterasys X-Pedition Common Command Line Interface Reference Manual 39

show ip bgp peer-group

show ip bgp peer-group

Purpose
Displays status information about BGP peers by group.

Format
show ip bgp peer-group external|internal|igp|routing [to-file]

Mode
Enable

Description
The show ip bgp peer-group command displays status information about BGP peers
according to their group.

Parameters
external Displays status information about external peers.
internal Displays status information about internal peers.
igp Displays status information about igp peers.
routing Displays status information about routing peers.
to-file Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

Example
To display status information about external peers:

xp# show ip bgp peer-group external

Group Neighbor V AS MsgRcvd MsgSent State
external 172.16.20.2 4 64901 10045 10044 Established
BGP summary, 1 peers in group type “external”

40 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip bgp regexp

show ip bgp regexp

Purpose
Displays the BGP routes matching the AS path regular expression.

Format
show ip bgp regexp <exp>

Mode
Privileged

Description
The show ip bgp regexp command searches through all BGP routes that contain specified
keywords belonging to an AS path. These specified keywords are the AS path regular
expression upon which the search is executed. The expression string can be a combination
of AS numbers or names.
Some BGP character string shorthand conventions:
. Matches any AS number
* Zero or more repetitions
+ One or more repetitions
? Zero or one repetition
| Alternation
() Parentheses group subexpressions

Parameters
<exp> A string specifying the regular expression. Specify an AS.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 41

show ip bgp regexp

Example
To display the BGP routes starting with “64751”:

xp# show ip bgp regexp “64751 .*”

Network Next Hop Metric LocPrf Path
*> 193.226.64/22 134.141.178.33 64751 6379 1 1239 11331 8338 i

42 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip bgp summary

show ip bgp summary

Purpose
Displays the status of all BGP connections.

Format
show ip bgp summary [to-file]

Mode
Privileged

Description
The show ip bgp summary command displays the status of all BGP peers of the X-
Pedition.

Parameters
to-file Causes output to be saved in the file /gatedtrc/gated.dmp.

Restrictions
None.

Example
To display the status of all BGP connections:

xp# show ip bgp summary

Neighbor V AS MsgRcvd MsgSent Up/Down State
172.16.20.2 4 64901 10033 10031 6d23h8m1s Established
BGP summary, 1 groups, 1 peers

Enterasys X-Pedition Common Command Line Interface Reference Manual 43

show ip bgp sync-tree

show ip bgp sync-tree

Purpose
Displays the BGP synchronization tree.

Format
show ip bgp sync-tree

Mode
Privileged

Description
The show ip bgp sync-tree command displays the BGP synchronization tree. The
synchronization tree is used by IBGP peers to resolve the next hop (forwarding address). It
gives information about routes that are orphaned because the next hop could not be
resolved.

Parameters
None.

Restrictions
None.

44 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip bgp sync-tree

Examples
The following example shows the next hops for some of the routes that are not resolved
(by showing orphaned routes):

xp# show ip bgp sync tree

Task BGP_Sync_64805:
IGP Protocol: Any BGP Group: group type Routing AS 64805

Sync Tree (* == active, + == active with alternate, - ==

inactive with alternate:
Orphaned routes
Forwarding address 172.23.1.18
3/255 peer 172.23.1.26 preference 170
128.36/255.255 peer 172.23.1.26 preference 170
128.152/255.255 peer 172.23.1.26 preference 170
129.200/255.255 peer 172.23.1.26 preference 170
129.253/255.255 peer 172.23.1.26 preference 170
130.44/255.255 peer 172.23.1.26 preference 170
130.50/255.255 peer 172.23.1.26 preference 170
130.132/255.255 peer 172.23.1.26 preference 170
134.54/255.255 peer 172.23.1.26 preference 170
134.120/255.255 peer 172.23.1.26 preference 170
134.173/255.255 peer 172.23.1.26 preference 170
134.217/255.255 peer 172.23.1.26 preference 170
134.244/255.255 peer 172.23.1.26 preference 170
136.1/255.255 peer 172.23.1.26 preference 170
137.49/255.255 peer 172.23.1.26 preference 170
137.159/255.255 peer 172.23.1.26 preference 170
138.239/255.255 peer 172.23.1.26 preference 170

The following example shows the next hop for all the routes that are resolved.:

xp# bgp show sync-tree

Task BGP_Sync_64805:
IGP Protocol: Any BGP Group: group type Routing AS 64805

Sync Tree (* == active, + == active with alternate, - ==

inactive with alternate:
Node 3/8388608 route 3/255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 4/8388608 route 4/255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 6/8388608 route 6/255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 9.2/32768 route 9.2/255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 9.20/16384 route 9.20/255.255.128 metric -1 next hops 172.23.1.6 172.23.1.22
Node 10.12.1/2 route 10.12.1/255.255.255.252 metric 0 interface
Node 10.12.1.4/2 route 10.12.1.4/255.255.255.252 metric 2 next hop 172.23.1.22
Node 10.200.12/128 route 10.200.12/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 10.203.12/128 route 10.203.12/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 10.204.12/128 route 10.204.12/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12/8388608 route 12/255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.2.19/64 route 12.2.19/255.255.255.128 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.2.97/128 route 12.2.97/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.3.123/128 route 12.3.123/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.4.5/128 route 12.4.5/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.4.164/128 route 12.4.164/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.5.164/128 route 12.5.164/255.255.255 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.5.172/512 route 12.5.172/255.255.252 metric -1 next hops 172.23.1.6 172.23.1.22
Node 12.5.252/256 route 12.5.252/255.255.254 metric -1 next hops 172.23.1.6 172.23.1.22

Enterasys X-Pedition Common Command Line Interface Reference Manual 45

show ip bgp sync-tree

46 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 6

cli Commands

The cli commands allow you to change the behavior of the Command Line Interface (CLI)
in terms of command completion and command history recall.

Command Summary
Table 5 lists the cli commands. The sections following the table describe the command
syntax.

Table 5. cli commands

show history
show terminal
terminal command-completion on|off
terminal history <buffer-size>
terminal length <screen-length>
terminal width <line-length>
terminal monitor

Enterasys X-Pedition Common Command Line Interface Reference Manual 47

show history

show history

Purpose
Displays the command history from the current CLI session.

Format
show history

Mode
User

Description
The show history command shows the commands you have issued during the current CLI
session. A number is associated with each command. A command’s number is useful for
re-entering, modifying, or negating the command.
Note: You also can perform a command history recall by entering !* at any command
prompt.

Parameters
None.

Restrictions
None.

48 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show terminal

show terminal

Purpose
Displays information about the current terminal settings.

Format
show terminal

Mode
User

Description
The show terminal command shows information about the terminal settings. The terminal
settings affect the display characteristics of your CLI session.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 49

terminal command completion

terminal command completion

Purpose
Turns on or off command completion support.

Format
terminal command completion on|off

Mode
User

Description
The terminal command completion command lets you enable or disable command
completion support. This command affects only the user’s current login session.

Parameters
on Turns on command completion.
off Turns off command completion.

Restrictions
None.

50 Enterasys X-Pedition Common Command Line Interface Reference Manual

 terminal history size

terminal history size

Purpose
Modifies command history recall characteristics.

Format
terminal history size buffer-size

Mode
User

Description
The terminal history size command lets you to set the size of the command history
buffer. Each command stored in this buffer can be recalled without having the user type in
the same, complete command again. By setting the size of this history buffer, one tells the
router how many of the most recently executed commands should be stored. When the
buffer is full, the oldest command is pushed out to make space for the newest command.
This command affects only the user’s current login session.

Parameters
<buffer-size> A number specifying how many of the most recently executed commands
should be kept. To disable history support, specify a size of 0.

Restrictions
None.

Examples
To set the history buffer size to 100 commands:

xp# terminal history size 100

Enterasys X-Pedition Common Command Line Interface Reference Manual 51

terminal length

terminal length

Purpose
Modifies terminal screen’s column settings for the current session.

Format
terminal length <screen-length>

Mode
User

Description
The terminal length command lets you modify the terminal screen’s column size for the
current session.

Parameters
<screen-length> Number of columns for your terminal. Enter a number between 0-
512.

Restrictions
None.

Example
To set the number of columns to 100 lines:

xp# terminal length 100

52 Enterasys X-Pedition Common Command Line Interface Reference Manual

 terminal width

terminal width

Purpose
Modify terminal screen’s row settings for current session.

Format
terminal width <line-length>

Mode
User

Description
The terminal width command allows you to modify the terminal screen’s row settings for
the current session. Specifying the number of rows available on your terminal causes the
system to automatically pause when screen output fills the entire screen.

Parameters
<line-length> Number of rows for your terminal. Enter a number between 0-512. To
prevent output from pausing after screen fills, set the value to 0.

Restrictions
None.

Examples
To set the number of rows to 100 lines:

xp# terminal width 100

Enterasys X-Pedition Common Command Line Interface Reference Manual 53

terminal monitor

terminal monitor

Purpose
Allows the current CLI session to receive or not receive console output.

Format
terminal monitor

Mode
Privileged

Description
Some system messages are normally only sent to the management console. The terminal
monitor command allows the current CLI session to also receive those messages. This
command is useful only if you have a current Telnet CLI session and you want the
debugging output that is normally sent to the management console to also be displayed on
the Telnet session.

Parameters
None.

Restrictions
None.

54 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 7

copy Commands

The copy commands allow the user to copy a file.

Command Summary
Table 6 lists the copy commands. The sections following the table describe the command
syntax.

Table 6. copy commands

copy tftp| rcp| active| scratchpad| startup| <filename> tftp| rcp| active| scratchpad|
startup| <filename>
copy tftp flash

Enterasys X-Pedition Common Command Line Interface Reference Manual 55

copy tftp

copy tftp

Purpose
Copy configuration information or files.

Format
copy tftp| rcp| active| scratchpad| startup| <filename> tftp| rcp| active| scratchpad|
startup| <filename>

Mode
Privileged

Description
The copy command is primarily for transferring configuration information. You can copy
configuration information between the X-Pedition and external hosts using protocols such
as TFTP or RCP. Within the X-Pedition, you can copy configuration information between
the X-Pedition file system, the scratchpad (configuration database), the active (running)
configuration or the Startup configuration. You also can use the copy command to make
backup copies of a configuration file.
If the X-Pedition has two Control Modules, you can copy the startup configuration of the
primary Control Module to the secondary Control Module.

Parameters
tftp Downloads or uploads a file on a TFTP server.
rcp Downloads or uploads a file on an RCP server.
active Specifies information from the active configuration database (the running
system configuration).
scratchpad Specifies configuration changes from the scratchpad.
startup Copies the Startup configuration information stored in the Control Module’s
NVRAM.
<filename> Specifies the name of a file on the X-Pedition’s local file system (NVRAM
or PCMCIA card).

56 Enterasys X-Pedition Common Command Line Interface Reference Manual

 copy tftp

Restrictions
The X-Pedition does not allow some combinations of source and destination pair.
Typically, you cannot have the same location for both source and destination; for example,
you cannot copy from one TFTP server directly to another TFTP server or copy from
scratchpad to scratchpad.
In addition, you cannot copy directly into the active configuration from anywhere except
the scratchpad. All changes to the running system must come through the scratchpad.

Examples
To copy configuration information from the scratchpad to the active database, enter the
following command. This command activates all the uncommitted changes, thus
immediately placing the changes into effect.

xp# copy scratchpad active

To copy the file config.john to config.debi:.

xp# copy config.john config.debi

To copy the Startup configuration to a TFTP server for backup purposes, enter the
following command. The CLI prompts for the TFTP server’s IP address or hostname and
the filename:

xp# copy startup tftp-server

To copy a previously saved configuration from a TFTP server to the Startup configuration,
enter the following command. Note the use of an URL to specify the TFTP server and the
filename.

xp# copy tftp://10.1.2.3/backup/config.org startup

To copy the active configuration to a remote server using RCP, enter the following
command. Notice that in this example a URL specifies the RCP user name, server, and
filename.

xp# copy active rcp://john@server1/config/config.dec25

Enterasys X-Pedition Common Command Line Interface Reference Manual 57

copy tftp flash

copy tftp flash

Purpose
Copies a system software image to the X-Pedition.

Format
copy tftp flash

Mode
Privileged

Description
The copy tftp flash command copies a system software image from a TFTP server into
the PCMCIA flash card on the Control Module. By default, if the X-Pedition has two
Control Modules, the system software image is copied to both Control Modules.

Parameters
None. The X-Pedition will prompt for information as needed.

Restrictions
None.

58 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 8

dhcp Commands

The dhcp commands allow the user to display and clear scopes (sets of IP address pools
and network parameters) that are to be used by Dynamic Host Configuration Protocol
(DHCP) clients and apply them to interfaces on the X-Pedition.

Command Summary
Table 7 lists the dhcp commands. The sections following the table describe the command
syntax.

Table 7. dhcp commands

dhcp show binding [active| expired| static]

dhcp show num-clients

Enterasys X-Pedition Common Command Line Interface Reference Manual 59

dhcp show binding

dhcp show binding

Purpose
Display information from the lease database.

Format
dhcp show binding [active| expired| static]

Mode
Privileged

Description
The dhcp show binding command displays information from the lease database. If you do
not specify any parameters, the DHCP server displays the entire lease database.

Parameters
active Displays leases that are currently active.
expired Displays expired leases.
static Displays leases with static IP address assignments.

Restrictions
None.

Examples
To display information from the lease database:

xp# dhcp show binding

IP address Hardware Address Lease Expiration Type
------------- ---------------------- ------------------- ------
10.20.1.22 00:40:05:41:f1:2d 2003-05-24 17:45:06 dynamic
10.20.1.23 00:00:b4:b1:29:9c 2003-05-24 17:45:04 dynamic
10.20.1.21 00:00:b4:b0:f4:83 2003-05-24 17:45:01 dynamic
10.20.1.20 00:80:c8:e1:20:8a 2003-05-24 09:24:30 dynamic
10.30.7.9 08:00:20:11:22:33 static
10.30.7.44 08:00:20:44:55:66 static

60 Enterasys X-Pedition Common Command Line Interface Reference Manual

 dhcp show num-clients

dhcp show num-clients

Purpose
Displays the number of allocated bindings for the DHCP server and the maximum number
allowed.

Format
dhcp show num-clients

Mode
Privileged

Description
This dhcp show num-clients command displays the number of allocated bindings for the
DHCP server and the maximum number allowed.

Parameters
None.

Restrictions
None.

Examples
To display information:

xp# dhcp show num-clients

15 current clients (253 maximum)

Enterasys X-Pedition Common Command Line Interface Reference Manual 61

dhcp show num-clients

62 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 9

dvmrp Commands

The dvmrp commands allow the user to display information about Distance Vector
Multicast Routing Protocol (DVMRP) interfaces.

Command Summary
Table 8 lists the dvmrp commands. The sections following the table describe the command
syntax.

Table 8. dvmrp commands

show ip dvmrp interface <IPaddr>

show ip dvmrp route [<type> <slot/port> <IPaddr>]
show ip dvmrp rules

Enterasys X-Pedition Common Command Line Interface Reference Manual 63

show ip dvmrp interface

show ip dvmrp interface

Purpose
Displays DVMRP interfaces.

Format
show ip dvmrp interface [<IPaddr>]

Mode
Privileged

Description
The show ip dvmrp interface command displays the state of an interface running
DVMRP, along with other neighbor-related information. Neighbors are displayed with
their DVMRP version and capability flags and Generation IDs; this information can help
in debugging. If rules are in effect for an interface, they are indicated by ExportPol or the
ImportPol flags.

Parameters
<IPaddr> Displays DVMRP information for the specified interface.

Restrictions
None.

64 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip dvmrp interface

Examples
Here is an example of the show ip dvmrp interface command.

xp# show ip dvmrp interface

Address: 10.50.1.1 Subnet: 10.50.1/24 Met: 1 Thr: 1
Name : pc State: Dn Igmp Dvmrp

Address: 207.135.89.10 Subnet: 207.135.89.0/27 Met: 1 Thr: 1

Name : corp State: Up Igmp Dvmrp Querier ExportPol
Peer : 207.135.89.1 Version: 3.255 Flags:0xe GID: 0x31a

Address: 10.55.89.101 Subnet: 10.55.89/24 Met: 1 Thr: 1

Name : lab State: Up Dvmrp
Peer : 10.55.89.100 Version: 3.255 Flags:0xe GID: 0x179

Address: 207.135.89.10 Remote: 207.137.137.1 Met: 1 Thr: 1 Rate: 1000

Name : mbone State: Tunnel Up Dvmrp ExportPol
Peer : 207.137.137.1 Version: 3.8 Flags:0xe GID: 0x6c19d135

Enterasys X-Pedition Common Command Line Interface Reference Manual 65

show ip dvmrp route

show ip dvmrp route

Purpose
Displays DVMRP unicast routing table.

Format
show ip dvmrp route [<type> <slot/port> <IPaddr>]

Mode
Privileged

Description
The show ip dvmrp route command displays the contents of DVMRP unicast routing
table.
The DVMRP route shows the topology information for the internet multicasting sites. It is
independent of IP unicast routing table or protocol. In this table, the information is
presented about a address prefix (in form of network-address/network-mask length), the
interface and the uplink (parent) router through which this subnet can be reached. This
table also shows information about any routers/interfaces which consider this router as
their uplink (that is, those routers which depend on this router if traffic were to originate
from this subnet). These routers/interfaces are shown as children of the parent router.
Note: The show ip dvmrp route command can search on the basis of subnet and on the
basis of those routes whose parent is a particular interface and/or a particular
router.
Note: This command only shows DVMRP routes and not information about current
multicast sessions.

Parameters
<type>
<slot/port>
<IPaddr> Displays the route to the specified router.

66 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip dvmrp route

Restrictions
None.

Examples
To display DVMRP routes offered by the next-hop router 207.137.137.1:

xp# show ip dvmrp route router 207.137.137.1

DVMRP Routing Table (4232 routes, 8 hold-down-routes)
Net: 128.119.3.16/29 Gateway: 207.137.137.1 Met: 9 Age: 35
Parent: mbone Children: corp
lab

Net: 128.119.3.8/29 Gateway: 207.137.137.1 Met: 9 Age: 35

Parent: mbone Children: corp
lab

Net: 209.12.162.16/28 Gateway: 207.137.137.1 Met: 26 Age: 35

Parent: mbone Children: corp
lab

Net: 208.197.171.112/28 Gateway: 207.137.137.1 Met: 7 Age: 35

Parent: mbone Children: corp
lab

Net: 208.151.215.240/28 Gateway: 207.137.137.1 Met: 7 Age: 35

Parent: mbone Children: corp
lab

Net: 208.151.215.192/28 Gateway: 207.137.137.1 Met: 7 Age: 35

Parent: mbone Children: corp
lab

Net: 208.151.215.96/28 Gateway: 207.137.137.1 Met: 7 Age: 35

Parent: mbone Children: corp

Enterasys X-Pedition Common Command Line Interface Reference Manual 67

show ip dvmrp route

To show non-advertised routes on interface lab:

xp# show ip dvmrp route interface lab permission

DVMRP Routing Table (4232 routes, 5 hold-down-routes)
Net: 100.100.100/24 Gateway: 10.55.89.100 Met: 2 Age: 25
Parent: lab Children: corp
mbone leaf NoAdv

Net: 20.20.20/24 Gateway: 10.55.89.100 Met: 2 Age: 25

Parent: lab Children: corp
mbone leaf NoAdv

Net: 10.55.89/24 Gateway: ---- Met: 1 Age: --

Parent: lab Children: corp leaf NoAdv
mbone leaf NoAdv

Total Routes Printed: 3

68 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip dvmrp rules

show ip dvmrp rules

Purpose
Displays the rules in effect for filtering routes from DVMRP neighbor routers.

Format
show ip dvmrp rules

Mode
Privileged

Description
The show ip dvmrp rules command displays the filtering rules in effect for DVMRP
routes.

Parameters
None.

Restrictions
None.

Example
In this example, the following rules are in effect:

dvmrp advertise route 207.135.89.0/24 interface mbone

dvmrp noadvertise route 0/0 interface mbone
dvmrp advertise route 207.135.88.0/24 interface mbone
dvmrp noadvertise route 10/8 interface corp

Enterasys X-Pedition Common Command Line Interface Reference Manual 69

show ip dvmrp rules

To display information about these rules:

# show ip dvmrp rules

NoAdvertise: 10.0.0.0/8 IF: corp
Advertise : 207.135.89.0/24 IF: mbone
Advertise : 207.135.88.0/24 IF: mbone
NoAdvertise: default IF: mbone

These rules would affect the routing table as follows:

# show ip dvmrp route net 10/8 permissions

Net: 10.55.89/24 Gateway: ---- Met: 1 Age: --

Parent: lab Children: corp leaf NoAdv
mbone leaf NoAdv

These rules prevent a directly connected route on this router from being visible to interface
corp and mbone. The leaf flag indicates there is no downstream neighbor on the interface.

70 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 10

enable Command

The enable command switches the CLI session from User mode to Privileged mode.

Format
enable

Mode
User

Description
The enable command switches your CLI session from User mode to Privileged mode.
After you issue the command, the CLI will prompt you for a password if a password is
configured. If no password is configured, a warning message advising you to configure a
password will display.
If a password is configured and you do not know your password -- or pressing Return does
not work -- see your X-Pedition administrator.
To exit from the Privileged mode and return to the User mode, use the exit command.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 71

72 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Chapter 11

exit Command

The exit command exits the current CLI mode to the previous mode. For example, if you
are in the Privileged mode, exit returns you to the User mode. If you are in User mode,
exit closes your CLI session and logs you off the X-Pedition.

Format
exit

Mode
All modes

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 73

74 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Command Summary

Chapter 12

fddi Commands

The fddi commands enable the user to clear and display information related to the Fiber
Distributed Data Interface (FDDI).

Command Summary
Table 9 lists the fddi commands. The sections following the table describe the command
syntax.

Table 9. fddi commands

clear fddi <port-list>

show fddi fddi-fdx-mode| fddi-mode| fddi-status| mac-group|
mac-restricted-token| media-type| path-group| port-group| ring-purger|
smt-config| smt-group| translation| version <port-list>| all-ports

Enterasys X-Pedition Common Command Line Interface Reference Manual 75

clear fddi

clear fddi

Purpose
Clears specified FDDI port.

Format
clear fddi <port-list>

Mode
Privileged

Description
The clear fddi command clears a specified FDDI port.

Parameters
<port-list> Specifies which FDDI port(s) to clear.

Restrictions
None.

76 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show fddi

show fddi

Purpose
Displays specified information for one or more FDDI ports.

Format
show fddi fddi-fdx-mode| fddi-mode| fddi-status| mac-group|
mac-restricted-token| media-type| path-group| port-group| ring-purger|
smt-config| smt-group| translation| version <port-list>| all-ports

Mode
Privileged

Description
The show fddi command displays specified information for one or more FDDI ports.

Parameters
fddi-fdx-mode Shows FDDI full duplex value for specified port(s).
fddi-mode Shows operating FDDI mode for specified port(s).
fddi-status Shows FDDI status for specified port(s).
mac-group Shows MAC configuration parameters for specified port(s).
mac-restricted-token Shows MAC restricted token time-out for specified port(s).
media-type Shows the media type for specified port(s).
path-group Shows PATH configuration parameters for specified port(s).
port-group Shows PORT configuration parameters for specified port(s).
ring-purger Shows ring purger value for specified port(s).
smt-config Shows SMT configuration parameters for specified port(s).
smt-group Shows SMT configuration parameters for specified port(s).
translation Shows IPX/ARP Appletalk translation settings.
version Shows firmware version of port(s) specified.

Enterasys X-Pedition Common Command Line Interface Reference Manual 77

show fddi

<port-list>| all-ports Specifies FDDI port(s) for which to display chosen

information. Entering all-ports will display that information
for all FDDI ports.

Restrictions
None.

78 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 13

file Commands

The file commands enable the user to display a directory of the files on a storage device,
display the contents of a file on the console, and delete a file.

Command Summary
Table 10 lists the file commands. The sections following the table describe the command
syntax.

Table 10. file commands

delete <file-name>
dir <device-name>
show file <file-name>

Enterasys X-Pedition Common Command Line Interface Reference Manual 79

delete

delete

Purpose
Deletes a file.

Format
delete <file-name>

Mode
Privileged

Description
The delete command deletes the specified file. The filename can include a device name.
By default, if a device name is not specified, it is assumed to be the bootflash: device
which is where all configuration files are stored.

Parameters
<file-name> Name of the file to delete. The filename can include a device name using
this format: <device>:<file-name>. By default, if a device name is not
specified, it is assumed to be the bootflash device. The bootflash device is
the default device for storing configuration files.

Restrictions
None.

Examples
To delete the file config.old:

xp# delete config.old

80 Enterasys X-Pedition Common Command Line Interface Reference Manual

 dir

dir

Purpose
Displays contents of a file system.

Format
dir <device-name>

Mode
User

Description
Displays a directory of the files on the specified storage device.

