No.

: :GAA31064AAA_STM
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 1/28
Berlin
DCSS5 Date: 2007-01-19
Service Tool Manual

(
DCSS 5-E
Service Tool User's Guide

Document Revision:

I
Date
2007-01-
19
II Author
Rudiger Lob
Comment
I Original Document

( (

.........
 No.: :GAA31064AAA_STM
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 2/28
Berlin
DCSS5 Date: 2007-01-19
Service Tool Manual

Copyright 2007, OTIS GmbH & Co. OHG Berlin

No part of tilis document may be oopied or reproduced in any fonn or by any means witllout ilie prior written consent of OTIS.

( (

( (

-
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AAI
Engineering Center Service Tool User's Guide Page: 42/28 Engineering Center Service Tool User's Guide Page.3/28
Berlin Berlin
DCSS5 Date: 2007.(J1-19 DCSS5 Date: 2001.(J1-19
Service Tool Manual Service Tool Manual

1 Display and Key Arrangement 5

7.3 ADAM (keys 343)
2 Connection to DeSS 5
This is a hidden feature. Pressing Shift & 7 this menu item becomes available.
( (' 3 Overview 6
ADAM stands for Advanced Diagnosis and Maintenance Tool. This is a PC Window based 3.1 Menu Overview 6
software tool, where the PC communicates with the DCSS via the serial link interface
3.2 Key-Function Overview 7
(Multidrop or CAN Bus). To connect the PC with the DCSS, the DCSS must reboot and has
to receive an initialization string from the PC, otherwise the DCSS boots with the normal 3.3 MODULE Operations 9
mode. 3.4 FUNCTION Operations 9
3.5 SET Operations 10
4 Monitor Function (keys: 31) 11
witch to Remote
l>YES NO<O> 4.1 Status Display (keys: 311) 11
4.2 Input Status Display (keys: 312) 13
4.2.1 3-Wire Standard 13
4.2.2 3-Wire Extended (DOB_FAST) 15
4.2.3 Multidrop 17
4.2.4 Relay (with Interface Box) 18
If the systems are connected following features are available:
4.3 Output Status Display (keys: 313) 18
4.4 Command Status Display (keys: 314) (hidden) 20
• On Board reprogramming of the DCSS software download
4.4.1 3-Wire Standard and Extended and Relay Interface: 20
• Load second native language for SVT messages 4.4.2 Multidrop Serial Link Interface: 20
• Upload and download installation parameter sets - archive and duplicate 5 Test Function (keys: 32) 21
installation sets
5.1 Event Menu Display (keys: 321) 21
• Perform long term monitoring of DCSS operation for error root cause analysis 5.1.1 Actual display (keys: 3211) 21
• Collect maintenance information 5.1.2 EvLog display (keys 3212) 23
5.1.3 History display (keys 3213) 23
• DCSS remote control
( ( 5.1.4 Del display (keys: 3219) 24
5.2 Maintenance (keys: 322) 24
5.3 Partnumber (keys: 323) 24
7.4 RESET (keys 344)
5.4 Interface Check (keys: 324) 24
This is a hidden feature. Pressing Shift & 7 this menu item becomes available. 5.5 System Configuration (keys:325) 26

Reset of the DCSS5-E without disconnected the power supply . To proceed it press 1. 6.0 Setup Function (keys: 33) 26
6.1 First Installation Profile 1 (key 331) 27
6.1.1 Configuration (keys 3311) 29
Are you sbure ? 6.1.2 Set Default (key 3319) 36
l>YES NO<O>
6.2 First Installation Profile 2 (key 332) 36
6.3 Parameter Setup ­ Field ­ (key 333) 37
6.4 Parameter Setup -Engineering ­ (key 334) 38
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AAI
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool Users Guide Page : 4/28 Engineering Center Service Tool Users Guide Page: 41/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual I
Service Tool Manual
,

7 Tools (keys: 34) 38

7.1 Single (keys 341) 40
press <GOON> to disable the reversal devices during continuous run:
7.2 Continuous (keys 342) 40
risab,ed RevDev
7.3 ADAM (keys 343)
( ( Start 3 >1
7.4 RESET (keys 344)

Switching to another menu does not interrupt the door movement. Parameter modification
stops immediately the continuous run.