Parameters
<device-name> Device name. You can specify one of the following:
bootflash: The Control Module’s NVRAM.
slot0: The PCMCIA flash card in slot 0 (the upper slot).
slot1: The PCMCIA flash card in slot 1(the lower slot).

Restrictions
None.

Examples
To display the contents of the bootflash device:

xp# dir bootflash:

Enterasys X-Pedition Common Command Line Interface Reference Manual 81

show file

show file

Purpose
Displays the contents of a file.

Format
show file <file-name>

Mode
Privileged

Description
Displays the contents of a file.

Parameters
<file-name> Name of the file to display. The filename can include a device name using
this format: <device>:<file-name>. By default, if a device name is not
specified, it is assumed to be the bootflash device. The bootflash device is
the default device for storing configuration files.

Restrictions
None.

Examples
To display the contents of the file startup (the startup configuration file):

xp# show file startup

82 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 14

filters Commands

The filters commands allow the user to display information on the following types of
security filters:
• Address filters. Address filters block traffic based on a frame’s source MAC address,
destination MAC address, or both. Address filters are always configured and applied
on the input port.
• Static entry filters. Static entry filters allow or force traffic to go to a set of destination
ports based on a frame’s source MAC address, destination MAC address, or both. Static
entry filters are always configured and applied on the input port. You can configure
source static entry filters, destination static entry filters, and flow static entry filters.
Source static entry filters allow or disallow frames based on their source MAC address;
destination static entry filters allow or disallow frames based on their destination MAC
address. Flow static entries allow or disallow traffic based on their source and
destination MAC addresses.
• Port-to-address locks. Port-to-address lock filters “lock” a user to a port or set of
ports, disallowing them access to other ports.
• Secure ports. Secure port filters shut down Layer 2 access to the X-Pedition from a
specific port or drop all Layer 2 packets received by a port. Used by themselves, secure
ports secure unused X-Pedition ports. When used in conjunction with static entry
filters, secure ports drop all received or sent traffic (depending on the static entry filter)
except traffic forced to or from the port by the static entry filter.

Enterasys X-Pedition Common Command Line Interface Reference Manual 83

Command Summary

Command Summary
Table 11 lists the filters commands. The sections following the table describe the
command syntax.

Table 11. filters commands

show filters [address-filter] [all-source| all-destination| all-flow] [source-mac

<MACaddr> des-mac <MACaddr>] [ports <ports-list>] [vlan <VLAN-num>]
show filters [port-address-lock] [ports <port-list>] [vlan <VLAN-num>] [source-
mac <MACaddr>]
show filters [secure-port]
show filters [static-entry] [all-source| all-destination| all-flow] ports <port-list>
vlan <VLAN-num> [source-mac <MAC-addr>] [des-mac <MAC-addr>]

84 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show filters [address-filter]

show filters [address-filter]

Purpose
Displays the address filters.

Format
show filters [address-filter] [all-source| all-destination| all-flow] [source-mac
<MACaddr> des-mac <MACaddr>] [ports <ports-list>] [vlan <VLAN-num>]

Mode
Privileged

Description
The show filters [address-filter] command displays the address filters currently
configured on the X-Pedition.

Parameters
all-source| all-destination| all-flow
Specifies the types of filters you want to display.
source-mac <MACaddr>
Restricts the display to only those address filters that have been applied to this source
MAC address.
des-mac <MACaddr>
Restricts the display to only those address filters that have been applied to this
destination MAC address.
ports <port-list>
Restricts the display to only those address filters that have been applied to the
specified ports.
vlan <VLAN-num>
Restricts the display to only those address filters that have been applied to the
specified VLANs.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 85

show filters [port-address-lock]

show filters [port-address-lock]

Purpose
Displays the port address locks.

Format
show filters [port-address-lock] [ports <port-list>] [vlan <VLAN-num>] [source-mac
<MACaddr>]

Mode
Privileged

Description
The show filters [port-address-lock] command displays the port-address-lock filters
currently configured on the X-Pedition.

Parameters
ports <port-list>
Restricts the display to only those port address locks that have been applied to the
specified ports.
vlan <VLAN-num>
Restricts the display to only those port address locks that have been applied to the
specified VLANs.
source-mac <MACaddr>
Restricts the display to only those port address locks that have been applied to this
source MAC address.

Restrictions
None.

86 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show filters [secure-port]

show filters [secure-port]

Purpose
Displays the port security filters.

Format
show filters [secure-port]

Mode
Privileged

Description
The show filters [secure-port] command displays the secure-port filters currently
configured on the X-Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 87

show filters [static-entry]

show filters [static-entry]

Purpose
Displays the static entry filters.

Format
show filters [static-entry] [all-source| all-destination| all-flow] ports <port-list> vlan
<VLAN-num> [source-mac <MAC-addr>] [des-mac <MAC-addr>]

Mode
Privileged

Description
The show filters [static-entry] command displays the static-entry filters currently
configured on the X-Pedition.

Parameters
all-source| all-destination| all-flow
Specifies the types of static entries you want to display.
ports <port-list>
Restricts the display to only those static entries that have been applied to the specified
ports.
vlan <VLAN-num>
Restricts the display to only those static entries that have been applied to the specified
VLANs.
source-mac <MACaddr>
Restricts the display to only those static entries that have been applied to this source
MAC address.
des-mac <MACaddr>
Restricts the display to only those static entries that have been applied to this
destination MAC address.

Restrictions
None.

88 Enterasys X-Pedition Common Command Line Interface Reference Manual

Enterasys X-Pedition Common Command Line Interface Reference Manual 89
show filters [static-entry]

90 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 15

frame-relay Commands

The frame-relay commands allow you to clear frame relay service profiles, and monitor
frame relay High-Speed Serial Interface (HSSI) and standard serial ports.

Command Summary
Table 12 lists the frame-relay commands. The sections following the table describe the
command syntax.

Table 12. frame relay commands

clear frame-relay [frame-drop-qdepth-counter] [max-frame-enqued-counter]

[frame-drop-red-counter] [rmon] [<port-list>]
show frame-relay service <service-name>| all
show frame-relay stats [ports <port-list>| all-ports] [lmi] [last-error] [mibII]
[summary]

Enterasys X-Pedition Common Command Line Interface Reference Manual 91

clear frame-relay

clear frame-relay

Purpose
Clears the specified statistics counter.

Format
clear frame-relay [frame-drop-qdepth-counter] [max-frame-enqued-counter]
[frame-drop-red-counter] [rmon] [<port list>]

Mode
Enable

Description
The clear frame-relay command allows you to specify a particular statistic counter and
have those statistics reset to zero. There are statistic counters on each WAN port, and you
can use the clear frame-relay to clear the counter for an individual WAN port or for a
group of ports.

Parameters
frame-drop-qdepth-counter Specify this optional parameter to reset the frame drop
counter to zero.
max-frame-enqued-counter Specify this optional parameter to reset the max
enquedframes counter to zero.
frame-drop-red-counter Specify this optional parameter to reset the packet drop
counter to zero.
rmon Specify this optional parameter to reset the rmon counter
to zero.
<port list> The WAN port(s) that you wish to clear the counter.

Restrictions
Usage is restricted to WAN ports only.

92 Enterasys X-Pedition Common Command Line Interface Reference Manual

 clear frame-relay

Example
To clear the frame drop counter to zero on WAN port hssi3/1:

xp# clear frame-relay frame-drop-qdepth-counter hssi3/1

Enterasys X-Pedition Common Command Line Interface Reference Manual 93

show frame-relay service

show frame-relay service

Purpose
Displays frame relay service profiles.

Format
show frame-relay service <service-name>| all

Mode
Privileged

Description
The show frame-relay service command allows the user to display the available frame
relay service profiles.

Parameters
<service name>The name of a particular pre-defined service profile.
all Displays all of the available frame relay service profiles.

Restrictions
None.

Example
To display the available frame relay service profiles named “prof1”:

xp# show frame-relay service prof1

94 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show frame-relay stats

show frame-relay stats

Purpose
Displays frame relay statistics.

Format
show frame-relay stats [ports <port-list>| all-ports] [lmi] [last-error] [mibII]
[summary]

Mode
Privileged

Description
The show frame-relay stats command allows the user to display the following frame
relay port statistics for a given port:
• The last reported frame relay error.
• The active frame relay LMI parameters.
• The MIBII statistics for frame relay WAN ports.

Parameters
port <port name>
The port or ports for which you want to display statistics. Using the keyword all-ports
will display statistics for all available ports.
lmi
Specifying the lmi keyword allows you to display the active frame relay LMI
parameters.
last-error
Specifying the last-error keyword allows you to display the last reported frame relay
error for the given port.
mibII
Specifying the mibII keyword allows you to display the MIBII statistics for frame
relay WAN ports.

Enterasys X-Pedition Common Command Line Interface Reference Manual 95

show frame-relay stats

summary
Specifying the summary keyword allows you to display all of the summary
information for VC statistics.

Restrictions
The last error, mibii, and lmi commands are for ports only (no VC designators allowed).
Otherwise, the port name may have the “VC” designator.

Examples
To display statistics for serial port 1 of slot 3:

xp# show frame-relay stats port serial3/1

96 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 16

igmp Commands

The igmp commands let you display Internet Group Management Protocol (IGMP)
parameters.

Command Summary
Table 13 lists the igmp commands. The sections following the table describe the command
syntax.

Table 13. igmp commands

show ip igmp interface <port-list>

show ip igmp groups <IPaddr>
show ip igmp timers
show ip igmp vlans

Enterasys X-Pedition Common Command Line Interface Reference Manual 97

show ip igmp interface

show ip igmp interface

Purpose
Shows the interfaces running IGMP.

Format
show ip igmp interface <port-list>

Mode
Privilege

Description
The show ip igmp interface command shows memberships on a specified interface or for
a multicast group address. When you use the command to show interfaces by group, all
interfaces containing the group membership are shown.
Note: This command is similar to show ip igmp groups, except where the show ip
igmp interface command shows interface details, the show ip igmp groups
command shows ports.

Parameters
<port-list>
The port name, in the format: media.slot.port.vpi.vci
media Is the media type. This is at for an ATM port.
slot Is the slot number where the module is installed.
port Is the number of the port through which data is passing.
vpi Is the Virtual Path Identifier.
vci Is the Virtual Channel Identifier.

Restrictions
None.

98 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip igmp interface

Example
To show information about the interfaces running IGMP:

xp# show ip igmp interface

Address: 172.1.1.10 Subnet: 172.1.1/24 Met: 1 Thr: 1

Name : mls15 State: Up Querier Leaf Igmp Dvmrp

Address: 207.135.89.64 Subnet: 207.135.89.0/25 Met: 1 Thr: 1

Name : company State: Up Querier Leaf Igmp Dvmrp
Groups : 224.0.1.12
224.1.127.255
224.0.1.24
224.2.127.253
224.2.127.254

Address: 10.135.89.10 Subnet: 10.135.89.0/25 Met: 1 Thr: 1

Name : test State: Up Querier Igmp Dvmrp

Address: 207.135.122.11 Subnet: 207.135.122.8/29 Met: 1 Thr: 1

Name : mbone State: Up Igmp Dvmrp
Groups : 224.0.1.11
224.0.1.12
224.2.127.254
239.255.255.255
224.2.127.253

Enterasys X-Pedition Common Command Line Interface Reference Manual 99

show ip igmp groups

show ip igmp groups

Purpose
Displays IGMP host memberships.

Format
show ip igmp groups <IPaddr>

Mode
Privileged

Description
The show ip igmp groups command displays IGMP host members on a specific interface
and/or for a particular multicast group.

Parameters
<Ipaddr> Address of the multicast group for which to display host memberships.

Restrictions
None.

Examples
To display host members for multicast group 225.0.1.20:

xp# show ip igmp groups 225.0.1.20

To display host members for multicast group 225.0.1.20 on port ethernet1/1:

xp# show ip igmp groups 225.0.1.20 ethernet1/1

100 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip igmp groups

The following is a fuller example.

xp# show ip igmp groups

Group : 224.0.1.11 Ports: et.1.1

Group : 224.0.1.12 Ports: et.1.1
et.5.1
Group : 224.0.1.24 Ports: et.5.1
Group : 224.1.127.255 Ports: et.5.1
Group : 224.2.127.253 Ports: et.1.1
et.5.1
Group : 224.2.127.254 Ports: et.1.1
et.5.1
Group : 239.255.255.255 Ports: et.1.1

Enterasys X-Pedition Common Command Line Interface Reference Manual 101

show ip igmp timers

show ip igmp timers

Purpose
Displays IGMP timers.

Format
show ip igmp timers

Mode
Privileged

Description
The show ip igmp timers command displays IGMP timers.

Parameters
None.

Restrictions
None.

102 Enterasys X-Pedition Common Command Line Interface Reference Manual

 igmp show vlans

igmp show vlans

Purpose
Displays IGMP VLANs.

Format
show ip igmp vlans

Mode
Privileged

Description
The igmp show vlans command displays IGMP VLANs.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 103

igmp show vlans

104 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 17

ip Commands

The ip commands allow the user to display route table entries and various IP related
tables.

Command Summary
Table 14 lists the ip commands. The sections following the table describe the command
syntax.

Table 14. ip commands

ip clear reverse-flows
show ip hash-variant
show ip helper-address
show ip interface <port-list> [brief]
show ip reverse-flows
show ip route
show ip route [bgp| connected| ospf| ospf-ase| rip| static]
show ip route summary
show ip route static/show ip route rip
show tcp [dns-lookup]
show udp [dns-lookup]

Enterasys X-Pedition Common Command Line Interface Reference Manual 105

ip clear reverse-flows

ip clear reverse-flows

Purpose
Clears reverse flow statistics.

Format
ip clear reverse-flows

Mode
Privileged

Description
The ip clear reverse-flows command deletes all reverse flow statistics. Reverse flows are
IP traffic flows in the opposite direction, where source information becomes destination
information and vice versa.

Parameters
None.

Restrictions
None.

Example
To clear the reverse flow statistics:

xp# ip clear reverse-flows

106 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip hash-variant

show ip hash-variant

Purpose
Displays IP hash variant per module.

Format
show ip hash-variant

Mode
Privileged

Description
The show ip hash-variant command displays hash variant information. There are a total
of 16 modules using the hash variant feature (1-16).
Enabling hash variant causes a variation to the basic hashing algorithm. This variation will
prevent clustering of hash values and will provide a more even distribution across the L3
lookup table. Valid variant numbers are: 0-3, 4-7 (swizzled), and 8 (auto-hashed). The
default hashing algorithm is 0.
Swizzling shifts the hash value by a certain amount of bits, causing a more random
distribution across the L3 lookup table. Auto-hashing allows the X-Pedition to auto-select
a hashing algorithm optimized for ‘best case’ L3 table distribution.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 107

show ip hash-variant

Example
To display IP hash variant information on all 16 modules:

xp# show ip hash-variant

IP Module Hash Variant
-------------------------------------------------
Module 2 variant-0
Module 3 variant-0
Module 4 variant-0
Module 5 variant-1
Module 6 variant-0
Module 7 variant-0
Module 8 variant-2
Module 9 variant-0
Module 10 variant-7
Module 11 variant-0
Module 12 variant-6
Module 13 variant-0
Module 14 variant-0
Module 15 variant-0

108 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip helper-address

show ip helper-address

Purpose
Displays the configuration of IP helper addresses.

Format
show ip helper-address

Mode
Privileged

Description
The show ip helper-address command displays the configuration of IP helper addresses
configured on the system.

Parameters
None.

Restrictions
None.

Example
The following example shows that interface int4 has one helper address configured while
interface int3 has one helper address configured for the port mapper service (port 111).

xp# show ip helper-address

Interface IP address Helper Address
--------- ---------- --------------
int6 10.1.17.1 none
int5 10.1.16.1 none
int4 10.1.15.1 10.4.1.45
int1 10.1.12.1 none
int0 10.1.11.1 none
int3 10.1.14.1 10.5.78.122(111)

Enterasys X-Pedition Common Command Line Interface Reference Manual 109

show ip interface

show ip interface

Purpose
Displays the configuration of IP interfaces.

Format
show ip interface <port-list> [brief]

Mode
Privileged

Description
The show ip interface command displays the configuration of an IP interface. If you issue
the command without specifying an interface name then the configuration of all IP
interfaces is displayed.

Parameters
<port-list> Port for which to display IP statistics.
brief This optional keyword displays a brief summary of IP interface status
and configuration.

Restrictions
None.

110 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip interface

Example
To display the configuration of the IP interface “ethernet1/1”:

xp# ip show interface ethernet1/1

ethernet1/1 is administratively up, link state is down
IP processing is disabled
Internet address is 192.168.1.1/24, Broadcast address is 192.168.1.255
Encapsulation is ARPA
MTU is 1500 bytes
Directed broadcast forwarding is disabled
Proxy ARP in enabled
ICMP redirect message are always sent
VLAN 100 is defined for IP traffic types
IP processing is enabled
Internet address is 100.1.2.1/24 Broadcast address is 100.1.1.255
Encapsulation is ARPA
MTU is 1500 bytes
Directed broadcast forwarding is disabled
Proxy ARP in enabled
ICMP redirect message are always sent

Enterasys X-Pedition Common Command Line Interface Reference Manual 111

show ip reverse-flows

show ip reverse-flows

Purpose
Displays reverse flow statistics.

Format
show ip reverse-flows

Mode
Privileged

Description
The show ip reverse-flows command displays the reverse flow statistics. Reverse flows
are IP traffic flows in the opposite direction, where source information becomes
destination information and vice versa. This command shows the number of reverse flow
packets.

Parameters
None.

Restrictions
None.

Example
To display the reverse flow statistics:

xp# show ip reverse-flows

IP Reverse Flow Statistics :
Total reverse-flow packets :0
Successful reverse-flow packets :0
Unsuccessful reverse-flow packets :0
Arphold packets :0
Find Flow entry success packets :0
Sum of arp hold and flow entry success packets : 0

112 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip route

show ip route

Purpose
Displays ARP entries on the IP routing table.

Format
show ip route

Mode
Privileged

Description
The show ip route command displays ARP entries on the IP routing table.

Parameters
None.

Restrictions
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 113

show ip route

show ip route

Purpose
Displays various portions of the IP routing table.

Format
show ip route [bgp| connected| ospf| ospf-ase| rip| static]

Mode
Privileged

Description
This show ip route command displays the IP routing table. Different command options
can be used to show different aspects of the routing table.

Parameters
bgp Shows all BGP (Border Gateway Protocol) routes.
connected Shows all connected routes.
ospf Shows all OSPF (Open Shortest Path First) routes.
ospf-ase Shows all OSPF (Open Shortest Path First) Autonomous System-External
routes.
rip Shows all RIP (Routing Information Protocol) routes.
static Shows all manually defined routes.

Restrictions
None.

114 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip route summary

show ip route summary

Purpose
Displays a summary of IP routing table entries.

Format
show ip route summary

Mode
Privileged

Description
The show ip route summary command displays a summary of all route entries.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 115

show tcp

show tcp

Purpose
Displays all TCP connections and services.

Format
show tcp [dns-lookup]

Mode
Privileged

Description
The show tcp command displays all existing TCP connections to the X-Pedition as well as
TCP services available on the X-Pedition.

Parameters
dns-lookup This command attempts to do a reverse DNS lookup to look for the
hostname associated with the IP address and display the hostname
instead.

Restrictions
None.

Example
The following example displays all established TCP connections and services of the X-
Pedition.

xp# show tcp

Active TCP connections
Proto Recv-Q Send-Q Local Address Foreign Address (state)
tcp 0 0 *:gated-gii *:* LISTEN
tcp 0 0 *:http *:* LISTEN
tcp 0 0 *:telnet *:* LISTEN

116 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show udp

show udp

Purpose
Displays all UDP connections and services.

Format
show udp [dns-lookup]

Mode
Privileged

Description
The show udp command displays all existing UDP connections to the X-Pedition
as well as UDP services available on the X-Pedition.

Parameters
dns-lookup This command attempts to do a reverse DNS lookup to look for the
hostname associated with the IP address and display the hostname
instead.

Restrictions
None.

Example

Enterasys X-Pedition Common Command Line Interface Reference Manual 117

show udp

The following example displays all established UDP connections and services of
the X-Pedition

xp# show udp

Active UDP connections
Proto Recv-Q Send-Q Local Address Foreign Address (state)
udp 0 0 127.0.0.1:1025 127.0.0.1:162
udp 0 0 *:snmp *:*
udp 0 0 *:snmp-trap *:*
udp 0 0 *:bootp-relay *:*
udp 0 0 *:route *:*
udp 0 0 *:* *:*

118 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 18

ip-policy Commands

The ip-policy commands allow the user to clear and display the policies that cause the X-
Pedition to forward packets to a specified IP address based on information in a packet’s
L3/L4 IP header fields.

Command Summary
Table 15 lists the ip-policy commands. The sections following the table describe the
command syntax.

Table 15. ip-policy commands

clear route-map [policy-name <name>|all]

show route-map [[policy-name <name>|all] [interface <name>|all]]

Enterasys X-Pedition Common Command Line Interface Reference Manual 119

clear route-map

clear route-map

Purpose
Clears IP policy statistics.

Format
clear route-map [policy-name <name>|all]

Mode
Privileged

Description
The clear route-map command is used in conjunction with the show route-map
command, which gathers statistics about IP policies. The clear route-map command lets
you reset IP policy statistics to zero.

Parameters
<name> Specifies which active IP policy to clear.
all Causes statistics to be cleared for all IP policies.

Restrictions
None.

Examples
To clear statistics for IP policy p1:

xp# clear route-map policy-name p1

To clear statistics for all IP policies:

xp# clear route-map all

120 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show route-map

show route-map

Purpose
Displays information about active IP policies.

Format
show route-map [[policy-name <name>|all] [interface <name>|all]]

Mode
Privileged

Description
The show route-map command displays information about active IP policies, including
profile definitions, policy configuration settings, and next-hop gateways. The command
also displays statistics about packets that have matched an IP policy statement as well as
the number of packets that have been forwarded to each next-hop gateway.

Parameters
policy-name <name>|all
Names a specific IP policy. Use the all keyword to display all active policies.
Note: The show route-map all command works identically to the show route-map
policy-name all command
interface <name>|all
Displays information about IP policies that have been applied to a specified interface.
If you use the all keyword, the command displays information about IP policies which
have been applied to all interfaces.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 121

show route-map

Example
To display information about IP policy p1:

xp# show route-map policy-name p1

--------------------------------------------------------------------------------
IP Policy name : p1 1
Applied Interfaces : int1 2
Load Policy : first available 3

4 5 6 7 8 9 10
ACL Source IP/Mask Dest. IP/Mask SrcPort DstPort TOS Prot
--- -------------- ------------- --------- --------- --- ----
prof1 9.1.1.5/32 15.1.1.2 any any 0 IP
prof2 2.2.2.2/32 anywhere any any 0 IP
everything anywhere anywhere any any 0 IP

Next Hop Information

--------------------
11 12 13 14 15 16 17 18
Seq Rule ACL Cnt Action Next Hop Cnt Last
--- ---- -------- --- ----------- -------- --- ----
10 permit prof1 0 Policy Only 11.1.1.2 0 Dwn
20 permit prof2 0 Policy Last 1.1.1.1 0 Dwn
2.2.2.2 0 Dwn
3.3.3.3 0 Dwn
999 permit everything 0 Policy Only drop N/A N/A
65536 deny deny 0 N/A normal fwd N/A N/A
21

Legend:
1. The name of the IP policy.
2. The interface where the IP policy was applied.
3. The load distribution setting for IP-policy statements that have more than one next-
hop gateway; either first available (the default) or round-robin.
4. The names of the profiles (created with an acl statement) associated with this IP
policy.
5. The source address and filtering mask of this flow.
6. The destination address and filtering mask of this flow.
7. For TCP or UDP, the number of the source TCP or UDP port.
8. For TCP or UDP, the number of the destination TCP or UDP port.
9. The TOS value in the packet.
10. IP protocol (ICMP, TCP UDP).

122 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show route-map

11. The sequence in which the statement is evaluated. IP policy statements are listed in the
order they are evaluated (lowest sequence number to highest).
12. The rule to apply to the packets matching the profile: either permit or deny
13. The name of the profile (ACL) of the packets to be forwarded using an IP policy.
14. The number of packets that have matched the profile since the IP policy was applied
(or since the clear route-map command was last used)
15. The method by which IP policies are applied with respect to dynamic or statically
configured routes; possible values are Policy First, Policy Only, or Policy Last.
16. The list of next-hop gateways in effect for the policy statement.
17. The number of packets that have been forwarded to this next-hop gateway.
18. The state of the link the last time an attempt was made to forward a packet; possible
values are up, dwn, or N/A.
19. Implicit deny rule that is always evaluated last, causing all packets that do not match
one of the profiles to be forwarded normally (with dynamic routes).

Enterasys X-Pedition Common Command Line Interface Reference Manual 123

show route-map

124 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 19

ip-redundancy
Commands

The ip-redundancy commands allow the user to both display and clear the Virtual Router
Redundancy Protocol (VRRP) on the X-Pedition. VRRP is defined in RFC 2338.

Command Summary
Table 16 lists the ip-redundancy commands. The sections following the table describe the
command syntax.

Table 16. ip-redundancy commands

clear vrrp statistics interface <IFnum>

show vrrp [interface <IFnum>]| summary| verbose

Enterasys X-Pedition Common Command Line Interface Reference Manual 125

clear vrrp statistics

clear vrrp statistics

Purpose
Clears statistics gathered for VRRP.

Format
clear vrrp statistics interface <IFnum>

Mode
Privileged

Description
The clear vrrp statistics command resets a number of statistics to zero. These
statistics include the number of times a Backup router became the Master, the
number of VRRP advertisements received, and counts of VRRP packets that
contain errors.

Parameters
<IFnum> Causes VRRP statistics to be cleared for all virtual routers on
the specified interface.

Restrictions
None.

Example
To clear statistics for virtual routers on interface int1:

xp# clear vrrp statistics interface int1

126 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show vrrp

show vrrp

Purpose
Displays parameters for a virtual router.

Format
show vrrp [interface <IFnum>]| summary| verbose

Mode
Privileged

Description
The show vrrp command displays parameters for a virtual router.

Parameters
interface <IFnum>
Specifies the interface where the virtual router resides. If you choose this parameter,
you may enter the following keywords:
id <vrid> Identifies and displays information about a virtual router. Specify a
number between 1-255.
summary Displays summary information about each virtual router on the
interface.
verbose Displays detailed information about each virtual router on the
interface
summary
Displays summary information about each virtual router.
verbose
Displays detailed information about each virtual router.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 127

show vrrp

Examples
To show statistics for virtual router 1 on interface int1:

xp# show vrrp interface int1 1 summary

To show statistics for all virtual routers:

xp# show vrrp summary

128 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 20

ip-router Commands

The ip-router commands allow the user to monitor features and functions that work
across the various routing protocols.

Command Summary
Table 17 lists the ip-router commands. The sections following the table describe the
command syntax.

Table 17. ip-router commands

ip find rib-route <IPaddr> [ignore-state]

show gated-config active| permanent
show ip route [summary]
show ip route <network> <mask> [detail]
show ip route state

Enterasys X-Pedition Common Command Line Interface Reference Manual 129

ip find rib-route

ip find rib-route

Purpose
Finds the active route in the RIB which the packet will use.

Format
ip find rib-route <IPaddr> [ignore-state]

Mode
Privileged

Parameters
<IPaddr>
Specifies the destination of the packet.
ignore-state
This optional parameter allows inactive routes to be considered in route
determination.

Restrictions
None.

130 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show gated-config

show gated-config

Purpose
Displays the active or startup configuration file in GateD format.

Format
show gated-config active| permanent

Mode
Privileged

Parameters
active Shows the active GateD configuration file in RAM; this is the default.
permanent Shows the permanent GateD configuration file in NVRAM, if available.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 131

show ip route

show ip route

Purpose
Displays routing information base.

Format
show ip route [summary]

Mode
Privileged

Description
The show ip route command shows the route-manager's routing information base (RIB).
For any given network, the routing daemon could have multiple routes. The active route to
any network is shown with a plus (+) sign next to it. The last active route is shown with a
minus (-) next to it. If a route has been the last active route and is also the current active
route, then it is shown with a asterisk (*) sign next to it. The legend is as follows:
• “+” Active Route
• “-” Last Active
• “*” Both
If the summary option is used, then additional information is displayed about these
routes. The announcements bits for the active route are shown, which displays the protocol
into which this route is advertised.

Parameters
summary Allows user to view additional information about the routes in the RIB.

Restrictions
None.

132 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip route

Examples:
A sample output of the show ip route command:

xp# show ip route

Routing Tables:
Generate Default: no
Destinations: 63776 Routes: 63776
Holddown: 0 Delete: 53811 Hidden: 1
Codes: Network - Destination Network Address
S - Status + = Best Route, - = Last Active, * = Both
Src - Source of the route :
Ag - Aggregate, B - BGP derived, C - Connected
R - RIP derived, St - Static, O - OSPF derived
OE - OSPF ASE derived, D - Default
Next hop - Gateway for the route ; Next hops in use: 4
Netif - Next hop interface
Prf1 - Preference of the route, Prf2 - Second Preference of the route
Metrc1 - Metric1 of the route, Metrc2 - Metric2 of the route
Age - Age of the route
Network/Mask S Src Next hop Netif Prf1 Metrc1 Metrc2 Age
------------ - --- -------- ----- ---- ------ ------ ---
3/8 * B 134.141.178.33 mls0 170 70:34:28
4/8 * B 134.141.178.33 mls0 170 70:34:28
4.17.106/24 * B 134.141.178.33 mls0 170 70:34:28
4.17.115/24 * B 134.141.178.33 mls0 170 70:34:28
4.24.148.128/25 * B 134.141.178.33 mls0 170 70:34:28
6/8 * B 134.141.178.33 mls0 170 70:34:28
6.80.137/24 * B 134.141.178.33 mls0 170 70:34:28
9.2/16 * B 134.141.178.33 mls0 170 70:34:28
9.20/17 * B 134.141.178.33 mls0 170 70:34:28
10.50/16 * C 10.50.90.1 en 0 0 0 113:31:09
10.60.90/24 * C 10.60.90.1 mls2 0 0 0 113:31:09
12/8 * B 134.141.178.33 mls0 170 70:34:28
12.1.248/24 * B 134.141.178.33 mls0 170 70:34:28
12.2.19/25 * B 134.141.178.33 mls0 170 12:47:48
12.2.76/24 * B 134.141.178.33 mls0 170 31:03:36
12.2.97/24 * B 134.141.178.33 mls0 170 1:41:30
12.2.109/24 * B 134.141.178.33 mls0 170 87:55:47
12.2.169/24 * B 134.141.178.33 mls0 170 113:31:01
12.3.63/24 * B 134.141.178.33 mls0 170 70:34:28
12.4.5/24 * B 134.141.178.33 mls0 170 70:34:28
12.4.126/24 * B 134.141.178.33 mls0 170 70:34:28
12.4.164/24 * B 134.141.178.33 mls0 170 70:34:28
12.4.175/24 * B 134.141.178.33 mls0 170 95:47:57
12.4.196/22 * B 134.141.178.33 mls0 170 70:34:28
12.5.48/21 * B 134.141.178.33 mls0 170 70:34:28
12.5.164/24 * B 134.141.178.33 mls0 170 113:31:01
12.5.252/23 * B 134.141.178.33 mls0 170 70:34:28
12.6.42/23 * B 134.141.178.33 mls0 170 70:34:28
12.6.97/24 * B 134.141.178.33 mls0 170 70:34:28

Note: To see a specific route, use the show ip route <network> command.

Enterasys X-Pedition Common Command Line Interface Reference Manual 133

show ip route <network>

show ip route <network>

Purpose
Displays the state of GateD.

Format
show ip route <network> <mask> [detail]

Mode
Privileged

Description
The show ip route <network> command displays a specific route in the route-manager's
routing information base (RIB). For any given network, the routing daemon could have
multiple routes. The active route to any network is shown with a plus (+) sign next to it.
The last active route is shown with a minus (-) next to it. If a route has been the last active
route and is also the current active route, then it is shown with a asterisk (*) sign next to it.
The legend is as follows:
• “+” Active Route
• “-” Last Active
• “*” Both
If the detail option is used, then additional information is displayed about this routes. The
announcements bits for the active route are shown, which displays the protocol into which
this route is advertised.

Parameters
<network> <mask>
Allows user to specify a particular IP address mask for the RIB route in question.
detail
Allows user to view additional information about the routes in the RIB.

Restrictions
None.

134 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip route <network>

Examples
A sample output of the ip-router show route detail command:

xp# show ip route 10.12.1.0/255.255.255.252 detail

10.12.1 mask 255.255.255.252
entries 2 announce 1
TSI:
RIP 150.1.255.255mc <> metric 1
RIP 222.1.1.255mc <> metric 1
BGP_Sync_64805 dest 10.12.1/2 metric 0
BGP group type Routing AS 64805 no metrics
Instability Histories:

*Direct Preference: 0
*NextHop: 10.12.1.2 Interface: 10.12.1.2(to-c4500)
State: <Int Active Retain>
Age: 5:12:10 Metric: 0 Metric2: 0 Tag: 0
Task: IF
Announcement bits(5):
2-KRT 4-RIP.0.0.0.0+520 5-RIP.0.0.0.0+520
6-BGP_Sync_64805
7-BGP_Group_64805
AS Path: IGP (Id 1)

OSPF Preference: -10

*NextHop: 10.12.1.1 Interface: 10.12.1.2(to-c4500)
State: <NotInstall NoAdvise Int Hidden Gateway>
Local AS: 64805
Age: 1:20:05 Metric: 1 Metric2: -1 Tag: 0
Task: OSPF
AS Path: (64805) IGP (Id 9551)
Cost: 1 Area: 0.0.0.0 Type: Net AdvRouter:
172.23.1.14

In this case there are two routes to network: 10.12.1.0 and 255.255.255.252. One of them
is a direct route and other route is learned through OSPF. The direct route has a better
preference (lower preference is considered better preference), and is thus the active route.
The direct route has been installed since 5 hours, 12 minutes and 10 seconds. This direct
route is being announced to the Forwarding Information Base (FIB) which is indicated by
KRT, over two RIP interfaces (which is indicated by 4-RIP.0.0.0.0+520, 5-
RIP.0.0.0.0+520) and also to the BGP internal peer-group for autonomous system 64805.
To see all the routes in the RIB, use the show ip route command.

Enterasys X-Pedition Common Command Line Interface Reference Manual 135

show ip route state

show ip route state

Purpose
Displays the state of GateD.

Format
show ip route state

Mode
Privileged

Description
The show ip route state command displays information on the route-manager's routing
information base (RIB).

Parameters
None.

Restrictions
None.

136 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 21

ipx Commands

The ipx commands let you add entries to the Internet Package Exchange (IPX) SAP table
for SAP servers and display the IPX forwarding database, RIP table, and SAP table.

Command Summary
Table 18 lists the ipx commands. The sections following the table describe the command
syntax.

Table 18. ipx commands

ipx find rip <address>

ipx find sap [<type>| all] [<SrvcName>| all] [<network>| all] <entrytype>
show ipx buffers
show ipx interface <IFname>
show ipx rib destination
show ipx route
show ipx servers {sorted [hops| net| name| type]}| unsorted

Enterasys X-Pedition Common Command Line Interface Reference Manual 137

ipx find rip

ipx find rip

Purpose
Finds an IPX address in the routing table.

Format
ipx find rip <address>

Mode
Privileged

Description
The ipx find rip command searches for an IPX address in the routing table.

Parameter
<address> The IPX network address of this interface. Specify the IPX address using its
hexadecimal value.

Restrictions
None.

Example
To find an IPX network in the route table:

xp# ipx find rip A1B2C3F5

138 Enterasys X-Pedition Common Command Line Interface Reference Manual

 ipx find sap

ipx find sap

Purpose
Finds a SAP entry in the routing table.

Format
ipx find sap [<type>| all] [<SrvcName>| all] [<network>| all] <entrytype>

Mode
Privileged

Description
The ipx find sap command searches for a SAP entry in the routing table.

Parameters
<type>| all Defines the types of service. Specify the service type using its hexadecimal
value. Specify all for all types of service.

<SrvcName>| all
Defines the IPX service. You can use any characters in the name except the
following: “* . / : ; < = > ? [ ] \ |
Note: Lowercase characters are changed to uppercase characters.
Specify all for all IPX services.

<network>| all
Defines the network on which the service resides. Specify an IPX network
address in the following format: <netaddr.> Example: a1b2c3d4. Specify all
for all networks.
<entrytype> Defines the types of entry you want to find. Specify one of the following:
all Finds static and dynamic SAP entries.
dynamic Finds only the dynamic SAP entries.
static Finds only the static SAP entries.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 139

ipx find sap

Example
To find a SAP entry in the route table:

xp# ipx find sap 4 FILESERVER a2b2c3d4 dynamic

140 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ipx buffers

show ipx buffers

Purpose
Displays the RIP and SAP socket buffer sizes.

Format
show ipx buffers

Mode
Enable

Description
The show ipx buffers command displays the RIP and SAP socket buffer sizes.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 141

show ipx interface

show ipx interface

Purpose
Displays the configuration of IPX interfaces.

Format
show ipx interface <IFname> [brief]

Mode
Privileged

Description
The show ipx interface command displays the configuration of an IPX interface. If you
issue the command without specifying an interface name then the configuration of all IPX
interfaces is displayed.

Parameters
<IFname> Name of the IPX interface; for example, xp14.
brief Displays a brief summary of IPX interface status and configuration.

Restrictions
If you specify an interface name, the name must belong to an existing IPX interface.

Example
To display the configuration of all IPX interfaces:

xp# show ipx interface

ethernet5/1 is administratively up, link state is down
IPX address is 00000FFF.00:00:1D:17:ED:23 encapsulation ARPA
ethernet6/1 is administratively up, link state is down
IPX address is 00000FF4.00:00:1D:17:ED:23 encapsulation ARPA

142 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ipx rib destination

show ipx rib destination

Purpose
Show IPX RIP table output sorted by destination.

Format
show ipx rib destination

Mode
User

Description
The show ipx rib destination command displays IPX RIP table output sorted by
destination.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 143

show ipx servers

show ipx servers

Purpose
Displays IPX server information.

Format
show ipx servers {sorted [hops| net| name| type]}| unsorted

Mode
User

Description
The show ipx servers command displays IPX server information sorted by any, all, or
none of the optional arguments. Sorting is done based on the order of optional arguments
given.

Parameters
sorted Confirms that user wants information sorted. Accompanies one or all of the
following arguments:
hops Sorts by number of hops away the service is.
net Sorts by the interface type over which the service arrived.
name Sorts by the Sap service name.
type Sorts by the Sap service type.
unsorted Confirms that user does not want information sorted.

Restrictions
None.

144 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ipx route

show ipx route

Purpose
Shows summary of the IPX RIP/SAP tables.

Format
show ipx route

Mode
User

Description
The show ipx route command displays a summary of the IPX RIP/SAP tables.

Parameters
None

Enterasys X-Pedition Common Command Line Interface Reference Manual 145

show ipx route

146 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 22

irdp Command

The show ip irdp command displays the state of router discovery on the X-Pedition.

Format
show ip irdp

Mode
Privileged

Description
The show ip irdp command displays the state of router discovery on the X-Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 147

Examples
To display router discovery information:

xp# show ip irdp

Task State: <Foreground NoResolv NoDetach> 1

Send buffer size 2048 at 812C68F8

Recv buffer size 2048 at 812C60D0

Timers:

RouterDiscoveryServer Priority 30

RouterDiscoveryServer_SSR2_SSR3_IP <OneShot>
last: 10:17:21 next: 10:25:05 2

Task RouterDiscoveryServer:
Interfaces:
Interface SSR2_SSR3_IP: 3
Group 224.0.0.1: 4
minadvint 7:30 maxadvint 10:00 lifetime 30:00 5

Address 10.10.5.254: Preference: 0 6

Interface policy:
Interface SSR2_SSR3_IP* MaxAdvInt 10:00 7

Legend:
1. Information about the RDISC task.
2. Shows when the last router advertisement was sent and when the next advertisement
will be sent.
3. The interface on which router advertisement is enabled.
4. Multicast address.
5. Current values for the intervals between the sending of router advertisements and the
lifetime of addresses sent in a router advertisement.
6. IP address that is included in router advertisement. The preference of this address as a
default route is 0, the default value.
7. Shows configured values for the specified interface.

148 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 23

load-balance Commands

The load-balance commands allow you to distribute session load across a pool of servers.
These commands provide a way to load balance network traffic to multiple servers.

Command Summary
Table 19 lists the load-balance commands. The sections following the table describe the
command syntax.

Table 19. load-balance commands

load-balance set server-status

show load-balance acv-options
show load-balance hash-stats
show load-balance source-mappings
show load-balance statistics
show load-balance virtual hosts

Enterasys X-Pedition Common Command Line Interface Reference Manual 149

load-balance set server-status

load-balance set server-status

Purpose
Sets the status of a load balancing server.

Format
load-balance set server-status

Mode
Privileged

Description
The load-balance set server-status command allows you to set the status of a load
balancing server.

Parameters
None.

Restrictions
None.

150 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show load-balance acv-options

show load-balance acv-options

Purpose
Displays load balance application content verification (acv) options.

Format
show load-balance acv-options

Mode
Privileged

Description
The show load-balance acv-options command allows you to display load balancing acv
options.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 151

show load-balance hash-stats

show load-balance hash-stats

Purpose
Displays load balancing hashing statistics.

Format
show load-balance hash-stats

Mode
Privileged

Description
The show load-balance hash-stats command allows you to display load balancing hash
statistics.

Parameters
None.

Restrictions
None.

Example
To display hash statistics:

152 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show load-balance hash-stats

xp# show load-balance hash-stats

Total Mappings: 4502

Top 10 Hash Depths:

+---------+----------------+------------------------+
| Index | Hash Depth | Hash Depth Occurrences |
+---------+----------------+------------------------+
|1 |0 |11882 |
|2 |1 |4226 |
|3 |2 |138 |
+---------+----------------+------------------------+

Top 10 Hash Depth Occurrences:

+---------+------------------------+----------------+
| Index | Hash Depth Occurrence | Hash Depth |
+---------+------------------------+----------------+
|1 |11882 |0 |
|2 |4226 |1 |
|3 |138 |2 |
+---------+------------------------+----------------+

Enterasys X-Pedition Common Command Line Interface Reference Manual 153

show load-balance source-mappings

show load-balance source-mappings

Purpose
Displays load balancing source-destination bindings.

Format
show load-balance source-mappings

Mode
Privileged

Description
The show load-balance source-mappings command allows you to display load balancing
source-destination bindings.

Parameters
None.

Restrictions
None.

154 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show load-balance source-mappings

Example
To display source-destination bindings:

xp# show load-balance source-mappings

Current Mappings:

FC: Flow Count

AC: Age Count
SPort: Source Port
VPort: Virtual Port
DPort: Destination Port

+----------------+-----+----------------+-----+----------------+-----+----+----+
| Source Address |Sport| Virtual IP |VPort| Dst. Address |DPort| FC | AC |
+----------------+-----+----------------+-----+----------------+-----+----+----+
|70.1.0.71 |1024 |50.1.1.18 |80 |52.1.1.73 |80 |2 |0 |
|70.1.0.71 |1025 |50.1.1.17 |80 |52.1.1.71 |80 |2 |0 |
|70.1.0.72 |1026 |50.1.1.17 |80 |52.1.1.72 |80 |2 |0 |
|70.1.0.72 |1027 |50.1.1.18 |80 |52.1.1.74 |80 |2 |0 |

4 source mapping(s) displayed.

Enterasys X-Pedition Common Command Line Interface Reference Manual 155

show load-balance statistics

show load-balance statistics

Purpose
Displays load balancing statistics.

Format
show load-balance statistics

Mode
Privileged

Description
The show load-balance statistics command allows you to display load balancing
statistics.

Parameters
None.

Restrictions
None.

156 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show load-balance statistics

Example
To display load balance statistics:

xp# show load-balance statistics

Load Balancing Packets Dropped:

No Such Virtual-IP Packet drop count: 73
TTL expired Packet drop count: 0

Load Balance Group Statistics:

Group Name: telnet Virtual-IP: 50.1.1.17 Virtual-Port: 23

No destination selected Packet drop count :0
Memory Allocation error Packet drop count :0
No forward route found Packet drop count :0
Number of Packets forwarded : 23437
Channel not Load Balancing compliant Packet drop count : 0
No hosts in group Packet drop count :0
Client in Access List Packet drop count :2

Group Name: http Virtual-IP: 50.1.1.17 Virtual-Port: 80

No destination selected Packet drop count :2
Memory Allocation error Packet drop count :0
No forward route found Packet drop count :0
Number of Packets forwarded : 34429
Channel not Load Balancing compliant Packet drop count : 0
No hosts in group Packet drop count :0
Client in Access List Packet drop count :1

Statistics of 2 groups shown.

Enterasys X-Pedition Common Command Line Interface Reference Manual 157

show load-balance virtual-hosts

show load-balance virtual-hosts

Purpose
Displays hosts in a load balancing group.

Format
show load-balance virtual-hosts

Mode
Privileged

Description
The show load-balance virtual-hosts command allows you to display the hosts in a load
balancing group.

Parameters
None.

Restrictions
None.

158 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show load-balance virtual-hosts

Example
To display load balance groups:

xp# show load-balance virtual-hosts

Load Balanced Groups:

Flow Mode Count: 0

OS: Operational state of server

AS: Admin state of server

+----------------+----------------+------+-------------+----------+------------+
| Group Name | Virtual IP | Port | Hosts Added | Hosts Up | Next Index |
+----------------+----------------+------+-------------+----------+------------+
|telnet |50.1.1.17 |23 |2 |2 |0 |
+----------------+----------------+------+-------------+----------+------------+
+-------+---------------+------+----------------+----+----+------------+
| Index | Host IP | Port | Client Count | OS | AS | Load Count |
+-------+---------------+------+----------------+----+----+------------+
|0 |52.1.1.73 |23 |0 |Up |Up |0 |
|1 |52.1.1.74 |23 |0 |Up |Up |0 |
+-------+---------------+------+----------------+----+----+------------+

+----------------+----------------+------+-------------+----------+------------+
| Group Name | Virtual IP | Port | Hosts Added | Hosts Up | Next Index |
+----------------+----------------+------+-------------+----------+------------+
|http |50.1.1.17 |80 |2 |2 |0 |
+----------------+----------------+------+-------------+----------+------------+
+-------+---------------+------+----------------+----+----+------------+
| Index | Host IP | Port | Client Count | OS | AS | Load Count |
+-------+---------------+------+----------------+----+----+------------+
|0 |52.1.1.71 |80 |0 |Up |Up |0 |
|1 |52.1.1.72 |80 |0 |Up |Up |0 |
+-------+---------------+------+----------------+----+----+------------+

Enterasys X-Pedition Common Command Line Interface Reference Manual 159

show load-balance virtual-hosts

160 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 24

logout Command

The logout command ends the CLI session.

Format
logout

Mode
All modes

Description
The logout command ends your CLI session. If you have uncommitted changes in the
scratchpad, a message warns you that the changes are not saved and gives you an
opportunity to cancel the logout and save the changes.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 161

162 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Command Summary

Chapter 25

mac-address-table
Commands

The mac-address-table commands allow the user to display various L2 tables related to
Media Access Control (MAC) addresses.

Command Summary
Table 20 lists the mac-address-table commands. The sections following the table describe
the command syntax.

Table 20. mac-address-table commands

show mac-address-table all-flows [vlan <VLAN-num>] [source-mac <mac>]

[undecoded]
show mac-address-table all-macs [vlan <VLAN-num>] [source-mac <mac>]
[source] [destination] [multicast]
show mac-address-table bridge-management
show mac-address-table igmp-mcast-registration [vlan <VLAN-num>]
show mac-address-table address <MACaddr> vlan <vlan-num>
show mac-address-table mac-table-stats
show mac-address-table port-macs <port-list>| all-ports [verbose [vlan <VLAN-
num>] [source] [destination] [multicast] [undecoded] [no-stats]]
show mac-address-table vlan-igmp-status vlan <vlan-num>

Enterasys X-Pedition Common Command Line Interface Reference Manual 163

show mac-address-table all-flows

show mac-address-table all-flows

Purpose
Shows all L2 flows (for ports in flow-bridging mode).

Format
show mac-address-table all-flows [vlan <VLAN-num>] [source-mac <mac>]
[undecoded]

Mode
User or Privileged

Description
The show mac-address-table all-flows command shows all the L2 flows learned by the
X-Pedition. The X-Pedition learns flows on ports that are operating in flow-bridging
mode.

Parameters
vlan <VLAN-num>
Specifies the VLAN number associated with the flows. The VLAN number can be
from 1 – 4095.
source-mac <mac>
Specifies the source MAC address of the flows. Enter the MAC address in either of
the following formats:

xx:xx:xx:xx:xx:xx
xxxxxx:xxxxxx
source
Specifies the source address associated with the flows.
destination
Specifies the destination address associated with the flows.
multicast
Specifies the multicast address associated with the flows.

164 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show mac-address-table all-flows

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 165

show mac-address-table all-macs

show mac-address-table all-macs

Purpose
Displays all MAC addresses currently in the L2 tables.

Format
show mac-address-table all-macs [vlan <VLAN-num>] [source-mac <mac>] [source]
[destination] [multicast]

Mode
User or Privileged

Description
The show mac-address-table all-macs command shows how many MAC addresses the
X-Pedition has in its L2 tables. You can format the displayed information based on
VLAN, source MAC address, destination MAC address or multicast.

Parameters
vlan <VLAN-num> Displays only MAC addresses in the specified VLAN.
source-mac <MACaddr>
Displays only the source MACaddress. Specify this address in either
of the following formats:
xx:xx:xx:xx:xx:xx
xxxxxx:xxxxxx
source Displays only source addresses.
destination Displays only destination addresses.
multicast Displays only multicast and broadcast addresses.

Restrictions
None.

166 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show mac-address-table bridge-management

show mac-address-table bridge-management

Purpose
Shows information about all MAC addresses registered by the system.

Format
show mac-address-table bridge-management

Mode
User or Privileged

Description
The show mac-address-table bridge-management command shows MAC addresses that
have been inserted into the L2 tables for management purposes. Generally, these entries
are configured so that a port forwards a frame to the Control Module if the management
MAC matches the frame’s destination MAC.
An example of a bridge-management MAC is Spanning Tree’s bridge group address
(0180C2:000000), which is be registered in the L2 tables of X-Pedition ports on which the
Spanning Tree Protocol (STP) is enabled.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 167

show mac-address-table igmp-mcast-registration

show mac-address-table igmp-mcast-registration

Purpose
Displays information about multicast MAC addresses registered by IGMP.

Format
show mac-address-table igmp-mcast-registration [vlan <VLAN-num>]

Mode
User or Privileged

Description
The show mac-address-table igmp-mcast-registration command displays the multicast
MAC addresses that IGMP has registered with the L2 tables. The X-Pedition forwards the
multicast MAC addresses only to the ports that IGMP specifies.

Parameters
vlan <VLAN-num> Displays only the multicast MAC addresses registered for the
specified VLAN.

Restrictions
None.

168 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show mac-address-table address

show mac-address-table address

Purpose
Displays information about a particular MAC address.

Format
show mac-address-table address <MACaddr> vlan <VLAN-num>

Mode
User or Enable

Description
The show mac-address-table address command displays the port number on which the
specified MAC address resides.

Parameters
<MACaddr> Specifies a MAC address. Enter the MAC address in either of the
following formats:
xx:xx:xx:xx:xx:xx
xxxxxx:xxxxxx
vlan <VLAN-num> Displays the MAC address for this VLAN.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 169

show mac-address-table mac-table-stats

show mac-address-table mac-table-stats

Purpose
Displays statistics for the MAC addresses in the MAC address tables.

Format
show mac-address-table mac-table-stats

Mode
User or Privileged

Description
The show mac-address-table mac-table-stats command displays statistics for the master
MAC address table in the Control Module and the MAC address tables on the individual
ports.

Parameters
None.

Restrictions
None.

170 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show mac-address-table port-macs

show mac-address-table port-macs

Purpose
Displays information about MACs residing in a port's L2 table.

Format
show mac-address-table port-macs <port-list>| all-ports [verbose [vlan <VLAN-
num>] [source] [destination] [multicast] [undecoded] [no-stats]]

Mode
User or Privileged

Description
The show mac-address-table port-macs command shows the information about the
learned MAC addresses in individual L2 MAC address tables. Each port has its own MAC
address table. The information includes the number of source MAC addresses and the
number of destination MAC addresses in the table. If you enter the verbose option, the
MAC addresses also are displayed.

Parameters
<port-list>| all-ports
Specifies the port(s) for which you want to display MAC address information. You
can specify a single port or a comma-separated list of ports. If you use the all-ports
keyword, MAC address information is displayed for all ports.
verbose
Shows detailed statistics for each MAC address entry.
vlan <VLAN-num>
Specifies the type of MAC address for which you want to show statistics.
source
Displays statistics for only source addresses.
destination
Displays statistics for only destination addresses.
multicast
Displays statistics for only multicast and broadcast addresses.

Enterasys X-Pedition Common Command Line Interface Reference Manual 171

show mac-address-table port-macs

undecoded
Displays the MAC addresses in hexadecimal format rather than undecoded format.
Undecoded format does not show the vendor name in place of the first three
hexadecimal digits (example: Enterasys:33:44:55). The default is undecoded
(example: 00:11:22:33:44:55).
no-stats
Lists the MAC addresses without displaying any statistics.

Restrictions
None.

172 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show mac-address-table vlan-igmp-status

show mac-address-table vlan-igmp-status

Purpose
Shows whether IGMP is on or off on a VLAN.

Format
show mac-address-table vlan-igmp-status vlan <VLAN-num>

Mode
Privileged

Description
The show mac-address-table vlan-igmp-status command shows the multicast MAC
addresses that IGMP has registered with the L2 tables. This command also shows the ports
to which the multicast MAC addresses are forwarded.
Note: For IGMP forwarding to occur for a multicast MAC address, IGMP must be
enabled on the VLAN with which the MAC address is associated.

Parameters
vlan <VLAN-num> Specifies the VLAN number. The VLAN number can range from 1 –
4095.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 173

show mac-address-table vlan-igmp-status

174 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 26

mtrace Command

The mtrace command tracks the multicast path from a source to the X-Pedition.

Format
mtrace <source>

Mode
Privileged

Description
The mtrace command tracks the multicast path from a source to a receiver. A trace probe
is sent in a reverse path from the receiver back to the source. As the probe passes from hop
to hop, it collects information such as interface address and packet counts from each
router. Because the mtrace command is executed with only the source parameter, a
multicast path is calculated from the source to the X-Pedition.

Parameters
<source> IP address of the source.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 175

Examples
To display the multicast path from IP address 2.2.2.2 to the X-Pedition:

xp# mtrace 2.2.2.2

176 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 27

multicast Commands

The multicast commands allow the user to display information about IP multicast
interfaces.

Command Summary
Table 21 lists the multicast commands. The sections following the table describe the
command syntax.

Table 21. multicast commands

show ip multicast interface

show mroute [child <IPaddr>] [group <IPaddr>] [parent <IPaddr>]

Enterasys X-Pedition Common Command Line Interface Reference Manual 177

show ip multicast interface

show ip multicast interface

Purpose
Displays information about IP multicast interfaces.

Format
show ip multicast interface

Mode
Privileged

Description
The show ip multicast interface command displays interfaces that are running IGMP or
DVMRP.
Note: This command is a superset of the show dvmrp interface and
show igmp interface commands.

Parameters
None.

Restrictions
None.

178 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip multicast interface

Example
To display IP multicast information:

xp# show ip multicast interface

Address: 172.1.1.10 Subnet: 172.1.1/24 Met: 1 Thr: 1

Name : mls15 State: Up Querier Leaf Igmp Dvmrp

Address: 207.135.89.64 Subnet: 207.135.89.0/25 Met: 1 Thr: 1

Name : company State: Up Querier Leaf Igmp Dvmrp
Groups : 224.0.1.12
224.1.127.255
224.0.1.24
224.2.127.253
224.2.127.254

Address: 10.135.89.10 Subnet: 10.135.89.0/25 Met: 1 Thr: 1

Name : test State: Up Querier Igmp Dvmrp
Peer : 10.135.89.67 Flags: 0xe Version: 3.255

Address: 190.1.0.1 Subnet: 190.1/16 Met: 1 Thr: 1

Name : rip State: Dis

Address: 207.135.122.11 Subnet: 207.135.122.8/29 Met: 1 Thr: 1

Name : mbone State: Up Igmp Dvmrp
Peer : 207.135.122.10 Flags: 0xe Version: 3.255
Groups : 224.0.1.11
224.0.1.12
224.2.127.254
239.255.255.255
224.2.127.253

Address: 10.40.1.10 Subnet: 10.40.1/24 Met: 1 Thr: 1

Name : downstream State: Up Dvmrp
Peer : 10.40.1.1 Flags: 0xf Version: 3.255

Address: 10.100.1.1 Subnet: 10.100.1/24 Met: 1 Thr: 1

Name : dan State: Dn Dvmrp

Enterasys X-Pedition Common Command Line Interface Reference Manual 179

show mroute

show mroute

Purpose
Displays the IP multicast routing table.

Format
show mroute [child <IPaddr>] [group <IPaddr>] [parent <IPaddr>]

Mode
Privileged

Description
The show mroute command displays the IP multicast routing table entry for the specified
multicast group address.
This command lists all the multicast distribution trees, showing the parent interface (from
where the traffic is coming), and the children distribution interfaces (to which the traffic is
being forwarded). It would also show any cache information available either in hardware
forwarding mechanism or in the main processor (for software based forwarding).
Note: The cache information can be timed out when not enough traffic is present, but
multicast routes can still be present. Cache information is presented in number of
flows (Layer 4 sessions). Multicast routes stay at least for 5 minutes, while the
hardware forwarding mechanism can time out a flow faster.
Any pruning information, if present, is also shown.
The search can always be narrowed by looking at a particular group, and/or looking at a
particular parent interface, and/or looking at a particular child interface.
Multicast routes are not the same as DVMRP routes.

Parameters
child <IPaddr> Address of a child interface.
group <IPaddr> Address of a multicast group.
parent <IPaddr> Address of a parent interface.

180 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show mroute

Restrictions
None.

Examples
To display the IP multicast route entry for the group 225.0.0.10:

xp# show mroute group 225.0.0.10

Below is a fuller example of the output from this command:

xp# show mroute

Network: 130.207.8/24 Group: 224.2.1.1 Age: 99s
Parent : mbone Child: test
downstream
Source : 130.207.8.82 Pkts: 383 Flows: 1

Network: 131.120.63/24 Group: 224.2.1.1 Age: 63s

Parent : mbone Pruned Child: test Pruned
downstream Pruned
Source : 131.120.63.33 Pkts: 0 Flows: 0

Network: 147.6.65.0/25 Group: 224.2.2.1 Age: 48s

Parent : mbone Pruned Child: test Pruned
downstream Pruned
Source : 147.6.65.38 Pkts: 0 Flows: 0

Enterasys X-Pedition Common Command Line Interface Reference Manual 181

show mroute

182 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 28

nat Commands

The nat commands allow the user to clear and display Network Address Translation
(NAT) bindings for local (inside) and global (outside) network addresses.

Command Summary
Table 22 lists the nat commands. The sections following the table describe the command
syntax.

Table 22. nat commands

clear ip nat out-of-globals| port-mode

clear ip nat translation [pool-specified [local-acl-pool <local-ACL>] [global-pool
<IPaddr/IPaddr-range>]]
show ip nat [statistics| timeouts| translations]

Enterasys X-Pedition Common Command Line Interface Reference Manual 183

clear ip nat

clear ip nat

Purpose
Clears NAT error statistics.

Format
clear ip nat out-of-globals| port-mode

Mode
Privileged

Description
The clear ip nat command allows you to clear specific NAT error statistics such as
out-of-globals messages in the case of dynamic bindings and port misconfiguration.

Parameters
out-of-globals Clears error statistics during dynamic binding in the case where there are
no more global IP addresses in the global address pool.
port-mode Clears error statistics that occur because of port misconfigurations. Such
cases are where the port is set to either destination-based forwarding or
host-flow based forwarding.

Restrictions
None

Example
To clear all out-of-global error statistics:

xp# clear ip nat out-of-globals

184 Enterasys X-Pedition Common Command Line Interface Reference Manual

 clear ip nat translation

clear ip nat translation

Purpose
Clears dynamic NAT bindings.

Format
clear ip nat translation [pool-specified [local-acl-pool <local-ACL>] [global-pool
<IPaddr/IPaddr-range]]

Mode
Privileged

Description
The clear ip nat translation command deletes dynamic address bindings. You can delete
the dynamic address bindings for specific address pools.

Parameters
pool-specified
Deletes NAT dynamic bindings based on local and global acl pools.
local-acl-pool <local-ACL>
The ACL that corresponds to the local IP address pool.
global-pool <IPaddr/IPaddr-range>
The global address pool, defined in one of the following ways:
A single IP address in the form a.b.c.d
An IP address range in the form 10.10.1.1-10.10.1.50
IP address and mask in the form 1.2.0.0/255.255.0.0 or 1.2.3.0/16

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 185

clear ip nat translation

Examples
To delete dynamic address bindings for the local address pool that corresponds to the ACL
‘lcl’ and the global address pool that corresponds to 136.1.1.1-136.1.1.254:

xp# clear ip nat translation pool-specified local-acl-pool lcl global-pool 136.1.1.0/24

186 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip nat

show ip nat

Purpose
Displays NAT information.

Format
show ip nat [statistics| timeouts| translations]

Mode
Privileged

Description
The show ip nat command allows you to display NAT address statistics, timeouts, and
translations.

Parameters
statistics Displays NAT statistics.
timeouts Displays the current set of timeouts.
translations Displays NAT translations.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 187

show ip nat

Examples
To display active NAT translations:

xp# show ip nat translations

Proto Local/Inside Global/Outside IP Type No. of flows

----- --------------------- --------------------- --------------- ------------
TCP 15.15.15.15:1896 100.1.1.1:1026 Dyn. ovr. 2
TCP 15.15.15.15:1897 100.1.1.1:1028 Dyn. ovr. 0
TCP 15.15.15.15:1894 100.1.1.1:1024 Dyn. ovr. 2
TCP 15.15.15.15:1895 100.1.1.1:1025 Dyn. ovr. 2
TCP 15.15.15.15:1892 100.1.1.1:1027 Dyn. ovr. 0
IP 10.10.10.10:* 200.1.1.1:* Dynamic 20
IP 4.4.4.4:* 202.1.1.1:* Static 789

To display NAT timeouts:

xp# show ip nat timeouts

All values in minutes

Flow FTP Sess. DNS Sess. Dyn. Sess.
------ --------- --------- ----------
2 30 30 1440

188 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 29

ntp Commands

The ntp commands configure and display the characteristics of the NTP (Network Time
Protocol) client.

Command Summary
Table 23 lists the ntp commands. The sections following the table describe the command
syntax.

Table 23. ntp commands

ntp synchronize server <host>

show ntp

Enterasys X-Pedition Common Command Line Interface Reference Manual 189

ntp synchronize server

ntp synchronize server

Purpose
Manually forces the X-Pedition to immediately synchronize with an NTP server.

Format
ntp synchronize server <host>

Mode
Privileged

Description
The ntp synchronize server command forces the X-Pedition to immediately synchronize
its clock with the NTP server.

Parameters
<host> Specifies the hostname or the IP address of the NTP server.

Restrictions
None.

Examples
To synchronize the X-Pedition against the NTP server 10.13.1.1:

xp# ntp synchronize server 10.13.1.1

%NTP-I-TIMESYNC, Time synchronized to Thu Aug 3 23:11:28 2000

190 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ntp

show ntp

Purpose
Displays NTP information about the X-Pedition.

Format
show ntp

Mode
Privileged

Description
The show ntp command displays various NTP information about the X-Pedition, for
example, the last time a successful synchronization was made, synchronization interval,
NTP version number, etc.

Parameters
None.

Restrictions
None.

Example
xp# show ntp
NTP status:
Synchronization interval: 60 mins
Version: NTPv3
Last successful contact: Thu Jan 23 23:08:15 1999

Enterasys X-Pedition Common Command Line Interface Reference Manual 191

show ntp

192 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 30

ospf Commands

The ospf commands allow the user to display parameters for the Open Shortest Path First
(OSPF) routing protocol.

Command Summary
Table 24 lists the ospf commands. The sections following the table describe the command
syntax.

Table 24. ospf commands

show ip ospf
show ip ospf interface

Enterasys X-Pedition Common Command Line Interface Reference Manual 193

show ip ospf

show ip ospf

Purpose
Displays OSPF information.

Format
show ip ospf

Mode
Privileged

Description
The show ip ospf command displays information about the OSPF.

Parameters
None.

Restrictions
None.

194 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip ospf interface

show ip ospf interface

Purpose
Displays OSPF interfaces.

Format
show ip ospf interface

Mode
Privileged

Description
The show ip ospf interface command displays all OSPF interfaces.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 195

show ip ospf interface

196 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 31

ping Command

The ping command tests connection between the X-Pedition and an IP host.

Format
ping <hostname-or-IPaddr> packets <num> size <num> wait <num> [flood]
[dontroute]

Mode
Privileged

Description
The ping command test connection between the X-Pedition and an IP host. The ping
command sends ICMP echo packets to the host you specify.
• If the packets reach the host, the host sends a ping response to the X-Pedition and the
CLI displays messages stating that the host can be reached.
• If the host does not respond, the X-Pedition assumes the host cannot be reached from
the X-Pedition and the CLI display messages stating that the host did not reply.

Parameters
<hostname-or-IPaddr>
The host name or IP address you want to ping.
packets <num>
The number of ping packets you want to send. The default is 1.
size <num>
The packet size. For Ethernet, specify a number from 0 – 1364.

Enterasys X-Pedition Common Command Line Interface Reference Manual 197

 wait <num>
The number of seconds the X-Pedition will wait for a positive response from the
host before assuming that the host has not responded. The default is 1.
flood
Causes the X-Pedition to send a new ping request as soon as a ping reply is
received. If you do not specify the flood option, the X-Pedition waits to send a
new request. The amount of time the X-Pedition waits is specified by the wait
option.
dontroute
Restricts the ping to locally attached hosts.

Restrictions
None.

198 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 32

port Commands

The port commands display the following parameters:

• Port state (enabled or disabled)
• Bridging status (flow-based or address-based)
• Port operating mode (half duplex or full duplex)
• Port speed for the 10/100 ports (10-Mbps or 100-Mbps)
• Port mirroring (used for analyzing network traffic)
• Port shut down if broadcast threshold is reached

Command Summary
Table 25 lists the port commands. The sections following the table describe the command
syntax.

Table 25. port commands

show bmon
show bridging
show interfaces accounting| <port-list>
show port 8021
show port auto-negotiation <port-list>
show port auto-negotiation capabilities <port-list>
show port MAU [<port-list>]
show port MAU-statistics [<port-list>]

Enterasys X-Pedition Common Command Line Interface Reference Manual 199

Command Summary

Table 25. port commands (Continued)

show port mirroring [<port-list>| acls]

show port status <port-list>
show pvst <name> interface <port-list>
show stp interface <port-list>
show vlan interface <port-list>

200 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show bmon

show bmon

Purpose
Displays broadcast monitoring information for X-Pedition ports.

Format
show bmon

Mode
Privileged

Description
The show bmon command allows the user to display broadcast monitoring information
for all X-Pedition ports.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 201

show bmon

Example
To display the state of ports with broadcast monitoring:

ssr# show bmon

Port: ethernet1/1 State: On

Port: ethernet6/8 State: ShutDn Expire: 39 (sec)

Port: ethernet7/8 State: On

The above example shows three ports, with the port ethernet6/8 shut down for 39 seconds.

202 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show bridging

show bridging

Purpose
Displays the bridging status of all X-Pedition ports.

Format
show bridging

Mode
Privileged

Description
The show bridging command lets you display bridging-status information for all X-
Pedition ports.

Parameters
None.

Restrictions
None.

Example
To display the bridging status for available ports:

xp# show bridging

Port Mgmt Status phy-state link-state Bridging Mode
---- ----------- --------- ---------- -------------
ethernet4/1 No Action Disabled Link Down Address
ethernet4/2 No Action Disabled Link Down Address
ethernet4/3 No Action Forwarding Link Up Address
ethernet4/4 No Action Disabled Link Down Address
ethernet4/5 No Action Disabled Link Down Address
ethernet4/6 No Action Forwarding Link Up Address
ethernet4/7 No Action Disabled Link Down Address
ethernet4/8 No Action Disabled Link Down Address

Enterasys X-Pedition Common Command Line Interface Reference Manual 203

show interfaces

show interfaces

Purpose
Displays the user defined descriptions of X-Pedition ports.

Format
show interfaces accounting| <port-list>

Mode
Privileged

Description
The show interfaces command allows you display the user defined description for X-
Pedition ports.

Parameters
accounting Displays interface accounting.
<port-list> Specifies the port(s) for which you want to display the description(s).

Restrictions
This command is valid for Ethernet and WAN only.

204 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show interfaces

Examples
To display status for ethernet3/1-2:

ssr# show interfaces ethernet3/1-2

ethernet3/1 is administratively up, link state is up
Hardware is 10/100-Mbit Ethernet, address is 0000.1d17.ed21
Internet address is 100.1.2.1/24
MTU 1522 bytes, Speed 1 Mbits
Encapsulation ETHERNET_II, loopback not set, Half duplex
ARP type: ARPA, ARP keep-time not set (permanent)
Statistics was never cleared.
Five minute input rate 1008 bits/sec, 1 packets/sec
Five minute output rate 1008 bits/sec, 1 packets/sec
3198 packets input, 402886 bytes, 0 no buffer
Received 0 multicast, 0 broadcast, 0 runts, 0 giants
0 input errors, 0 CRC, 0 bad frames, 0 overrun
3252 packets output, 409205 bytes, 0 underruns
Received 56 multicast, 56 broadcast
0 output errors, 0 collisions, 0 late collisions
0 deferred, 0 false carriers, 0 buffer failures
ethernet3/2 is administratively up, link state is down
Hardware is 10/100-Mbit Ethernet, address is 0000.1d17.ed21
Internet address is 100.1.3.1/24
MTU 1522 bytes, Speed N/A
Encapsulation ETHERNET_II, loopback not set
ARP type: ARPA, ARP keep-time not set (permanent)
Statistics was never cleared.
Five minute input rate 0 bits/sec, 0 packets/sec
Five minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 multicast, 0 broadcast, 0 runts, 0 giants
0 input errors, 0 CRC, 0 bad frames, 0 overrun
0 packets output, 0 bytes, 0 underruns
Received 0 multicast, 0 broadcast
0 output errors, 0 collisions, 0 late collisions
0 deferred, 0 false carriers, 0 buffer failures

Enterasys X-Pedition Common Command Line Interface Reference Manual 205

show interfaces

To display accounting statistics for all ports:

ssr# show interfaces accounting

Interface ethernet6/1:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 3486 439174 3541 445747
IP 0 0 0 0
IPX 0 0 0 0
Interface ethernet6/2:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 0 0 0 0
IP 0 0 0 0
Interface ethernet6/3:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 0 0 0 0
IP 0 0 0 0
Interface ethernet6/4:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 0 0 0 0
IP 0 0 0 0
Interface ethernet6/5:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 0 0 0 0
IP 0 0 0 0
Interface ethernet6/6:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 0 0 0 0
IP 0 0 0 0
Interface ethernet6/7:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 0 0 0 0
IP 0 0 0 0
Interface ethernet6/8:
Protocol Pkts In Bytes In Pkts Out Bytes Out
Total 103 12346 1 126
IP 0 0 0 0

206 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port 8021p

show port 8021p

Purpose
Displays 802.1p encapsulation status.

Format
show port 8021p

Mode
Privileged

Description
The show port 8021p command displays whether 802.1p encapsulation is enabled or
disabled on a port or list of ports. The 802.1p standard provides the ability to classify
traffic into eight priority categories or class of services. This classification scheme is based
upon MAC frame information and is used for QoS (Quality of Service) for VLANs.

Parameters
None.

Restrictions
None.

Example
To display 802.1p encapsulation status for port ethernet2/1:

xp# port show 8021p ethernet2/1

Port 802.1p Status

---- -------------
ethernet2/1 Disabled

Enterasys X-Pedition Common Command Line Interface Reference Manual 207

show port auto-negotiation

show port auto-negotiation

Purpose
Displays auto-negotiation information.

Format
show port auto-negotiation <port-list>

Mode
Privileged

Description
The show port auto-negotiation command displays auto-negotiation information. This
command displays port number, administration status, current status, remote signaling,
fault advertised, and fault received. Auto-negotiation is a process whereby both ports on a
connection resolve the best line speed, duplex mode and flow control scheme to
communicate with each other.

Parameters
<port-list> Specifies the ports for which you want to display the description.
Failing to specify a port will result in the display of all the X-
Pedition ports.

Restrictions
None.

Example
To display auto-negotiation information for port ethernet2/1:

xp# show port autonegotiation ethernet2/1

Admin Current Remote Fault Fault

Port Status Status Signalling Advertised Received
------ -------- ------------- ------------ ------------- ----------
ethernet2/1 disabled other not detected n/a n/a

208 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port autonegotiation-capabilities

show port autonegotiation-capabilities

Purpose
Displays auto-negotiation capabilities.

Format
port show auto-negotiation capabilities <port-list>

Mode
Privileged

Description
The show port auto-negotiation capabilities command displays a list of port capabilities,
advertised capabilities, and any received capabilities from another port. Auto-negotiation
is a process whereby both ports on a connection resolve the best line speed, duplex mode
and flow control scheme to communicate with each other.

Parameters
<port-list> Specifies the ports for which you want to display capabilities. Failing to
specify a port will result in the display of all the X-Pedition ports.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 209

show port autonegotiation-capabilities

Example
To display auto-negotiation capabilities for port ethernet2/1:

xp# show port autonegotiation-capabilities ethernet2/1

Port Capability Advertised Received

------ -------------- -------------- --------------
et2/1 other other
10 baseT 10 baseT
10 baseT FD 10 baseT FD
100 baseT4 100 baseT4
100 baseTX 100 baseTX
100 baseTX FD 100 baseTX FD
100 baseT2 100 baseT2
100 baseT2 FD 100 baseT2 FD
Pause Pause
Asymmetric Pause Asymmetric Pause
Symmetric Pause Symmetric Pause
Asym-Sym Pause Asym-Sym Pause
1000 baseX 1000 baseX
1000 baseX FD 1000 baseX FD
1000 baseT 1000 baseT
1000 baseT FD 1000 baseT FD

210 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port MAU

show port MAU

Purpose
Displays Media Access Control information.

Format
show port MAU <port-list>

Mode
Privileged

Description
The show port MAU command displays Media Access Control (MAC) information. This
command displays port number, media type, default media type, jack type, operational
status, and support level.

Parameters
<port-list> Specifies the ports for which you want to display the description.

Restrictions
None.

Example
To display MAC information for port ethernet2/1:

xp# show port MAU ethernet2/1

Port MUA Type Default Type Jack Type Status Supported

------ -------------- -------------- --------- ----------- ---
et.2.1 100 BaseFX HD 100 BaseFX HD fiber SC operational no

Enterasys X-Pedition Common Command Line Interface Reference Manual 211

show port MAU-statistics

show port MAU-statistics

Purpose
Displays Media Access Control statistics.

Format
show port MAU-statistics <port-list>

Mode
Privileged

Description
The show port MAU-statistics command displays Media Access Control (MAC)
statistics. This command displays port number, media availability, media availability state
exits totals, jabber (excessively long frames) state, jabbering state enters totals, and false
carriers totals.

Parameters
<port-list> Specifies the ports for which you want to display the description.

Restrictions
None.

Example
To display MAC statistics for port ethernet2/1:

xp# show port MAU-statistics ethernet2/1

Media Avail. Jabber Jabbering False

Port Media Avail. State Exits State State Enters Carriers
------ ---------------- ------------ --------- ------------ ----
ethernet2/1 not available 0 other 0 0

212 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port mirroring

show port mirroring

Purpose
Shows the port mirroring status for ports and ACLs in the X-Pedition chassis.

Format
show port mirroring <port-list>| acls

Mode
Privileged

Description
The show port mirroring command shows the following port mirroring status
information for the specified ports or ACLs:
• Whether port mirroring is enabled
• The ports or slots that are being mirrored
• The mirroring mode (input port, output slot, or both)

Parameters
<port-list> Specifies the ports for which you want to display port mirroring status.
acls Displays information for all flow mirroring rules.

Restrictions
None.

Examples
To display the port mirroring status for port ethernet2/1:

xp# show port mirroring ethernet2/1

Enterasys X-Pedition Common Command Line Interface Reference Manual 213

show port status

show port status

Purpose
Displays various information about specified ports.

Format
show port status <port-list>

Mode
Privileged

Description
The show port status command lets you display port-status information for X-Pedition
ports.

Parameters
<port-list> Specifies the LAN/WAN ports for which you want to display status
information.

Restrictions
This command does not show Virtual Circuit (VC) information. To see the state of sub-
interfaces, you need to use the appropriate facility command, such as the show frame-
relay command.

214 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port status

Example
To display the port status for all ports on ethernet1/2:

xp# show port status ethernet1/2

Flags: M - Mirroring enabled S - SmartTRUNK port

Link Admin
Port Port Type Duplex Speed Negotiation State State Flags
---- --------- ------ ----- ----------- ----- ----- -----
et.1.1 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up
et.1.2 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up
et.1.3 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up
et.1.4 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up
et.1.5 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up
et.1.6 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up
et.1.7 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up
et.1.8 10/100-Mbit Ethernet Half 10 Mbits Manual Up Up

Enterasys X-Pedition Common Command Line Interface Reference Manual 215

show pvst

show pvst

Purpose
Displays Spanning Tree (STP) information for a particular spanning tree.

Format
show pvst <name> interface <port-list>

Mode
Privileged

Description
The show pvst command allows the user to display Spanning-Tree information for a
particular spanning tree.

Parameters
<name> Specifies the name of the spanning tree for which you want to
display information.
interface <port-list> Specifies the ports for which you want to display information.

Restrictions
None.

Example
To display the spanning tree information for spanning tree ‘stp1’ on port ethernet2/1:

xp# show pvst stp1 interface ethernet2/1

216 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show stp interface

show stp interface

Purpose
Displays Spanning Tree (STP) information for X-Pedition ports.

Format
show stp interface <port-list>

Mode
Privileged

Description
The show stp interface command allows the user to display Spanning-Tree information
for X-Pedition ports.

Parameters
<port-list> Specifies the ports for which you want to display information. If no
port list is specified, the command will display information for all
X-Pedition ports.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 217

show stp interface

Example
To display the spanning tree information for all available ports:

xp# show stp interface

Designated
Port Priority Cost STP State Designated-Bridge Port
---- -------- ---- --- ----- ----------------- ----------
et.1.1 128 00100 Enabled Listening 8000:00e063111111 80 01
et.1.2 128 00100 Enabled Listening 8000:00e063111111 80 02
et.1.3 128 00100 Enabled Listening 8000:00e063111111 80 03
et.1.4 128 00100 Enabled Listening 8000:00e063111111 80 04
et.1.5 128 00100 Enabled Listening 8000:00e063111111 80 05
et.1.6 128 00100 Enabled Listening 8000:00e063111111 80 06
et.1.7 128 00100 Enabled Listening 8000:00e063111111 80 07
et.1.8 128 00100 Enabled Listening 8000:00e063111111 80 08

218 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show vlan interface

show vlan interface

Purpose
Displays VLAN information for X-Pedition ports.

Format
show vlan interface <port-list>

Mode
Privileged

Description
The show vlan interface command allows the user to display VLAN information about
X-Pedition ports.

Parameters
<port-list> Specifies the ports for which you want to display information.If no
port list is specified, the command will display information for all
X-Pedition ports.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 219

show vlan interface

Example
To display the VLAN information for all available ports:

xp# show vlan interface

Port Access Type IP VLANs IPX VLANs Bridging VLANs
------ --------- --------- -------- --------------
et.4.1 access DEFAULT DEFAULT DEFAULT
et.4.2 access DEFAULT DEFAULT DEFAULT
et.4.3 access DEFAULT DEFAULT DEFAULT
et.4.4 access DEFAULT DEFAULT DEFAULT
et.4.5 access DEFAULT DEFAULT DEFAULT
et.4.6 access DEFAULT DEFAULT DEFAULT
et.4.7 access DEFAULT DEFAULT DEFAULT
et.4.8 access DEFAULT DEFAULT DEFAULT

220 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 33

ppp Commands

The ppp commands allow the user to specify and monitor Point-to-Point Protocol (PPP)
service profiles and PPP High-Speed Serial Interface (HSSI) and standard serial ports.

Command Summary
Table 26 lists the ppp commands. The sections following the table describe the command
syntax.

Table 26. ppp commands

clear ppp stats-counter ports <port-list> [[frame-drop-qdepth-counter] [max-

frame-enqued-counter] frame-drop-red-counter] [rmon]]
ppp restart lcp-ncp ports <port-list>
show ppp mlp <mlp-list>| all-ports
show ppp service <service name>| all
show ppp stats port <port> [bridge-ncp] [ip-ncp] [link-status] [summary]

Enterasys X-Pedition Common Command Line Interface Reference Manual 221

clear ppp stats-counter

clear ppp stats-counter

Purpose
Clears the specified statistics counter.

Format
ppp clear stats-counter ports <port list> [[frame-drop-qdepth-counter] [max-frame-
enqued-counter] [frame-drop-red-counter] [rmon]]

Mode
Privileged

Description
The clear ppp stats-counter command allows the user to specify a particular statistic
counter and reset those statistics to zero. There are statistic counters on each PPP WAN
port, and you can use the clear ppp stats-counter to clear the counter for an individual
WAN port or for a group of ports.

Parameters
ports <port list> The WAN port(s) for which you wish to clear counter.
frame-drop-qdepth-counter Specifying this optional parameter will reset the frame
drop counter to zero.
max-frame-enqued-counter Specifying this optional parameter will reset the max
enquedframes counter to zero.
frame-drop-red-counter Specifying this optional parameter will reset the packet
drop counter to zero.
rmon Specifying this optional parameter will reset the rmon
counter to zero.

Restrictions
Usage is restricted to PPP WAN ports only.

222 Enterasys X-Pedition Common Command Line Interface Reference Manual

 clear ppp stats-counter

Example
To clear the frame drop counter to zero on WAN port hs.3.1:

xp# clear ppp port hs.3.1 frame-drop-qdepth-counter

Enterasys X-Pedition Common Command Line Interface Reference Manual 223

ppp restart lcp-ncp

ppp restart lcp-ncp

Purpose
Restarts PPP LCP/NCP negotiation.

Format
ppp restart lcp-ncp ports <port list>

Mode
Privileged

Description
The ppp restart lcp-ncp command allows the user to reset and restart the LCP/NCP
negotiation process for PPP WAN ports.

Parameters
ports <port list> The ports for which you would like to re-establish LCP/NCP
negotiation.

Restrictions
This command line is available only for PPP WAN ports.

Example
To restart LCP/NCP negotiation on serial ports 1 and 2 of slot 4:

xp# ppp restart lcp-ncp ports serial4/1-2

224 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ppp mlp

show ppp mlp

Purpose
Displays the PPP ports that have been added into an MLP bundle.

Format
show ppp mlp <mlp list>| all-ports

Mode
Privileged

Description
The show ppp mlp command allows the user to display information about one or more
MLP bundles.

Parameters
<mlp list> The name(s) of the MLP bundles on which you want information. You
can specify a single bundle or a comma-separated list of MLP bundles.
all-ports Displays information on all MLP ports.

Restrictions
None.

Example
To display the PPP ports for mp.1:

xp# show ppp mlp mp.1

mp.1:
Slot: 4
PPP ports: serial4/1,serial4/3

Enterasys X-Pedition Common Command Line Interface Reference Manual 225

show ppp service

show ppp service

Purpose
Displays PPP service profiles.

Format
show ppp service <service name>| all

Mode
Privileged

Description
The show ppp service command allows you to display one or all of the available PPP
service profiles.

Parameters
<service name>The service profile you wish to display.
all Displays all of the available PPP service profiles.

Restrictions
None.

Example
To display the available PPP service profiles named profile_4:

xp# show ppp service profile_4

226 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ppp stats

show ppp stats

Purpose
Displays bridge NCP, IP NCP, and link-status parameters.

Format
show ppp stats port <port> [bridge-ncp] [ip-ncp] [link-status] [summary]

Mode
Privileged

Description
The show ppp stats command allows the user to display parameters for bridge NCP, IP
NCP, and link-status on PPP WAN ports. You may specify one, two, or three of the
available parameter types.

Parameters
port <port> The PPP WAN port for which you wish to view bridge NCP, IP NCP, and/or
link-status parameters.
bridge-ncp Specifies that you wish to view bridging NCP parameters for the given port.
ip-ncp Specifies that you wish to view IP NCP parameters for the given port.
link-status Specifies that you wish to view link-status parameters for the given port.
summary Specifies that you wish to view summarized display.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 227

show ppp stats

Example
To display the available link-status and IP NCP parameters for the PPP WAN interface
located at slot 4, port 1:

xp# show ppp stats port serial4/1 ip-ncp link-status

228 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 34

pvst Command

The show pvst command displays Shielded Twisted Pair (STP) bridging information for a
particular VLAN.

Format
show pvst <VLANid>

Mode
Privileged

Description
The show pvst command displays STP bridging information for a particular VLAN.

Parameters
<VLANid> The name of the VLAN for which to display STP information.
Note: For default VLAN, use stp commands.

Restrictions
For PVST, the spanning tree instance must have previously been created.

Enterasys X-Pedition Common Command Line Interface Reference Manual 229

230 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Command Summary

Chapter 35

qos Commands

The qos commands display Quality of Service (QoS) parameters.

Command Summary
Table 27 lists the qos commands. The sections following the table describe the command
syntax.

Table 27. qos commands

show qos ip
show qos ipx
show qos l2 all-destination all-flow ports <port-list> vlan <VLANid> source-mac
<MACaddr> dest-mac <MACaddr>
show qos precedence ip| ipx
show qos priority-map <string>| all
show qos wred [input port <port-list>| all-ports] [port <port-list>| all-ports]
show qos wfq <port-list>| all-ports

Enterasys X-Pedition Common Command Line Interface Reference Manual 231

show qos ip

show qos ip

Purpose
Displays QoS information for IP flows.

Format
show qos ip

Mode
Privileged

Description
The show qos ip command allows the user to display QoS information for IP flows.

Parameters
None.

Restrictions
None.

232 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show qos ipx

show qos ipx

Purpose
Displays QoS information for IPX flows.

Format
show qos ipx

Mode
Privileged

Description
The show qos ipx command allows the user to display QoS information for IPX flows.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 233

show qos l2

show qos l2

Purpose
Displays QoS information for L2 flows.

Format
show qos l2 all-destination all-flow ports <port-list> vlan <vlanID> source-mac
<MACaddr> dest-mac <MACaddr>

Mode
Privileged

Description
The show qos l2 command allows the user to display QoS information for L2 flows. You
may filter the display according to the following:
• Destinations
• Flows
• Ports
• VLANs
• Source MAC addresses
• Destination MAC addresses
• Priority

Parameters
all-destination
Filters the display to show all the L2 destination priorities.
all-flow
Filters the display to show all the L2 flow priorities.
ports <port-list>
Filters the display to show L2 priority information for specific ports.
vlan <vlanID>
Filters the display to show L2 priority information for specific VLANs.

234 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show qos l2

source-mac <MACaddr>
Filters the display to show L2 priority information for specific source MAC addresses.
dest-mac <MACaddr>
Filters the display to show L2 priority information for specific destination MAC
addresses.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 235

show qos precedence

show qos precedence

Purpose
Displays IP or IPX precedence values.

Format
show qos precedence ip| ipx

Mode
Privileged

Description
The show qos precedence command allows the user to display the precedence values for
all fields in a flow.
IP flows consist of the following fields: destination port, destination address, source port,
source IP address, TOS, interface, protocol.
IPX flows consist of the following fields: destination network, source network, destination
node, source node, destination port, source port, interface.

Parameters
ip Displays the precedence values for IP flows.
ipx Displays the precedence values for IPX flows.

Restrictions
None.

236 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show qos priority-map

show qos priority-map

Purpose
Displays the priority mapping and the ports that it is applied.

Format
show qos priority-map <string>| all

Mode
Privileged

Description
The show qos priority-map command allows the user to display the priority mapping that
is configured on a port. The command details how each set of 802.1p tag values is mapped
to a specific internal priority queue.

Parameters
<string> Specifies the name of the priority map.
all Displays all priority maps.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 237

show qos wred

show qos wred

Purpose
Displays WRED parameters for each port.

Format
show qos wred [input port <port list>| all-ports] [port <port list>| all-ports]

Mode
Privileged

Description
The show qos wred command allows the user to display WRED information for a certain
port or all ports. You may display WRED parameter information according to the
following:
• Input ports
• All Ports

Parameters
input port <port list>| all-ports
Displays input port WRED parameters. Specify all-ports to display parameters for all
ports.
port <port list>| all-ports
Displays WRED parameters for each port. Specify all-ports to display parameters for
all ports.

Restrictions
None.

238 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show qos wfq

show qos wfq

Purpose
Displays bandwidth allocated for each port.

Format
show qos wfq port <port list>| all-ports

Mode
Privileged

Description
The show qos wfq command allows the user to display the bandwidth for each port
allocated with weighted-fair queuing.

Parameters
port <port list> |all-ports
Displays bandwidth allocated for each port. Specify a list of ethernet or wan ports.
Specify all-ports to display bandwidth for all ports.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 239

show qos wfq

240 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 36

radius Command

The show radius command displays information about Remote Authentication Dial-In
Service (RADIUS) configuration on the X-Pedition.

Format
show radius

Mode
Privileged

Description
The show radius command displays statistics and configuration parameters related to
RADIUS configuration on the X-Pedition. The statistics displayed include:
accepts Number of times each server responded and validated the user successfully.
rejects Number of times each server responded and denied the user access, either
because the user wasn’t known, or the wrong password was supplied.
timeouts Number of times each server did not respond.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 241

242 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Chapter 37

rarpd Command

The show rarpd command displays information about the X-Pedition’s Reverse Address
Resolution Protocol (RARP) configuration.

Format
show rarpd interface| mappings

Mode
Privileged

Description
The show rarpd command displays information about the configuration of the X-
Pedition’s RARP server. You may list the MAC-to-IP address mappings or the interfaces
to which the X-Pedition responds to RARP requests.

Parameters
interface Lists the interfaces to which the X-Pedition responds to RARP requests.
mappings Displays the list of MAC-to-IP address mappings.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 243

Example
To display the RARP server’s list of MAC-to-IP address mappings:

xp# show rarpd mappings

244 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 38

rate-limit Command

The show rate-limit command displays rate limiting policies.

There are three different types of rate limiting supported:
• flow rate limiting: rate limiting for individual flows
• aggregate rate limiting: rate limiting for an aggregation of flows
• port level rate limiting: rate limiting for individual ports

Format
show rate-limit [all] | [policy-type flow-policies| aggregate-policies| portlevel-policies|
all] | [policy-name <name>] | [interface <interface>] | [port-level port <port list>|
all-port] | [port-level policy-name <name>] | [rate-limiting-mode]

Mode
Privileged

Description
The show rate-limit command displays information about rate limiting policies.

Parameters
all Displays information on all rate limit policies configured on the X-Pedition.
policy-type
The type of the rate limit policy. The keyword all shows all rate limit types. You can
specify the following types of policies:
flow-policies All flow policies

Enterasys X-Pedition Common Command Line Interface Reference Manual 245

 aggregate-policies All aggregate policies
portlevel-policies All port level policies
all All policies
policy-name <name>| all
The name of the rate limiting policy. The keyword all shows all rate limit policies.
interface <interface>| all
The name of the IP interface. The keyword all shows rate limiting policies for all IP
interfaces.
port-level port <port list>| all-ports
The name of the port. The keyword all-ports shows rate limiting policies for all
ports.
port-level policy-name <name>
The name of the rate limiting policy name.
rate-limiting-mode
Displays the current rate limiting mode, whether per-flow rate limiting or aggregate
rate limiting.

Restrictions
None.

246 Enterasys X-Pedition Common Command Line Interface Reference Manual

Example
To display all configured rate limit policies:

xp# show rate-limit all

--------------------------------------------------------------------------
Rate Limit Policy name : rlpol 1
Applied Interfaces : if0 2

3 4 5 6 7 8 9
ACL Source IP/Mask Dest. IP/Mask SrcPort DstPort TOS Prot
--- -------------- ------------- --------- --------- ---- ---
100 10.212.10.11/32 anywhere any any any IP
200 10.212.10.12/32 anywhere any any any IP
300 10.212.10.13/32 anywhere any any any IP
400 10.212.10.14/32 anywhere any any any IP
500 10.212.10.10/32 anywhere any any any IP

10 11 12 13
Seq ACL Rate Limit Exceed Action
--- ---- -------- -------------
10 100 26000 Low
10 200 26000 Low
10 300 26000 Low
10 400 26000 Low
10 500 26000 Low

Legend:
1. The name of the rate limit.
2. The IP interface to which the rate limit is applied.
3. The name of the ACL(s) that define the rate limit.
4. The source address and filtering mask specified by the ACL.
5. The destination address and filtering mask specified by the ACL.
6. The number of the TCP or UDP source port.
7. The number of the TCP or UDP destination port.
8. The Type of Service value.
9. The protocol for the ACL.
10. The sequence number for this policy.
11. The name of the ACL.
12. The rate limit for the flow.

Enterasys X-Pedition Common Command Line Interface Reference Manual 247

 13. The action to be taken if the rate limit is reached: packets can be dropped or the
priority set to low, medium, or high.

248 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 39

reload Command

The reload command reboots the X-Pedition.

Format
reload

Mode
Privileged

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 249

250 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Command Summary

Chapter 40

rip Commands

The Routing Information Protocol, Version 1 and Version 2 (RIPv1 and RIPv2), is the
most commonly used interior gateway protocol. RIP selects the route with the lowest
metric as the best route. The metric is a hop count representing the number of gateways
through which data must pass in order to reach its destination. The longest path that RIP
accepts is 15 hops. If the metric is greater than 15, a destination is considered unreachable
and the X-Pedition discards the route. RIP assumes that the best route is the one that uses
the fewest gateways, that is, the shortest path. RIPv1 is described in RFC 1058 and RIPv2
is described in RFC 1723.
The rip commands allow the user to display various information about the RIP.

Command Summary
Table 28 lists the rip commands. The sections following the table describe the command
syntax.

Table 28. rip commands

rip trace [packets| request| response| local options] [detail] [send| receive]
show rip <option list>

Enterasys X-Pedition Common Command Line Interface Reference Manual 251

rip trace

rip trace

Purpose
Traces RIP packets.

Format
rip trace [packets| request| response| local-options] [detail| send| receive]

Mode
Privileged

Description
The rip trace command traces the following sets of RIP packets:
• RIP request packets sent or received by the X-Pedition
• RIP response packets sent or received by the X-Pedition
Depending on the options you specify, you may trace all packets, request packets only, or
receive packets only. In addition, you may choose to trace the request packets, receive
packets, or both that are sent by the X-Pedition, received by the X-Pedition, or all packets
(both sent packets and received packets).

Parameters
packets Traces all RIP packets, both request packets and response packets. This is the
default.
request Traces only request packets, such as REQUEST, POLL and POLLENTRY
packets.
response Traces only response packets.
For the packets, request, and response parameters, you may optionally specify one of the
following:
detail Shows detailed information about the traced packets.
send Shows information about traced RIP packets sent by the X-Pedition.
receive Shows information about traced RIP packets received by the X-Pedition.
Note: The default shows both send and receive packets.

252 Enterasys X-Pedition Common Command Line Interface Reference Manual

 rip trace

local-options Sets trace options for this protocol only. Specify one or more of the
following:
all Turns on all tracing.
general Turns on normal and route tracing.
state Traces state machine transitions in the protocols.
normal Traces normal protocol occurrences.
Note: Abnormal protocol occurrences are always traced.
policy Traces application of protocol and user-specified policies to
routes being imported and exported.
task Traces system processing associated with this protocol or peer.
timer Traces timer usage by this protocol or peer.
route Traces routing table changes for routes installed by this
protocol or peer.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 253

show rip

show rip

Purpose
Displays RIP information.

Format
show rip <option-list>

Mode
Privileged

Description
The show rip command displays RIP information.

Parameters
<option-list>
Specifies the RIP dump information you want to display. Specify one or more of the
following:
all
Displays all RIP tables.
globals
Displays RIP globals.
timers
Displays RIP timers.
interface
Displays RIP interfaces.
active-gateways
Displays active gateways running RIP.
interface-policies
Displays RIP interface policies.
import-policies
Displays RIP import policies.

254 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show rip

export-policies
Displays RIP export policies.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 255

show rip

256 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 41

rmon Commands

The rmon commands allow the user to display and set parameters for Remote Network
Monitor (RMON) device statistics on a per-port basis. RMON information corresponds to
RFCs 1757 and 2021.

Command Summary
Table 29 lists the rmon commands. The sections following the table describe the command
syntax.

Table 29. rmon commands

clear rmon cli-filter

clear rmon statistics
rmon apply cli-filter <filter-id>
show rmon [alarms| events| filter| history| matrix| packet-capture| status]

Enterasys X-Pedition Common Command Line Interface Reference Manual 257

clear rmon cli-filter

clear rmon cli-filter

Purpose
Clears currently-selected CLI RMON filters.

Format
clear rmon cli-filter

Mode
Privileged

Description
The clear rmon cli-filter command clears the CLI RMON filters that were applied with
the rmon apply cli-filter command.

Parameters
None.

Restrictions
None.

258 Enterasys X-Pedition Common Command Line Interface Reference Manual

 clear rmon statistics

clear rmon statistics

Purpose
Clears RMON statistics.

Format
clear rmon statistics

Mode
Privileged

Description
The clear rmon statistics command clears RMON statistics for all X-Pedition ports.
When you clear statistics, the X-Pedition sets the counters for the cleared statistics to 0,
then begins accumulating the statistics again.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 259

rmon apply cli-filter

rmon apply cli-filter

Purpose
Applies a specific CLI RMON filter.

Format
rmon apply cli-filter <filter-id>

Mode
Privileged

Description
The rmon apply cli-filter command applies a specific CLI RMON filter to the current
Telnet or Console session. This enables different users to select the different CLI filters.
Use the rmon clear cli-filter command to clear an applied filter.

Parameter
<filter id> This is a number between 1 and 65535 which identifies the filter ID to
apply.

Restrictions
None.

Example
To apply filter ID 2:

xp# rmon apply cli-filter 2

260 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show rmon

show rmon

Purpose
Displays statistics related to various RMON parameters.

Format
show rmon [alarms| events| filters| history| matrix| packet-capture| status]

Mode
Privileged

Description
The show rmon command displays statistics related to various RMON parameters.

Parameters
alarms Displays the RMON Alarm table.
events Displays configured events and the logs, if any, of triggered events.
filters Displays the contents of the Filter table.
history Displays statistical samples that are stored in the RMON History
group. Entries in this table are created automatically when default
tables are turned on for the Lite group.
matrix Displays entries in the Matrix table. Entries in this table are
automatically created when default tables are turned on for the
Standard group.
Note: If CLI filters have been applied, they will take effect when the
Matrix table is displayed. This command will display control rows and their
corresponding logs only if there are logs. A control row that has no data is
not displayed.

packet-capture Displays the buffer table for captured packets.

status Displays RMON 1 and II status and memory information.

Enterasys X-Pedition Common Command Line Interface Reference Manual 261

show rmon

262 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 42

sfs Commands

The sfs commands display Cabletron Discovery Protocol (CDP) parameters

Command Summary
Table 30 lists the sfs commands. The sections following the table describe the command
syntax.

Table 30. sfs commands

show sfs cdp-hello- port-status <port-list>| all-ports

show sfs cdp-hello transmit-frequency

Enterasys X-Pedition Common Command Line Interface Reference Manual 263

show sfs cdp-hello port-status

show sfs cdp-hello port-status

Purpose
Displays CDP Hello status of a port.

Format
show sfs cdp-hello port-status <port-list>| all-ports

Mode
Privileged

Description
The show sfs cdp-hello port-status command displays CDP Hello information of X-
Pedition ports.

Parameters
<port-list>| all-ports Specifies the ports for which you want to display information. The
all-ports keyword displays the selected information for all the X-
Pedition ports.

Restrictions
None.

Examples
To display CDP Hello status on all X-Pedition ports:

xp# show sfs cdp-hello port-status all-ports

264 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show sfs cdp-hello transmit-frequency

show sfs cdp-hello transmit-frequency

Purpose
Displays the transmit frequency of CDP Hello packets.

Format
show sfs cdp-hello transmit-frequency

Mode
Privileged

Description
The show sfs cdp-hello transmit-frequency command display the transmit frequency of
CDP Hello packets on the X-Pedition.

Parameters
None.

Restrictions
None.

Examples
To display the transmit frequency of CDP Hello packets:

xp# show sfs cdp-hello transmit-frequency

Enterasys X-Pedition Common Command Line Interface Reference Manual 265

show sfs cdp-hello transmit-frequency

266 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 43

smarttrunk Commands

The smarttrunk commands allow the user to display parameters for SmartTRUNK
ports. SmartTRUNK ports are groups of ports that have been logically combined to
increase throughput and provide link redundancy.

Command Summary
Table 31 lists the smarttrunk commands. The sections following the table describe the
command syntax.

Table 31. smarttrunk commands

clear smarttrunk load-distribution <num>

show smarttrunk [distribution| protocol-state| connections] <numlist>

Enterasys X-Pedition Common Command Line Interface Reference Manual 267

clear smarttrunk load-distribution

clear smarttrunk load-distribution

Purpose
Clears load distribution statistics for ports in a SmartTRUNK.

Format
clear smarttrunk load-distribution <num>

Mode
Privileged

Description
The clear smarttrunk load-distribution command is used in conjunction with the
show smarttrunk distribution command, which gathers statistics for the transmitted
bytes per second flowing through the SmartTRUNK and each port in it. The clear
smarttrunk load-distribution command lets you reset load distribution statistics to
zero.

Parameters
<num> Specifies name of one or more existing SmartTRUNKs.

Restrictions
None.

Example
To clear load distribution information from SmartTRUNK st.1:

xp# clear smarttrunk load-distribution st.1

268 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show smarttrunk

show smarttrunk

Purpose
Displays information about SmartTRUNKs on the X-Pedition

Format
show smarttrunk [distribution| protocol-state| connections] <numlist>

Mode
Privileged

Description
The show smarttrunk command displays statistics about SmartTRUNKs on the X-
Pedition.

Parameters
distribution Provides statistics on how traffic is distributed across the ports in
a SmartTRUNK.
protocol-state Shows information about the control protocol on a
SmartTRUNK.
connections Shows information about the SmartTRUNK connection,
including the MAC address of the remote switch, and the module
number and port number of each remote port. Connection
information is reported only if the Hunt Group protocol is
enabled for the SmartTRUNK.
<numlist > Specifies name of one or more SmartTRUNKs.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 269

show smarttrunk

Examples
To show how traffic is distributed across the ports on all SmartTRUNKs:

xp# show smarttrunk distribution

SmartTRUNK Member % Link Utilization Link Status Grp Status

---------- ------ ------------------ ----------- ----------
st.1 et.2.4 0.00 Forwarding Up
st.1 et.2.5 0.00 Forwarding Up
st.1 et.2.6 0.00 Forwarding Up

To show information about the control protocol for SmartTRUNK st.1:

xp# show smarttrunk protocol-state st.1

SmartTRUNK Protocol State Port Port State

---------- -------- ----- ---- ----------
st.1 HuntGroup Down et.3.1 Negotiate
et.3.2 Negotiate

To show connection information for all SmartTRUNKs:

xp# show smarttrunk connections

SmartTRUNK Local Port Remote Switch Remote Module Remote Port State
---------- ---------- ------------- ------------- ----------- -----
st.1 ether2/1 Enterasys A9:6E:57 3 1 Up
st.1 ether2/2 Enterasys A9:6E:57 3 2 Up
st.1 ether2/3 Enterasys A9:6E:57 3 3 Up
st.1 giga3/1 Enterasys A9:6E:57 4 5 Up
st.2 ether2/4 -- -- -- Up
st.2 ether2/5 -- -- -- Up
st.2 ether2/6 -- -- -- Up

Note: In the example above, SmartTRUNK st.2 has no control protocol enabled, so no
connection information is reported.

270 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 44

snmp Commands

The snmp commands allow the user to display and test parameters for Simple Network
Management Protocol (SNMP).

Command Summary
Table 32 lists the snmp commands. The sections following the table describe the command
syntax.

Table 32. snmp commands

show snmp access| chassis-id| community| mibs| statistics| tfpt| trap

snmp test trap type coldstart| linkdown| linkup| ps-failure| ps-recover |
vrrpnewmaster

Enterasys X-Pedition Common Command Line Interface Reference Manual 271

show snmp

show snmp

Purpose
Allows the user to display SNMP parameters, including SNMP community names.

Format
show snmp access| chassis-id| community| mibs| statistics| tfpt| trap

Mode
Privileged

Description
The show snmp command displays the following SNMP information:
• Community strings set on the X-Pedition
• SNMP Statistics
• IP address of SNMP trap target server

Parameters
access Displays the last five SNMP clients to access the X-Pedition.
chassis-id Displays the X-Pedition’s SNMP name.
tftp Displays tftp SNMP status.
trap Displays the IP address of the trap target server.
community Displays the X-Pedition’s community string.
statistics Displays SNMP statistics.
mibs Displays the SNMP MIB registry.

Restrictions
None.

272 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show snmp

Examples
The following command displays a log of SNMP access to the X-Pedition. The host that
accessed the X-Pedition and the X-Pedition system time when the access occurred are
listed.

xp# snmp show access

SNMP Last 5 Clients:
10.15.1.2 Wed Feb 10 18:42:59 1999
10.15.1.2 Wed Feb 10 18:42:55 1999
10.15.1.2 Wed Feb 10 18:42:56 1999
10.15.1.2 Wed Feb 10 18:42:57 1999
10.15.1.2 Wed Feb 10 18:42:58 1999

To display the SNMP identity of the X-Pedition:

xp# snmp show chassis-id

SNMP Chassis Identity:

s/n 123456

To display the IP address of the trap target server:

xp# snmp show trap

Trap Table:
Index Trap Target Addr Community String Status
1. 10.15.1.2 public enabled
2. 1.2.3.4 public123 disabled
3. 5.6.7.8 public20 disabled

Enterasys X-Pedition Common Command Line Interface Reference Manual 273

snmp test trap

snmp test trap

Purpose
Tests SNMPv1 notifications to currently configured managers.

Format
snmp test trap type coldstart| linkdown| linkup| ps-failure| ps-recover|
vrrpnewmaster

Mode
Privileged

Description
The snmp test trap command allows the user to test SNMPv1 notifications to currently
configured managers. The user may test the following notification types:
• Coldstart
• Linkdown
• Linkup
• PS-failure
• PS-recover
• VRRPNewMaster

Parameters
coldstart Tests the cold start trap notification.
linkdown Tests link down notification for ifIndex 1.
linkup Tests link up notification for ifIndex 1.
ps-failure Tests the power supply failure trap notification.
ps-recover Tests the power supply recover trap notification.
vrrpNewMasterTests the Virtual Router Redundancy New Master Trap.

274 Enterasys X-Pedition Common Command Line Interface Reference Manual

 snmp test trap

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 275

snmp test trap

276 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 45

sonet Commands

The sonet commands allows the user to display various parameters for Synchronous
Optical Network (SONET) encapsulation. These commands also allow the user to
accommodate Packet-over-SONET (POS) and ATM (Asynchronous Transfer Mode)
transmission using the X-Pedition.
Packet-over-SONET technology provides the ability to transmit IP packets and ATM cells
over a SONET backbone by encapsulating them into a SONET frame. In reference to the
OSI Layer model, the SONET layer rests right beneath the IP layer or the ATM layer.
Based on the transmission mechanism of SONET frames, the result is larger traffic
bandwidth and faster line speed (OC-3), accommodating QoS guarantees as well as the
ability to deliver voice/video data over an internetwork.
SONET frames carry a large amount of data stored as overhead. This overhead
information provide the information for OAM&P (operation, administration,
management, and provisioning) capabilities, such as performance monitoring, automatic
protection switching, and path tracing.
Enterasys SONET technology features Automatic Protection Switching, performance
monitoring capabilities, as well as commercial circuit identification.

Enterasys X-Pedition Common Command Line Interface Reference Manual 277

Command Summary

Command Summary
Table 33 lists the sonet commands. The sections following the table describe the command
syntax.

Table 33. sonet commands

show sonet aps <SONETports>

show sonet loopback <SONETports>
show sonet medium <SONETports>
show sonet pathtrace <SONETports>

278 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show sonet aps

show sonet aps

Purpose
Displays APS status.

Format
show sonet aps <SONETports>

Mode
Privileged

Description
The show sonet aps command allows the user to display APS (Automatic Protection
Switching) status. This command allows you to display such APS parameters as
protection level, working or protecting port, directionality, and switch status.

Parameters
<SONETports> Specifies the SONET port name(s).

Restrictions
None.

Example
To display the APS status for port so.2.1:

xp# show sonet aps so.2.1

Enterasys X-Pedition Common Command Line Interface Reference Manual 279

show sonet loopback

show sonet loopback

Purpose
Displays loopback status.

Format
show sonet loopback <SONETports>

Mode
Privileged

Description
The show sonet loopback command allows the user to display loopback status for a
specified SONET port. Loopback is used to verify connectivity between two devices.

Parameters
<SONETports> Specifies the SONET port name(s).

Restrictions
None.

Example
To display the loopback status for port so.2.1:

xp# show sonet loopback so.2.1

280 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show sonet medium

show sonet medium

Purpose
Displays SONET optical line values.

Format
show sonet medium <SONET ports>

Mode
Privileged

Description
The show sonet medium command allows the user to display the various SONET optical
line values associated with a SONET port. This command will allow you to display values
such as framing status, line type, and administrator-specified circuit identifier.

Parameters
<SONETports> Specifies the SONET port name(s).

Restrictions
None.

Example
To display optical line values for port so.2.1:

xp# show sonet medium so.2.1

Enterasys X-Pedition Common Command Line Interface Reference Manual 281

show sonet pathtrace

show sonet pathtrace

Purpose
Displays received path trace messages.

Format
show sonet pathtrace <SONETports>

Mode
Privileged

Description
The show sonet pathtrace command allows the user to display path trace messages
received on a specified SONET port.

Parameters
<SONETports> Specifies the SONET port name(s).

Restrictions
None.

Example
To display the path trace messages for port so.2.1:

xp# show sonet pathtrace so.2.1

282 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Command Summary

Chapter 46

statistics Commands

The statistics commands allow the user to display statistics for various X-Pedition
features. The user may also clear some statistics.

Command Summary
Table 34 lists the statistics commands. The sections following the table describe the
command syntax.

Table 34. statistics commands

clear interface [<port-list>] [errors|packets|statistics]

clear ip statistics
clear ipx statistics
show ip icmp statistics
show ip multicast
show ip traffic
show ipx traffic
show port errors [<port-list>]
show port packets [<port-list>]
show port stats [<port-list>]
show processes cpu
show rarp [<IFname>]

Enterasys X-Pedition Common Command Line Interface Reference Manual 283

Command Summary

Table 34. statistics commands (Continued)

show tcp statistics

show traffic
show udp statistics

284 Enterasys X-Pedition Common Command Line Interface Reference Manual

 clear interface

clear interface

Purpose
Clears various statistics.

Format
clear interface [<port-list>] [errors|packets|statistics]

Mode
Privileged

Description
The clear interface command clears port statistics, error statistics, or RMON statistics.
When you clear statistics, the X-Pedition sets the counters for the cleared statistics to 0,
then begins accumulating the statistics again.

Parameters
<port-list>
The ports for which you are clearing statistics. You can specify a single port or a
comma-separated list of ports. Example: ethernet1/3,ethernet.(1-3).(4,6-8). If no port
is specified, the clear interface command will clear statistics for all X-Pedition ports.
errors Clears all error statistics for the specified port.
packets Clears all packet statistics for the specified port.
statistics Clears all normal (non-error) statistics for the specified port.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 285

clear ip statistics

clear ip statistics

Purpose
Clears Internet Protocol (IP) statistics.

Format
clear ip statistics

Mode
Privileged

Description
The clear ip statistics command clears IP statistics for all X-Pedition ports. When you
clear statistics, the X-Pedition sets the counters for the cleared statistics to 0, then begins
accumulating the statistics again.

Parameters
None.

Restrictions
None.

286 Enterasys X-Pedition Common Command Line Interface Reference Manual

 clear ipx statistics

clear ipx statistics

Purpose
Clears IPX statistics.

Format
clear ipx statistics

Mode
Privileged

Description
The clear ipx statistics command clears IPX statistics for all X-Pedition ports. When you
clear statistics, the X-Pedition sets the counters for the cleared statistics to 0, then begins
accumulating the statistics again.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 287

show ip icmp statistics

show ip icmp statistics

Purpose
Displays internet control message protocol (ICMP) statistics.

Format
show ip icmp statistics

Mode
Privileged

Parameters
None.

Restrictions
None.

Example
To display ICMP statistics:

xp# show ip icmp statistics

icmp:
0 messages with bad code fields
0 messages smaller than minimum length
0 bad checksums
0 messages with bad length
0 message responses generated

• messages with bad code fields Displays the number of ICMP messages
processed by the router with a bad code field. The
code field within the ICMP header uses a number
to specify the message content of the ICMP
message. An invalid number within the code field
would show in this statistic parameter.

288 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip icmp statistics

• messages smaller than min length Displays the number of ICMP messages
processed by the router that didn’t meet a
minimum length requirement.

• bad checksums Displays the number of ICMP messages

processed by the router with bad checksums. The
checksum field within the ICMP header is used to
verify that the message was transmitted error-
free. A bad checksum indicates an ICMP message
with errors.

• messages with bad length Displays the number of ICMP messages

processed by the router with bad or invalid length.

• message responses generated Displays the number of ICMP responses that have
been generated by the router in response to ICMP
messages.

Enterasys X-Pedition Common Command Line Interface Reference Manual 289

show ip multicast

show ip multicast

Purpose
Displays multicast statistics.

Format
show ip multicast

Mode
Privileged

Parameters
None.

Restrictions
None.

Example
To display multicast statistics:

xp# show ip multicast

multicast forwarding:
0 multicast forwarding cache lookups
0 multicast forwarding cache misses
0 upcalls to mrouted
0 upcall queue overflows
0 upcalls dropped due to full socket buffer
0 cache cleanups
0 datagrams with no route for origin
0 datagrams arrived with bad tunneling
0 datagrams could not be tunneled
0 datagrams arrived on wrong interface
0 datagrams selectively dropped
0 datagrams dropped due to queue overflow
0 datagrams dropped for being too large

290 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip traffic

show ip traffic

Purpose
Displays Internet Protocol (IP) and unicast IP routing statistics.

Format
show ip traffic

Mode
Privileged

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 291

show ip traffic

Example
To display IP and IP routing statistics:

xp# show ip traffic

ip:
78564 total packets received
0 bad header checksums
0 packets with size smaller than minimum
0 packets with data size < data length
0 packets with header length < data size
0 packets with data length < header length
0 packets with bad options
0 packets with incorrect version number
0 fragments received
0 fragments dropped (dup or out of space)
0 fragments dropped after timeout
0 packets reassembled ok
2984 packets for this host
0 packets for unknown/unsupported protocol
0 packets forwarded
75580 packets not forwardable
0 redirects sent
2120 packets sent from this host
0 packets sent with fabricated ip header
0 output packets dropped due to no bufs, etc.
0 output packets discarded due to no route
0 output datagrams fragmented
0 fragments created
0 datagrams that can't be fragmented
routing:
0 bad routing redirects
0 dynamically created routes
0 new gateways due to redirects
1141 destinations found unreachable
0 uses of a wildcard route

IP Statistics:

• total packets received Displays the total number of IP packets received

by the router, including all forwarded and
dropped packets.

• bad header checksums Displays the number of IP packets received by the

router with bad checksums. The checksum
field within the IP header is used to verify that
the packet was transmitted error-free. A bad
checksum indicates an IP packet with errors.

292 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip traffic

• packets w/size smaller than min Displays the number of IP packets received by the
router that didn’t meet a minimum length
requirement.

• packets w/data size<data length Displays the number of IP packets received by the
router containing a data size smaller than the
specified data length. The data length field in
the IP header specifies the data length
contained within the packet.

• packets w/header length<data size Displays the number of IP packets received by the
router containing a IP header length smaller
than the data size within the packet.

• packets w/data length<header length Displays the number of IP packets received by the
router containing a data length smaller than
the IP header length.

• packets w/incorrect version number Displays the number of IP packets received by the
router with an incorrect IP version number.
The IP version number field in the IP header
is used to specify whether the packet is
formatted for IPv4 or IPv6.

• fragments received Displays the number of datagram fragments

received by the router. A datagram that does
not fit into an IP packet must be fragmented
into two or more packets.

• fragments dropped Displays the number of datagram fragments

dropped by the router. A datagram that does
not fit into an IP packet must be fragmented
into two or more packets.

• fragments dropped after timeout Displays the number of datagram fragments

dropped by the router after a certain time
period. A datagram that does not fit into an IP
packet must be fragmented into two or more
packets.

• packets reassembled ok Displays the number of IP packets containing

fragmented datagrams that were reassembled
successfully at the destination.

• packets for this host Displays the total number of IP packets received
that were intended for the router as the
destination.

Enterasys X-Pedition Common Command Line Interface Reference Manual 293

show ip traffic

• packets for unknown protocol Displays the number of IP packets received by the
router that is of an unknown or unsupported
routed protocol.

• packets forwarded Displays the number of IP packets received by the

router that were forwarded onto another host.

• packets not forwardable Displays the total number of IP packets received

by the router that could not be forwarded onto
another host.

• redirects sent Displays the number of redirects sent by the

router.

• packets sent from this host Displays the total number of IP packets sent out
by the router.

• packets sent w/fabricated ip header Displays the total number of IP packets sent out
by the router after attaching an IP header onto
the packet.

• output packets dropped due to no bufsDisplays the total number of IP packets dropped
before being sent out by the router because of
lack of output buffer space.

• output packets discarded due to no routeDisplays the total number of IP packets

dropped before being sent out by the router
because of no IP routing information.

• output datagrams fragmented Displays the total number of datagrams that were
fragmented into two or more IP packets
before being sent out by the router.

• fragments created Displays the total number of datagram fragments

created.

• datagrams that can’t be fragmented Displays the total number of datagrams that was
not successfully fragmented into two or more
IP packets.
Routing Statistics:

• bad routing redirects Displays the number of bad redirects have

occurred. A redirect occurs in the case where the
destination interface is the same as the source
interface.

294 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip traffic

• dynamically created routes Displays the number of IP routes have been

created using a routing protocol, as opposed to
static routes which are user-defined.

• new gateways due to redirects Displays the number of new gateways have been
added into the routing table due to redirects.

• destinations found unreachable Displays the number of destination addresses that

have been found to be unreachable in the routing
table. A destination may be unreachable due to
the route being expired or being unavailable due
to network changes.

• uses of a wildcard route Displays the number of times that a wildcard

route has been used to forward a packet onto the
next-hop destination.

Enterasys X-Pedition Common Command Line Interface Reference Manual 295

show ipx traffic

show ipx traffic

Purpose
Displays internetwork packet exchange (IPX) and IPX routing statistics.

Format
show ipx traffic

Mode
Privileged

Parameters
None.

Restrictions
None.

296 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ipx traffic

Example
To display IPX statistics:

xp# statistics show ipx

ipx:
0 total packets received
0 packets with bad checksums
0 packets smaller than advertised
0 packets smaller than a header
0 packets forwarded
0 packets not forwardable
0 packets for this host
0 packets sent from this host
0 packets dropped due to no bufs, etc.
0 packets discarded due to no route
0 packets too big
0 packets with too many hops
0 packets of type 20
0 packets discarded due to infiltering
0 packets discarded due to outfiltering
0 packets with misc protocol errors
0 rip packets discarded due to socket buffer full
0 sap packets discarded due to socket buffer full
0 rip req packets discarded due to socket buffer full
0 sap gns packets discarded due to socket buffer full
0 packets discarded due to port of entry zero
0 packets discarded due to sourced by us
routing:
0 bad routing redirects
0 dynamically created routes
0 new gateways due to redirects
1141 destinations found unreachable
0 uses of a wildcard route

Enterasys X-Pedition Common Command Line Interface Reference Manual 297

show port errors

show port errors

Purpose
Displays port error statistics.

Format
show port errors [<port-list>]

Mode
Privileged

Parameters
<port-list> Specifies the port. If no port is specified, command will display port error
statistics for all physical and logical ports.

Restrictions
None.

298 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port errors

Example
To display port error statistics on port ethernet2/1:

xp# show port errors ethernet2/1

Port: et.2.1
----
Error Stats Error Stats

----------- -----------

CRC errors 0 Carrier sense errors 0

Single collision (tx OK) 0 Many collisions (tx OK) 0

Many collisions (drop) 0 Late collisions 0

Long frames >1518 bytes 0 Invalid long frames 0

Short frames <64 bytes 0 Alignment errors 0

Deferred transmissions 0 Transmit underruns 0

IP - bad version 0 IP - bad checksum 0

IP - bad header 0 IP - small datagram 0

IP - expand TTL ring 0 IPX - bad header 0

Non-IP/IPX protocol 0 Invalid MAC encap. 0

Internal frame tx error 0 Internal frame rx error 0

Input buffer overflow 0 Packet request overflow 0

Out buffer (low) ovflow 0 Out buffer (med) ovflow 0

Out buffer (high) ovflow 0 Out buffer (ctrl) ovflow 0

Input VLAN drop frame 0

Error stats cleared * Never Cleared *

Enterasys X-Pedition Common Command Line Interface Reference Manual 299

show port packets

show port packets

Purpose
Displays port packet statistics.

Format
show port packets [<port-list>]

Mode
Privileged

Parameters
<port-list> Specifies the port. If no port is specified, command will display port
packet statistics for all physical and logical ports.

Restrictions
None.

300 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port packets

Example
To display port packet statistics on port et.2.1:

xp# show port packets et.2.1

Port: et.2.1
----
RMON Stats Received Transmitted

---------- -------- -----------

Unicast frames 0 0

Multicast frames 0 0

Broadcast frames 0 0

64 byte frames 0 0

65-127 byte frames 0 0

128-255 byte frames 0 0

256-511 byte frames 0 0

512-1023 byte frames 0 0

1024-1518 byte frames 0 0

RMON stats cleared * Never Cleared *

Enterasys X-Pedition Common Command Line Interface Reference Manual 301

show port stats

show port stats

Purpose
Displays normal (non-error) port statistics.

Format
show port stats [<port-list>]

Mode
Privileged

Parameters
<port-list> Specifies the port. If no port specified, command will display port
statistics for all physical and logical ports.

Restrictions
None.

302 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port stats

Example
To display port statistics on port et.2.1:

xp# show port stats et.2.1

Port: et.2.1
-------------
Port Stats Received Transmitted

---------- -------- -----------

Frames/Packets 0 0

. Switched frames (bridging) 0 0

. Local frames (bridging) 0 N/A

. Routed packets 0 0

. Switched (data) 0 N/A

. Consumed by CPU 0 N/A
Bytes 0 0

. Bridged bytes 0 0

. Routed bytes 0 0

L2 table misses 0 N/A

IP table misses 0 N/A
IPX table misses 0 N/A
IP TTL expirations 0 N/A
IPX TC expirations 0 N/A
1 minute traffic rates
. Average bits/sec 0 0

. Packet discards 0 0

. Packet errors 0 0

. Unicast packets 0 0

. Multicast packets 0 0

. Broadcast packets 0 0

Port stats cleared * Never Cleared *

• Frames/Packets

• Switched framesShows the number of frames that have been bridged or forwarded.

Enterasys X-Pedition Common Command Line Interface Reference Manual 303

show port stats

• Local framesShows the number of local frames (frames destined for a port that is the
same as the port of entry) that was dropped.

• Routed packets

• Switched (data)Shows the number of packets that was forwarded by the hardware.

• Consumed by CPUShows the number of packets that was sent to the control module
to be forwarded.

• Bytes

• Bridged bytesShows the number of total bytes that has been bridged.

• Routed bytesShows the number of total bytes that has been routed.

• L2 table misses Shows the number of times that a Layer-2 frame

could not be resolved by the L2 Table.

• IP table misses Shows the number of times that an IP packet

could not be resolved by the IP Routing Table.

• IPX table misses Shows the number of times that an IPX packet
could not be resolved by the IPX Routing Table.

• IP TTL expirations Shows the number of IP packets that have been

received by the port with a Time-to-Live (TTL)
header with a value of 1. The IP packet will then
be expired at this point.

• IPX TC expirations Shows the number of IPX packets that have been
received by the port with a TC header with a value
of 1. The IPX packet will then be expired at this
point.

• 1 minute traffic rates

• Average bits/secShows an average traffic rate in bits/second for a one-minute time

period for a port.

• Packet discardsShows the number of packets discarded by a port within a one-minute

time period.

• Packet errorsShows the number of packets containing errors that was seen by the port
within a one-minute time period.

• Unicast packetsShows the number of unicast packets that was seen by the port within
a one-minute time period.

304 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show port stats

• Multicast packetsShows the number of multicast packets that was seen by the port
within a one-minute time period.

• Broadcast packetsShows the number of broadcast packets that was seen by the port
within a one-minute time period.

• Port stats Cleared Shows the date and time when the port stats were
last cleared.

Enterasys X-Pedition Common Command Line Interface Reference Manual 305

show processes cpu

show processes cpu

Purpose
Displays active tasks.

Format
show processes cpu

Mode
Privileged

Parameters
None.

Restrictions
None.

306 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show processes cpu

Example
To display active tasks:

xp# show processes cpu

Timestamp: 2000-04-25 17:56:32

CPU Idle : 98% (since system startup 441751425.0 sec ago)
NAME USAGE % RELATIVE %
-------- ------- ----------
STP_T 0.2 47.65
PHY_POLL 0.0 17.57
L2_AGE_T 0.0 7.90
L3_AGE_T 0.0 7.10
IPC 0.0 4.60
CONS_T 0.0 4.25
STATS_T 0.0 3.96
TNTASK 0.0 2.41
SYSTEM H 0.0 0.88
HBT_T 0.0 0.82
SNMP 0.0 0.67
GATED 0.0 0.58
IPXROUTE 0.0 0.48
CONS2T 0.0 0.33
LOWEST 0.0 0.25
PPP_TASK 0.0 0.24
PINGER_T 0.0 0.11
L2_LRN_T 0.0 0.07
CDP_T 0.0 0.02
LFAP_CN 0.0 0.00
LGRP_T 0.0 0.00
MPS 0.0 0.00
TNETD 0.0 0.00
ETHH 0.0 0.00
NI H 0.0 0.00
ARP_T 0.0 0.00
HSWAP 0.0 0.00
IPRED_T 0.0 0.00
SYS_TK 0.0 0.00
SNMP_CF 0.0 0.00
WAN_TOD_ 0.0 0.00
DHCP 0.0 0.00
BOUNCE 0.0 0.00
IP_T 0.0 0.00
IPX_T 0.0 0.00
PHX_T 0.0 0.00
NTP 0.0 0.00
ERROR_LO 0.0 0.00
L3_ACL_T 0.0 0.00
MCAST 0.0 0.00
PROFILE 0.0 0.00
PRI_L3MD 0.0 0.00
L3_RL_T 0.0 0.00

Enterasys X-Pedition Common Command Line Interface Reference Manual 307

show rarp

show rarp

Purpose
Displays reverse ARP statistics.

Format
show rarp [<IFname>]

Mode
Privileged

Parameters
<IFname> Specifies the interface name. If no interface name specified, command
will display reverse ARP statistics for all interfaces.

Restrictions
None.

Example
To display reverse ARP statistics on interface ‘en0’:

xp# show rarp en0

Interface en0:
0 requests received
0 replies sent
0 requests received on interface with rarpd disabled
0 requests received that failed sanity check
0 requests received that did not result in a match
Last 5 Requests Received
----- no rarp requests received -----
Last 5 Replies Sent
----- no rarp replies sent -----

308 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show tcp statistics

show tcp statistics

Purpose
Displays Transmission Control Protocol (TCP) statistics.

Format
show tcp statistics

Mode
Privileged

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 309

show tcp statistics

Example
To display TCP statistics:

xp# show tcp statistics

tcp:
235 packets sent
232 data packets (22777 bytes)
1 data packet (494 bytes) retransmitted
0 resends initiated by MTU discovery
2 ack-only packets (5 packets delayed)
0 URG only packets
0 window probe packets
0 window update packets
0 control packets
320 packets received
227 acks (for 22776 bytes)
3 duplicate acks
0 acks for unsent data
158 packets (185 bytes) received in-sequence
0 completely duplicate packets (0 bytes)
0 old duplicate packets
0 packets with some dup. data (0 bytes duped)
0 out-of-order packets (0 bytes)
0 packets (0 bytes) of data after window
0 window probes
0 window update packets
0 packets received after close
0 discarded for bad checksums
0 discarded for bad header offset fields
0 discarded because packets too short
0 connection requests
1 connection accept
1 bad connection attempt
0 listen queue overflows
1 connection established (including accepts)
0 connections closed (including 0 drops)
0 connections updated cached RTT on close
0 connections updated cached RTT variance on close
0 connections updated cached ssthresh on close
0 embryonic connections dropped
226 segments updated rtt (of 228 attempts)
0 retransmit timeouts
0 connections dropped by rexmit timeout
0 persist timeouts
0 connections dropped by persist timeout
0 keepalive timeouts
0 keepalive probes sent
0 connections dropped by keepalive
0 correct ACK header predictions
88 correct data packet header predictions

310 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show traffic

show traffic

Purpose
Displays recent traffic summary statistics.

Format
statistics show summary-stats

Mode
Privileged

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 311

show udp statistics

show udp statistics

Purpose
Displays User Datagram Protocol (UDP) statistics.

Format
show udp statistics

Mode
Privileged

Parameters
None.

Restrictions
None.

Example
To display UDP statistics:

xp# show udp statistics

udp:
0 datagrams received
0 datagrams with incomplete header
0 datagrams with bad data length field
0 datagrams with bad checksum
0 datagrams dropped due to no socket
0 broadcast/multicast datagrams dropped due to no socket
0 datagrams dropped due to full socket buffers
0 datagrams not for hashed pcb
0 delivered
0 datagrams output

312 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 47

stp Command

The show stp command displays Shielded Twisted Pair (STP) bridging information.

Format
show stp [bridge]

Mode
Privileged

Description
The show stp command, when followed by the bridge keyword, displays STP bridging
information for the X-Pedition.

Parameters
bridge Displays information for STP bridging.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 313

314 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Command Summary

Chapter 48

system Commands

The system commands allow the user to display and change system parameters.

Command Summary
Table 35 lists the system commands. The sections following the table describe the
command syntax.

Table 35. system commands

clock set hh:mm:ss d m y

disconnect session-id
erase <filename> primary-cm| backup-cm
show bootlog
show bootprom
show buffers
show clock
show contact
show diagbus
show environment
show flash
show location
show login-banner
show logging

Enterasys X-Pedition Common Command Line Interface Reference Manual 315

Command Summary

Table 35. system commands (Continued)

show logging buffer

show memory
show name
show poweron-selftest-mode
show processes
show running-config
show scratchpad
show sessions
show startup-config
show terminal
show timezone
show uptime
show users
show version
system hostswap out| in <channel number>
system image choose <filename> primary-cm| backup-cm
system promimage-upgrade <hostname-or-IPaddr> <filename>

316 Enterasys X-Pedition Common Command Line Interface Reference Manual

 clock set

clock set

Purpose
Sets the system time and date.

Format
clock set <hh:mm:ss d m y>

Mode
Privileged

Description
The clock set command sets the system time and date for the X-Pedition. The X-Pedition
keeps the time in a battery-backed real-time clock. To display the time and date, enter the
show clock command.

Parameters
hh: A number from 0 - 23 for the hour, in military time. (Example: 06: [6 a.m.];
18: [6 p.m.]; the number 00 means midnight)
mm: A number from 0 - 59 for the minutes.
ss A number from 0 - 59 for the second.
day A number from 1 – 31 for the day.
month Name of the month. You must spell out the month name. (Example: March).
year Four-digit number for the year. (Example: 2000)

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 317

disconnect

disconnect

Purpose
Disconnects a specified Telnet session.

Format
disconnect <session-id>

Mode
Privileged

Description
The disconnect command kills the Telnet session specified by the session ID. Use the
show users command to display the list of current Telnet users and session IDs.

Parameters
<session-id>
The Telnet connection slot number, which can be 0, 1, 2, or 3. The show users
command displays the session ID number in the first column. You can only specify
one session ID per disconnect command.

Restrictions
None.

Example
To show the active Telnet sessions.

xp# show users

Current Terminal User List:
# Login ID Mode From Login Timestamp
- -------- ---- ---- ---------------
enabled console Thu Feb 25 13:07:411999
0 enabled 10.9.0.1 Thu Feb 25 13:07:591999
2 login-prompt 10.9.0.1
3 login-prompt 10.9.0.1

318 Enterasys X-Pedition Common Command Line Interface Reference Manual

 disconnect

Then, to disconnect Telnet session 2:

xp# disconnect 2
Telnet session 2 (from 10.9.0.1) killed

The example above shows the contents of the boot log file, which contains all the system
messages generated during bootup.

Enterasys X-Pedition Common Command Line Interface Reference Manual 319

erase

erase

Purpose
Deletes a system software image file from the PCMCIA flash card.

Format
erase <filename> primary-cm| backup-cm

Mode
Privileged

Description
The erase command deletes a system software image file from the PCMCIA flash card on
the Control Module.

Parameters
<filename> The name of the system software image file you want to delete.
primary-cm This parameter deletes the image file from the primary control module.
backup-cm This parameter deletes the image file from the backup control module.

Restrictions
None.

320 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show bootlog

show bootlog

Purpose
Displays bootlog information.

Format
show bootlog

Mode
Privileged

Description
The show bootlog command displays the contents of the boot log file, which contains
all the system messages generated during bootup.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 321

show bootprom

show bootprom

Purpose
Displays bootprom information.

Format
show bootprom

Mode
Privileged

Description
The show bootprom command displays boot PROM parameters for TFTP
downloading of the system image. This information is useful only if you have
configured the system to download the system image via TFTP.

Parameters
None.

Restrictions
None.

322 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show buffers

show buffers

Purpose
Displays usage information.

Format
show buffers

Mode
Privileged

Description
The show buffers command displays usage information about various resources on the
X-Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 323

show clock

show clock

Purpose
Displays system time and date.

Format
show clock

Mode
Privileged

Description
The show clock command displays the system time and date determined with the clock
set command.

Parameters
None.

Restrictions
None.

324 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show contact

show contact

Purpose
Displays contact information.

Format
show contact

Mode
Privileged

Description
The show contact command displays administrator contact information.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 325

show diagbus

show diagbus

Purpose
Displays system hardware information.

Format
show diagbus

Mode
Privileged

Description
The show diagbus command displays system hardware information.

Parameters
None.

Restrictions
None.

326 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show environment

show environment

Purpose
Displays system environment information.

Format
show environment

Mode
Privileged

Description
The show environment command displays system environment information, such as
temperature and power supply status.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 327

show flash

show flash

Purpose
Lists the system software image files on the PCMCIA flash card.

Format
show flash backup-cm| primary-cm

Mode
Privileged

Description
The show flash command lists the system software image files contained on the PCMCIA
flash card on the Control Module.

Parameters
backup-cm This parameter lists the image files on the backup control module.
primary-cm This parameter lists the image files on the primary control module.

Restrictions
None.

328 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show location

show location

Purpose
Displays location of the X-Pedition.

Format
show location

Mode
Privileged

Description
The show location command displays the location of the X-Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 329

show login-banner

show login-banner

Purpose
Displays login banner for the X-Pedition.

Format
show login-banner

Mode
Privileged

Description
The show login-banner command displays the X-Pedition’s login banner.

Parameters
None.

Restrictions
None.

330 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show logging

show logging

Purpose
Displays SYSLOG information.

Format
show logging

Mode
Privileged

Description
The show logging command displays the IP address of the SYSLOG server and the
level of messages the X-Pedition sends to the server.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 331

show logging buffer

show logging buffer

Purpose
Displays SYSLOG buffer information.

Format
show logging buffer

Mode
Privileged

Description
The show logging buffer command shows how many SYSLOG messages the X-
Pedition’s SYSLOG message buffer can hold.

Parameters
None.

Restrictions
None.

332 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show memory

show memory

Purpose
Displays memory resource information.

Format
show memory

Mode
Privileged

Description
The show logging buffer command displays information about memory resources on
the X-Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 333

show name

show name

Purpose
Displays the X-Pedition’s name.

Format
show name

Mode
Privileged

Description
The show name command displays the name of the X-Pedition.

Parameters
None.

Restrictions
None.

334 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show poweron-selftest-mode

show poweron-selftest-mode

Purpose
Displays Power-On Self Test (POST) information.

Format
show poweron-selftest-mode

Mode
Privileged

Description
The show poweron-selftest-mode command displays the type of Power-On Self Test
(POST) that should be performed, if any.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 335

show processes

show processes

Purpose
Displays information on the CPU.

Format
show processes

Mode
Privileged

Description
The show processes command displays the percentage of the CPU that is currently
being used.

Parameters
None.

Restrictions
None.

336 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show running-config

show running-config

Purpose
Displays system’s active configuration.

Format
show running-config

Mode
Privileged

Description
The show running-config command displays the active configuration of the system.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 337

show scratchpad

show scratchpad

Purpose
Displays configuration information.

Format
show scratchpad

Mode
Privileged

Description
The show scratchpad command displays the configuration changes in the scratchpad.
These changes have not yet been activated.

Parameters
None.

Restrictions
None.

338 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show sessions

show sessions

Purpose
Displays Telnet session information.

Format
show sessions

Mode
Privileged

Description
The show sessions command lists the last five Telnet connections to the X-Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 339

show startup-config

show startup-config

Purpose
Displays contents of startup configuration file.

Format
show startup-config

Mode
Privileged

Description
The show startup-config command displays the contents of the startup configuration
file.

Parameters
None.

Restrictions
None.

340 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show terminal

show terminal

Purpose
Displays terminal information.

Format
show terminal

Mode
Privileged

Description
The show terminal command displays default terminal settings (number of rows,
number of columns, and baud rate).

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 341

show timezone

show timezone

Purpose
Displays the time zone.

Format
show timezone

Mode
Privileged

Description
The show timezone command shows the time zone offset from UCT in minutes.

Parameters
None.

Restrictions
None.

342 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show uptime

show uptime

Purpose
Displays up-time information.

Format
show uptime

Mode
Privileged

Description
The show uptime command shows how much time has elapsed since the most recent
reboot.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 343

show users

show users

Purpose
Shows current Telnet connections to the X-Pedition.

Format
show users

Mode
Privileged

Description
The show users command shows all current Telnet connections to the X-Pedition.

Parameters
None.

Restrictions
None.

344 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show version

show version

Purpose
Shows software version running on X-Pedition.

Format
show version

Mode
Privileged

Description
The show version command displays the software version currently running on the X-
Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 345

system hotswap

system hotswap

Purpose
Activates or deactivates a line card.

Format
system hotswap out| in <channel number>

Mode
Privileged

Description
The system hotswap out command deactivates a line card in a specified slot on the X-
Pedition, causing it to go offline. The command performs the same function as if you had
pressed the Hot Swap button on the line card.
The system hotswap in command causes a line card that was deactivated with the system
hotswap out command to go online again. The command performs the same function as if
you had removed the card from its slot and inserted it again.
See the Enterasys X-Pedition User Reference for more information on hot swapping line
cards.

Parameters
out Causes the line card in the specified slot to be deactivated.
in Causes an inactive line card in the specified slot to be reactivated.
Note: The system hotswap in command works only on a line card that was
deactivated with the system hotswap out command.
<channel number>
Specifies the slot where the line card resides. Enter any number between 0-15.

Restrictions
None.

346 Enterasys X-Pedition Common Command Line Interface Reference Manual

 system hotswap

Example
To deactivate the line card in slot 7 on the X-Pedition:

xp# system hotswap out slot 7

Enterasys X-Pedition Common Command Line Interface Reference Manual 347

system image-choose

system image-choose

Purpose
Selects a system software image file.

Format
system image-choose <filename> primary-cm| backup-cm

Mode
Privileged

Description
The system image-choose command specifies the system software image file on the
PCMCIA flash card that you would like the X-Pedition to use the next time you reboot the
system.

Parameters
<filename> The name of the system software image file. If you would like to specify no
image chosen for the next reboot, enter none.
primary-cm This parameter specifies that the image file is chosen for the primary control
module.
backup-cm This parameter specifies that the image file is chosen for the backup control
module.

Restrictions
None.

348 Enterasys X-Pedition Common Command Line Interface Reference Manual

 system promimage-upgrade

system promimage-upgrade

Purpose
Upgrades the boot PROM software on the Control Module.

Format
system promimage-upgrade <hostname-or-IPaddr> <filename>

Mode
Privileged

Description
The system promimage-upgrade command copies and installs a boot PROM software
image from a TFTP server onto the internal memory on the Control Module. The boot
PROM software image is loaded when you power on the X-Pedition and in turn loads the
system software image file.

Parameters
<hostname-or-IPaddr>
The host name or IP address of the TFTP server or a TFTP URL.
<filename>
The name of the boot PROM software image file.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 349

system promimage-upgrade

Example
The command in the following example downloads a boot PROM image file from the
TFTP server 10.50.89.88.

xp# system promimage-upgrade tftp://10.50.89.88 qa/prom-upgrade

Downloading image ‘qa/prom-upgrade’ from host ‘10.50.89.88’
tftp complete
checksum valid. Ready to program.
flash found at 0xbfc00000
erasing...
programming...
verifying...
programming successful.
Programming complete.

350 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 49

tacacs-plus Command

The show tacacs command displays information about TACACS Plus configuration on
the X-Pedition.

Format
show tacacs

Mode
Enable

Description
The show tacacs command displays statistics and configuration parameters related to
TACACS Plus configuration on the X-Pedition. The statistics displayed include:
accepts Number of times each server responded and validated the user successfully.
rejects Number of times each server responded and denied the user access, either
because the user wasn’t known, or the wrong password was supplied.
timeouts Number of times each server did not respond.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 351

352 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Chapter 50

tech-support Command

The show tech-support command displays general information about the X-Pedition for
use when reporting a problem.This command is available in Common CLI syntax only.

Format
show tech-support

Mode
Privileged

Description
The show tech-support command simultaneously lists the information found in each of
the following system commands:
• show buffers
• show hardware
• show interfaces
• show processes
• show running-config
• show version
This information is helpful when reporting a problem to Enterasys Technical Support.

Parameters
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 353

Restrictions
None.

354 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 51

telnet Command

The telnet command opens a Telnet session to the specified host.

Format
telnet <hostname-or-IPaddr> <socket-number>

Mode
User or Privileged

Description
The telnet command allows you to open a Telnet session to the specified host.

Parameters
<hostname-or-IPaddr>
The host name or IP address of the remote computer that you would like to access.
<socket-number>
The TCP port through which the Telnet session will be opened. If this parameter is not
specified, the Telnet port (socket number 23) is assumed. This parameter can be used
to test other ports; for example, socket number 21 is the port for FTP.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 355

Example
To open a Telnet session on the host “ssr4”:

xp# telnet ssr4

356 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 52

terminal cli native

Command

The terminal cli native command switches the CLI environment over to the Native CLI
engine.

Format
terminal cli native

Mode
Privileged

Description
The terminal cli native command switches the CLI environment over to the Native CLI
engine. When executed in Privileged mode, the CLI of the system will become configured
to use the Native CLI commands and attributes.
Note: All current and future login sessions will use the Native CLI, until the user
switches back to the Common CLI engine.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 357

358 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Chapter 53

traceroute Command

The traceroute command traces the path a packet takes to reach a remote host.

Format
traceroute <host> [max-ttl <num>] [probes <num>] [size <num>] [source <host>]
[tos <num>] [wait-time <secs>] [verbose] [noroute]

Mode
User

Description
The traceroute command traces the route taken by a packet to reach a remote IP host. The
traceroute command examines the route taken by a packet traveling from a source to a
destination. By default, the source of the packet is the X-Pedition. However, one can
specify a different source and track the route between it and a destination. The route is
calculated by initially sending a probe (packet) from the source to the destination with a
TTL of 1. Each intermediate router that is not able to reach the final destination directly
will send back an ICMP Time Exceeded message. Subsequent probes from the source will
increase the TTL value by 1. As each Time Exceeded message is received, the program
keeps track of the address of each intermediate gateway. The probing stops when the
packet reaches the destination or the TTL exceeds the max-ttl value.

Parameters
<host>
Hostname or IP address of the destination
max-ttl <num>
Maximum number of gateways (“hops”) to trace

Enterasys X-Pedition Common Command Line Interface Reference Manual 359

 probes <num>
Number of probes to send
size <num>
Packet size of each probe
source <host>
Hostname or IP address of the source
tos <num>
Type of Service value in the probe packet
wait-time <secs>
Maximum time to wait for a response
verbose
Displays results in verbose mode
noroute
Ignores the routing table and sends a probe to a host on a directly attached network. If
the destination is not on the local network, an error is returned.

Restrictions
None.

Example
To display the route from the X-Pedition to the host othello in verbose mode:

xp# traceroute othello verbose

360 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Chapter 54

vlan Command

The show vlan command displays a list of all VLANs active on the X-Pedition.

Format
show vlan

Mode
Privileged

Description
The show vlan command lists all the VLANs that have been configured on the X-
Pedition.

Parameters
None.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 361

362 Enterasys X-Pedition Common Command Line Interface Reference Manual
 Command Summary

Chapter 55

web-cache Commands

The web-cache commands allow you to transparently redirect HTTP requests to a group
of local cache servers. This feature can provide faster user responses and reduce demands
for WAN bandwidth.

Command Summary
Table 36 lists the web-cache commands. The sections following the table describe the
command syntax.

Table 36. web-cache commands

clear ip web-cache all| cache-name <cache-name>

show ip web-cache [all] [cache-name <cache-name>| all] [servers cache <cache-
name>| all]

Enterasys X-Pedition Common Command Line Interface Reference Manual 363

clear ip web-cache

clear ip web-cache

Purpose
Clears statistics for the specified caching policy.

Format
clear ip web-cache all| cache-name <cache-name>

Mode
Privileged

Description
The clear web-cache command allows the user to clear statistics for all caching policies
or for specified policies.

Parameters
all
Clears statistics for all caching policies.
cache-name <cache-name>
Clears statistics for the specified caching policy.

Restrictions
None.

Examples
To clear statistics for the caching policy ‘websrv1’:

xp# clear ip web-cache cache-name websrv1

364 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip web-cache

show ip web-cache

Purpose
Displays information about caching policies.

Format
show ip web-cache [all] [cache-name <cache-name>| all] [servers cache <cache-
name>| all]

Mode
Privileged

Description
The show web-cache command allows the user to display web caching information for
specific caching policies or server lists.

Parameters
all
Displays all web cache information for all caching policies and all server lists.
cache-name <cache-name>| all
Displays web cache information for the specified caching policy. all displays all
caching policies.
servers cache <cache-name>| all
Displays information for the servers configured for the specified caching policy. all
displays all configured cache servers.

Restrictions
None.

Enterasys X-Pedition Common Command Line Interface Reference Manual 365

show ip web-cache

Examples
To display web cache information for a specific caching policy:

xp# show ip web-cache cache-name cache1

Cache Name : cache1 1
Applied Interfaces : ip1 2
Bypass list : none 3
HTTP Port : 80 4

5 6 7 8 9 10 11
ACL Source IP/Mask Dest. IP/Mask SrcPort DstPort TOS Port
--- -------------- ------------- --------- --------- --- ----
deny207 172.89.1.1/32 207.135.0.0/16 any http 0 IP

12 13 14
Server Max con IP address
---- -- ------- ----------
s1 2000 176.89.10.50 - 176.89.10.60

Access Users 15
------ -----
Permit All Users
Deny profile deny207

Legend:
1. The name of the cache policy.
2. The outbound interface where the cache policy was applied, typically an interface that
connects to the Internet.
3. Destination sites for which HTTP requests are not redirected to cache servers and are
sent direct.
4. The HTTP port used by a proxy server.
5. The names of the profiles (created with an acl statement) associated with this cache
policy.
6. The source address and filtering mask.
7. The destination address and filtering mask.
8. The source port.
9. The destination port.
10. The TOS value in the packet.
11. The protocol.
12. The server list name.

366 Enterasys X-Pedition Common Command Line Interface Reference Manual

 show ip web-cache

13. The maximum number of connections that can be handled by each server in the server
list.
14. The list or range of IP addresses of the servers in the server list.
15. The hosts (users) whose HTTP requests are redirected to the cache servers and the
hosts whose HTTP requests are not redirected to the cache servers. If no permit
command is specified, all HTTP requests are redirected to the cache servers.
To display information for all configured web cache servers:

xp# show ip web-cache servers cache cache1

Cache name : cache1 1

2 3 4 5 6
Block IP address Max Conn Used Cnt Status
----- ---------- -------- -------- ------
s1 176.89.10.50 2000 0 Down
s1 176.89.10.51 2000 0 Down
s1 176.89.10.52 2000 0 Down
s1 176.89.10.53 2000 0 Down
s1 176.89.10.54 2000 0 Down
s1 176.89.10.55 2000 0 Down
s1 176.89.10.56 2000 0 Down
s1 176.89.10.57 2000 0 Down
s1 176.89.10.58 2000 0 Down
s1 176.89.10.59 2000 0 Down
s1 176.89.10.60 2000 0 Down

Legend:
1. The name of the cache policy.
2. The server list name.
3. The IP address of a server in the server list.
4. The maximum number of connections that can be handled by the server.
5. The number of connections currently being handled by the server.
6. The current status of the server.

Enterasys X-Pedition Common Command Line Interface Reference Manual 367

show ip web-cache

368 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Appendix A

CLI Conversion
Matrix

The following matrix allows the user to convert X-Pedition Native CLI commands to
Common CLI commands.

Expedition v8.0 CLI Common CLI Mode

ACL (ACCESS LIST) COMMANDS

acl clearcounters aclname all | interface | clear access-list counters <num> | <name> PRIV
service | port

acl show [aclname <string> | all] | show access-lists [<num> | <string> | PRIV
[interface <string> | all-ip] | [service] | [port {interface <string> | all-ip} | service | {port
<port-list> | all-ports] | [all] <port-list> \ all-ports}]

AGING COMMANDS

aging l2 show status show mac-address-table aging-time USER

aging l3 show status show mls aging USER

ARP COMMANDS

arp add <host> mac-addr <MAC-addr> arp add <host> mac-addr <MAC-addr> PRIV
exit-port <port> keep-time <seconds> exit-port <port> keep-time <seconds>

arp clear <host> | all [interface <string> | arp clear <host> mac-addr <MAC-addr> PRIV
all] [port <port>] exit-port <port> keep-time <seconds>

arp show <IPaddr> | all [undecoded] arp show <IPaddr> | all [undecoded] PRIV
[unresolved] [interface <string> | all] [port [unresolved] [interface <string> | all] [port
<port>] <port>]

statistics show arp show arp statistics PRIV

ATM COMMAND

Enterasys X-Pedition Common Command Line Interface Reference Manual 369

 Expedition v8.0 CLI Common CLI Mode
atm show [vpl port <port-list>] [vcl port show atm [vpl port <port-list>] [vcl port PRIV
<port-list>] [service] [port-settings <port- <port-list>] [service] [port-settings <port-
list> | all-ports] list> | all-ports]

BGP COMMANDS

bgp show routes <IPaddr-mask> | default | show ip bgp [<IPaddr> <IPmask>] [to- PRIV
all [to-terminal | to-file] file]

bgp show cidr-only <IPaddr-mask> | show ip bgp cidr-only [<IPaddr> PRIV

default | all [to-terminal | to-file] <IPmask>] [to-file]

bgp show community community-id show ip bgp community {<community-id> | PRIV

<number> autonomous-system <number> | <ASnum> | no-export | no-advertise | no-
well-known-community [no-export | no- export subconfed | reserved-community
advertise | no-export subconfed] | reserved- <hexnum>} [to-file]
community <number>] [to-terminal | to-
file]

bgp show peer-host <IPaddr> received- show ip bgp neighbor <IPaddr> routes | PRIV
routes | all-received-routes | advertised- received-routes | advertised-routes [to-file]
routes [to-terminal | to-file]

bgp show peer-as <number> [to-terminal | show ip bgp peer-as <number> [to-file] PRIV
to-file]

bgp show peer-group-type external | internal show ip bgp peer-group external | internal | PRIV
| igp | routing [to-terminal | to-file] igp | routing [to-file]

bgp show regexp <regexp> show ip bgp regexp <regexp> PRIV

bgp show summary [to-terminal | to-file] show ip bgp summary [to-file] PRIV

bgp show sync-tree show ip bgp sync-tree PRIV

CLI COMMANDS

cli show history show history USER

cli show terminal show terminal USER

cli set command completion on | off terminal command-completion on | off USER

cli set history size <num> | default | terminal history size <buffer-size> USER
maxsize

cli set terminal rows <num> columns terminal length <screen-length> USER
<num> terminal width <line-length>

cli terminal monitor on | off terminal monitor PRIV

COPY COMMANDS

370 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Expedition v8.0 CLI Common CLI Mode
copy [active | scratchpad | tftp-server | rcp- copy [tftp | rcp | active | scratchpad | startup | PRIV
server | startup | <filename> | <url>] to <filename>] [tftp | rcp | active | scratchpad |
[backup-CM | active | scratchpad | tftp- startup | <filename>]
server | rcp-server | startup | <filename> |
<url>]

system image add <IPaddr-or-hostname> copy tftp flash PRIV

<filename>

DHCP COMMANDS

dhcp flush clear ip dhcp PRIV

dhcp show binding [active | expired | static] show ip dhcp binding [active | expired | PRIV
static]

dhcp show num-clients show ip dhcp num-clients PRIV

DVMRP COMMANDS

dvmrp show interface [<IPaddr>] show ip dvmrp interface <IPaddr> PRIV

dvmrp show routes host <IPaddr> | show ip dvmrp route [<port-list> | PRIV
interface <IPaddr> | net <netaddr> | router <IPaddr>]
<IPaddr>

dvmrp show rules show ip dvmrp rules PRIV

ENABLE COMMAND

enable enable PRIV

EXIT COMMAND

exit exit PRIV

FDDI COMMANDS

fddi reset <port-list> clear fddi <port-list> PRIV

fddi show fddi-fdx-mode | fddi-mode | fddi- show fddi fddi-fdx-mode | fddi-mode | fddi- PRIV
status | mac-group | mac-restricted-token | status | mac-group | mac-restricted-token |
media-type | path-group | port-group | ring- media-type | path-group | port-group | ring-
purger | smt-config | smt-group | translation | purger | smt-config | smt-group | translation |
version <port-list> | all-ports version <port-list> | all-ports

FILE COMMANDS

file delete <file-name> delete <file-name> PRIV

file dir <device-name> dir <device-name> USER

file type <file-name> show file <file-name> PRIV

FILTERS COMMANDS

Enterasys X-Pedition Common Command Line Interface Reference Manual 371

 Expedition v8.0 CLI Common CLI Mode
filters show address-filter [all-source | all- show filters address-filter [all-source | all- PRIV
destination | all-flow] [source-mac destination | all-flow] [source-mac
<MACaddr> dest-mac <MACaddr>] [ports <MACaddr> dest-mac <MACaddr>] [ports
<port-list>] [vlan <VLANnum>] <port-list>] [vlan <VLANnum>]

filters show port-address-lock [ports <port- show filters [port-address-lock] [ports PRIV
list>] [vlan <VLANnum>] [source-mac <port-list>] [vlan <VLANnum>] [source-
<MACaddr>] mac <MACaddr>]

filters show secure port show filters [secure-port] PRIV

filters show static-entry [all-source | all- show filters [static-entry] [all-source | all- PRIV
destination | allow-flow] ports <port-list> destination | allow-flow] ports <port-list>
vlan <VLANnum> [source-mac vlan <VLANnum> [source-mac
<MACaddr> dest-mac <MACaddr>] <MACaddr> dest-mac <MACaddr>]

FRAME RELAY COMMANDS

frame-relay clear stats-counter [frame-drop- clear frame-relay [frame-drop-qdepth- PRIV

qdepth-counter] [max-frame-enqued- counter] [max-frame-enqued-counter]
counter] [frame-drop-red-counter] [rmon] [frame-drop-red-counter] [rmon] [<port-
ports <port-list> list>]

frame-relay show service <service-name> | show frame-relay service PRIV

all

frame-relay show stats port <port-name> show frame-relay stats PRIV

[last-error] [lmi] [mibII] [summary]

IGMP COMMANDS

igmp show interfaces [group <IPaddr> | show ip igmp interface <port-list> PRIV1
interface <name/IPaddr>]

igmp show memberships [group <IPaddr> | show ip igmp groups <IPaddr> PRIV
port <port-list>]

igmp show timers show ip igmp timers PRIV

igmp show vlans show ip igmp vlans PRIV

IP COMMANDS

ip clear reverse-flows ip clear reverse-flows PRIV

ip show hash-variant <num> | all show ip hash-variant PRIV

ip show helper-address show ip helper-address PRIV

ip show interfaces [<interface-name>] show ip interface PRIV

[brief]

ip show reverse-flows show ip reverse-flows PRIV

ip show routes [no-lookup] [show-arps] show ip route PRIV

[show-multicast] [verbose]

372 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Expedition v8.0 CLI Common CLI Mode
ip show routes show-protocol [bgp | direct | show ip route [bgp | connected | ospf | ospf- PRIV
ospf | ospf-ase | rip | static] ase | rip | static]

ip show routes show-summary show ip route summary PRIV

ip show connections [no-lookup] show tcp [dns-lookup] PRIV

show udp [dns-lookup]

IP-POLICY COMMANDS

ip-policy clear policy-name <name> | all clear route-map [policy-name <name> | all] PRIV

IP-REDUNDANCY COMMANDS

ip-redundancy clear vrrp-stats interface clear vrrp <VRid> interface <name> PRIV
<name> id <VRid>

ip-redundancy set vrrp <VRid> interface show vrrp <VRid> interface <name> PRIV
<name> [priority <num>] [adv-interval
<num>] [preempt-mode enabled | disabled |
owner-disabled] [auth-type none | text]
[auth-key <key>] [warmup-period <num>]

IP-ROUTER COMMANDS

ip-router find route <IPaddr> [ignore-state] ip find rib-route <IPaddr> [ignore-state] PRIV

ip-router show configuration-file active | show gated-config active | permanent PRIV

permanent

ip-router show rib [detail] show ip route [summary] PRIV

ip-router show route [ip-addr-mask | show ip route <IPaddr> [detail] PRIV

default] [detail]

ip-router show state [all] [memory] [timers] show ip route state PRIV
[to-file] [to-terminal] [task <string> | all |
gii | icmp | inet | interface | krt | route]

IPX COMMANDS

ipx find rip <address> ipx find rip <address> PRIV

ipx find sap <type> | all <SRVCname> | all ipx find sap <type> | all <SRVCname> | all PRIV
<network> | all <entrytype> <network> | all <entrytype>

ipx show buffers show ipx buffers PRIV

ipx show interfaces <interface> [brief] show ipx interface [<interface>] PRIV

ipx show rib <destination> show ipx rib destination USER

ipx show servers hops | net | name | type show ipx servers {sorted [hops | net | name | USER
type]} | unsorted

ipx show tables routing | rip | sap | summary show ipx route USER

Enterasys X-Pedition Common Command Line Interface Reference Manual 373

 Expedition v8.0 CLI Common CLI Mode
L2 (MAC ADDRESS TABLE) COMMANDS

l2-tables show all-flows {vlan <VLANnum> show mac-address-table all-flows [vlan USER
[source-mac <MACaddr>]} [undecoded] <VLANnum>] [source-mac <MACaddr>] PRIV
[undecoded]

l2-tables show all-macs {verbose show mac-address-table all-macs [vlan USER

[undecoded]} [vlan <VLANnum>] [source] <VLANnum>] [source-mac <MACaddr>] PRIV
[destination] [multicast] [source] [destination] [multicast]

l2-tables show bridge-management show mac-address-table bridge- USER

management PRIV

l2-tables show igmp-mcast-registrations show mac-address-table igmp-mcast- USER

[vlan <VLANnum>] registration [vlan <VLANnum>] PRIV

l2-tables show mac <MACaddr> vlan show mac-address-table address USER

<VLANnum> <MACaddr> vlan <VLANnum> PRIV

l2-tables show mac-table-stats show mac-address-table mac-table-stats USER

PRIV

l2-tables show port-mac <port-list> | all- show mac-address-table port-macs <port- USER
ports {[vlan <VLANnum>] [source] list> | all-ports {verbose [vlan PRIV
[destination] [multicast] [undecoded] [no- <VLANnum>] [source] [destination]
stats] verbose} [multicast] [undecoded] [no-stats]}

l2-tables show vlan-igmp-status vlan show mac-address-table vlan-igmp-status PRIV

<VLANnum> vlan <VLANnum>

LFAP COMMANDS

lfap show all show lfap PRIV

lfap show configuration show lfap configuration PRIV

lfap show servers show lfap servers PRIV

lfap show statistics show lfap statistics PRIV

lfap show status show lfap status PRIV

LOAD-BALANCE COMMANDS

load-balance set server-status server-ip load-balance set server-status PRIV

<IPaddr> server-port <port> group-name
<string> status up | down

load-balance show acv-options [group- show load-balance acv-options PRIV

name <string>] [destination-host-ip
<IPaddr>] [destination-host-port <port>]

load-balance show hash-stats show load-balance hash-stats PRIV

load-balance show source-mappings client- show load-balance source-mappings PRIV

ip <IPaddr> virtual-ip <IPaddr> virtual-
port <port> destination-host-ip <IPaddr>

374 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Expedition v8.0 CLI Common CLI Mode
load-balance show statistics group-name show load-balance statistics PRIV
<string> virtual-ip <IPaddr> virtual-port
<port>

load-balance show virtual-hosts group- show load-balance virtual-hosts PRIV

name <string> virtual-ip <IPaddr> virtual-
port <port>

LOGOUT COMMAND

logout logout ALL

MTRACE COMMAND

mtrace <source> mtrace <source> PRIV

MULTICAST COMMANDS

multicast show interface [<IPaddr> | show ip multicast interface PRIV

<hostname>]

multicast show mroutes [child <IPaddr>] show mroute [child <IPaddr>] [group PRIV
[group <IPaddr>] [parent <IPaddr>] <IPaddr>] [parent <IPaddr>]

NAT COMMANDS

nat clear-err-stats out-of-globals | port-mode clear ip nat out-of-globals | port-mode PRIV

nat flush-dynamic-binding all | pool- clear ip nat translation {pool-specified PRIV

specified [local-acl-pool <localACL>] [local-acl-pool <localACL>] [global-pool
[global-pool <IPaddr/range>] <IPaddr/range>]}

nat show [translations] [timeouts] show ip nat [statistics | timeouts | PRIV

[statistics] translations]

NTP COMMANDS

ntp synchronize server <host> ntp synchronize server <host> PRIV

ntp show all show ntp [associated | status] PRIV

OSPF COMMANDS

ospf show <option-list> show ip ospf PRIV

show ip ospf interface

PING COMMAND

ping <hostname-or-IPaddr> packets ping <hostname-or-IPaddr> packets PRIV

<num> size <num> wait <num> [flood] <num> size <num> wait <num> [flood]
[dontroute] [dontroute]

PORT COMMANDS

port show bmon show bmon PRIV

port show bridging-status <port-list> | all- show bridging PRIV

ports

Enterasys X-Pedition Common Command Line Interface Reference Manual 375

 Expedition v8.0 CLI Common CLI Mode
port show description <port-list> | all-ports show interface <port-list> PRIV

port show 8021p <port-list> | all-ports show port 8021 PRIV

port show autonegotiation <port-list> | all- show port autonegotiation <port-list> | all- PRIV
ports ports

port show autonegotiation-capabilities show port autonegotiation-capabilities PRIV

<port-list> | all-ports <port-list> | all-ports

port show MAU <port-list> | all-ports show port MAU <port-list> PRIV

port show MAU-statistics <port-list> | all- show port MAU-statistics <port-list> PRIV
ports

port show mirroring-status <port-list> | all- show port-mirroring [<port-list> | acls] PRIV
ports | all-acls

port show port-status <port-list> | all-ports show port status <port-list> PRIV

port show stp-info <port-list> | all-ports show stp interface <port-list> PRIV

port show pvst-info <port-list> | all-ports show pvst <name> interface <port-list> PRIV

port show vlan-info <port-list> | all-ports show vlan interface <port-list> PRIV

PPP COMMANDS

ppp clear stats-counter [frame-drop-qdepth- clear ppp stats-counter ports <port-list> PRIV
counter] [max-frame-enqued-counter] {[frame-drop-qdepth-counter] [max-frame-
[frame-drop-red-counter] [rmon] port enqued-counter] [frame-drop-red-counter]
<port-list> [rmon]}

ppp restart lcp-ncp ports <port-list> ppp restart lcp-ncp ports <port-list> PRIV

ppp show mlp <port-list> | all-ports show ppp mlp <port-list> | all-ports PRIV

ppp show service <service-name> | all show ppp service <service-name> | all PRIV

ppp show stats port <port> [bridge-ncp] show ppp stats port <port> [bridge-ncp] PRIV
[ip-ncp] [link-status] [summary] [ip-ncp] [link-status] [summary]

PVST COMMAND (STP)

pvst show bridging-info spanning-tree show pvst <VLANnum> PRIV

<VLANnum>

QOS COMMANDS

qos show ip show qos ip PRIV

qos show ipx show qos ipx PRIV

qos show l2 all-destination all-flow ports show qos l2 all-destination all-flow ports PRIV
<port-list> vlan <VLANnum> source-mac <port-list> vlan <VLANnum> source-mac
<MACaddr> dest-mac <MACaddr> <MACaddr> dest-mac <MACaddr>

qos show precedence ip | ipx show qos precedence ip | ipx PRIV

376 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Expedition v8.0 CLI Common CLI Mode
qos show priority-map <string> | all show qos priority-map <string> | all PRIV

qos show wred [input port <port-list> | all- show qos wred [input port <port-list> | all- PRIV
ports] [port <port-list> | all-ports] ports] [port <port-list> | all-ports]

qos show wfq port <port-list> | all-ports show qos wfq <port-list> | all-ports PRIV

RADIUS COMMAND

radius show stats | all show radius PRIV

RARPD COMMAND

rarpd show interface | mappings show rarpd interface | mappings PRIV

RATE-LIMIT COMMAND

rate-limit show [all] | [policy-type flow- show rate-limit [all] | [policy-type flow- PRIV
policies | aggregate-policies | portlevel- policies | aggregate-policies | portlevel-
policies | all] | [policy-name <name>] | policies | all] | [policy-name <name>] |
[interface <interface>] | [port-level port [interface <interface>] | [port-level port
<port-list> | all-port] | [port-level policy- <port-list> | all-port] | [port-level policy-
name <name>] | [rate-limiting-mode] name <name>] | [rate-limiting-mode]

RDISC (IRDP) COMMAND

rdisc show show ip irdp PRIV

REBOOT COMMAND

reboot reload PRIV

RIP COMMANDS

rip trace [packets | request | response | local- rip trace [packets | request | response | local- PRIV
options] [detail] [send | receive] options] [detail] [send | receive]

rip show <option-list> show rip <option-list> PRIV

RMON COMMANDS

rmon clear cli-filter clear rmon cli filter PRIV

clear rmon statistics

rmon apply cli-filters <filter-id> rmon apply cli-filters <filter-id> PRIV

rmon show <option-list> show rmon [alarms | capture | events | filter | PRIV
history | matrix | statistics | task | topn]

SFS COMMANDS

sfs show cdp-hello port-status <port-list> | show sfs cdp-hello port-status <port-list> | PRIV
all-ports all-ports

sfs show cdp-hello transmit-frequency show sfs cdp-hello transmit-frequency PRIV

SMARTTRUNK COMMANDS

Enterasys X-Pedition Common Command Line Interface Reference Manual 377

 Expedition v8.0 CLI Common CLI Mode
smarttrunk clear load-distribution clear smarttrunk load-distribution PRIV
<SmartTRUNK> <SmartTRUNK>

smarttrunk show <option> show smarttrunk [distribution | protocol- PRIV

state | connections] <numlist>

SNMP COMMANDS

snmp show access | all | chassis-id | show snmp PRIV

community | statistics | trap

SONET COMMANDS

sonet show aps <SONETports> sonet show aps <SONETports> PRIV

sonet show loopback <SONETports> sonet show loopback <SONETports> PRIV

sonet show medium <SONETports> sonet show medium <SONETports> PRIV

sonet show pathtrace <SONETports> sonet show pathtrace <SONETports> PRIV

STATISTICS COMMANDS

statistics clear [port-errors | port-packets | clear interface [<port-list>] [errors | packets PRIV
port-stats] <port-list> | statistics]

statistics clear ip clear ip statistics PRIV

statistics clear ipx clear ipx statistics PRIV

statistics show icmp show ip icmp statistics PRIV

statistics show multicast show ip multicast PRIV

statistics show ip-routing show ip traffic PRIV

statistics show ipx-routing show ipx traffic PRIV

statistics show port-errors <port-list> | all- show port errors [<port-list>] PRIV
ports

statistics show port-packets <port-list> | show port packets [<port-list>] PRIV

all-ports

statistics show port-stats <port-list> | all- show port stats [<port-list>] PRIV
ports

statistics show top show processes cpu PRIV

statistics show rarp <ifname> | all show rarp [<ifname>] PRIV

statistics show tcp show tcp statistics PRIV

statistics show summary-stats show traffic PRIV

statistics show udp show udp statistics PRIV

STP COMMAND

378 Enterasys X-Pedition Common Command Line Interface Reference Manual

 Expedition v8.0 CLI Common CLI Mode
stp show bridging-info show stp [bridge] PRIV

SYSTEM COMMANDS

system set date year <num> month <num> clock set <hh:mm:ss> <day> <month> PRIV
day <num> hour <num> min <num> <year>
second <num>

system kill telnet-session <session-id> disconnect <session-id> PRIV

system image delete <filename> [primary- erase <filename> [primary-cm | backup- PRIV
cm | backup-cm] cm]

system show bootlog show bootlog PRIV

system show bootprom show bootprom PRIV

system show capacity show buffers PRIV

show memory

system show date show clock PRIV

system show contact show contact PRIV

system show hardware show diagbus PRIV

system show environmental-info show environment PRIV

system image list [primary-cm | backup-cm show flash PRIV

| all]

system show location show location PRIV

system show login-banner show login-banner PRIV

system show syslog show logging PRIV

system show buffer show logging buffer PRIV

system show name show name PRIV

system show poweron-selftest-mode show poweron-selftest-mode PRIV

system show cpu-utilization show processes PRIV

system show active-config show running-config PRIV

system show scratchpad show scratchpad PRIV

system show telnet-access show sessions PRIV

system show startup-config show startup-config PRIV

system show terminal show terminal PRIV

system show timezone show timezone PRIV

system show uptime show uptime PRIV

Enterasys X-Pedition Common Command Line Interface Reference Manual 379

 Expedition v8.0 CLI Common CLI Mode
system show users show users PRIV

system show version show version PRIV

system hotswap [out | in] channel system hotswap [out | in] channel PRIV
<number> <number>

system image choose <filename> [primary- system image choose <filename> [primary- PRIV
cm | backup-cm | none] cm | backup-cm]

system promimage upgrade system promimage upgrade PRIV

<hostname/IPaddr> <filename> <hostname/IPaddr> <filename>

TACACS COMMAND

tacacs show stats | all show tacacs PRIV

TACACS-PLUS COMMAND

tacacs-plus show stats | all show tacacs PRIV

TELNET COMMAND

telnet <hostname/IPaddr> [socket <socket- telnet USER

number>] PRIV

TRACE ROUTE COMMAND

traceroute <host> [max-ttl <num>] [probes traceroute <host> [max-ttl <num>] [probes USER
<num>] [size <num>] [source <host>] [tos <num>] [size <num>] [source <host>] [tos
<num>] [wait-time <secs>] [verbose] <num>] [wait-time <secs>] [verbose]
[noroute] [noroute]

VLAN COMMAND

vlan show show vlan PRIV

WEB-CACHE COMMANDS

web-cache clear [all | cache-name <cache- clear ip web-cache [all | cache-name PRIV
name>] <cache-name>]

web-cache show [all] [cache-name <cache- show ip web-cache [all] [cache-name PRIV
name> | all] [servers cache <cache-name> | <cache-name> | all] [servers cache <cache-
all] name> | all]

COMMON-MODE ONLY: TECH SUPPORT COMMAND

No Equivalent show tech-support PRIV

380 Enterasys X-Pedition Common Command Line Interface Reference Manual