(
\

I
 No.: :GAA31064AAA_SlM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 40/28 Engineering Center Service Tool User's Guide Page.5/28
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01·19
Service Tool Manual Service Tool Manual

1 Display and Key Arrangement

7.1 Single ( keys 341) The service tool front panel consists of a display with 2 lines, 16 characters per line, and 16
keys.
Executes single open or close commands. Select between operation with enabled or Some keys have a second function which is activated by pressing first the blue button and
disabled reversal devices. ( ( then the key.
The used key arrangement is as shown below:

!PI: Opn~1 Close=2 ..,

~top=3 RevCls=4 >

use <GOON>

use <GOON> to select 2.Profile commands

2: Opn=l Close=2
top=3 RevCls=4 >

use <GOON>

Following commands can be entered

Open' commands the door to open
Close: commands the door to close (Reversal device & stalled door protection
disabled)
Stop: commands the door to stop
RevCls: commands the door to close but Reversal devices are enabled (
Ndg: command the door to close in nudging mode

Switching to another menu does not interrupt the door movement. Parameter modification
stops immediately the single run.

2 Connection to DCSS
7.2 Continuous (keys 342)
Initiate continuous opening closing operation. Start and stop the continuous run and select When connected to any subsystem, the service tool conducts self-tests and then executes
between operation with enabled or disabled reversal devices . the set-up sequence. The following display will be made when normal communication is
!Continuous Run established with any subsystem.
starts continuous run (reversal devices are enabled)
I.. Start=3 >1
 No.: :GAA31064MA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 6128 Engineering Center Service Tool User's Guide Page : 39/28
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

3 Overview
3.1 Menu Overview ~ingle=l Cont.=2
enter <shift&7>
.~ngle=l
DAM=3
Cont.=21
RESET = 4

( (
I

( (

~
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 38/28 Engineering Center Service Tool User's Guide Page: 7/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

3.2 Key-Function Overview

6.4 Parameter Setup -Engineering ­ (key 334) The Service Tool front panel consists of a display with 2 lines, 16 characters per line, and
16 keys. Some keys have a second function (marked in blue color) which is activated by
This Menu provides access to the installation parameters, which at most of the job-sides { ' pressing SHIFT (first the unlabeled completely blue key which is located directly below
never have to be modified. Anyhow experience shows that there is no way to achieve 1000 ( the SET key) and than the key with the desired function.
coverage for all Job-sides, therefore we want to give you more flexibility. The Engineering­
parameter should be used only by experienced and trained users. For better overview the MODULE:
parameters are separated as following: Guides to the top level menu, the DCSS welcome message- interrupts automatic
installation.
rofl = 1 Profl = 2
FUNCTION:
ntrl== 3 Other = 4
use goon Guides to the second level menu. Inactive during automatic installation.

SET:
Returns from a Sub-menu to the Menu level of ownerShip. Inactive during automatic
Prof1: installation.
Parameters for the standard profile set 1
D/SPIN:
Prof2: Toggles between standard language and alternative language
Parameters for the alternative profile set 2
GO ON I GO BACK:
Cntrl: Navigate through for example a parameter scroll list pressing GOON for the next and the
Closed loop control parameters alternate function GOBACK for the previous list element.

Other: CLEAR:
Container for the rest Erase last entered value.

Relay: SHIFT & 7:

This menu is only available if the interface of DCSS5 is configured as a relay controller. On main menu and Inspection menu level only the following topics are displayed:
Parameter to setup the position controlled output signals.
( ( Main menu: Inspection menu:
Use "<GO ON>" I "<GO BACK>" to scroll through the available setup parameter.
Use the number keys to enter a new value and confirm it with the "<ENTER>" key. Monitor=1 Test=2 Single=1 Cont.=2
Tools=4
A complete description of all the parameter can be find in the FCM Service Tool Reference In order to get access to the Setup or ADAM menu press SHIFT & 7. The Display
document. changes to:

Monitor=1 Test=2 Single=1 Cont.=2

7 Tools (keys: 34) Setup=3 Tools=4 ADAM=3
Initiate test runs commanding the DCSS by SVT and publishes diagnosis information.
SHIFT & 3:
Controlling the door via the service tool or having remote access by the ADAM tool is
-Shortcut to achieve immediately the SysCfg Sub-Menu.
possible only if the Top of Car Inspection switch 'TCI' is set.
-Additional information if stay in Eventlog-Actual menu
Use this feature for installation and maintenance purpose.
 No.: :GAA31064AAA_STM No.. :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 8/28 Engineering Center Service Tool User's Guide Page : 37/28
Berlin Berlin
DCSSS Date: 2007-01-19 DCSSS Date: 2007-01-19
Service Tool Manual Service Tool Manual

SHIFT & 5:
to unlock the DCSS if it stays in locked mode caused by a fatal error (failed interface check
or motor protection). Another way to unlock the system is to power off/on.
6.3 Parameter Setup - Field - (key 333)
( DCSS 5 offers two profile sets each containing a normal opening, a normal closing and Ini
profiles. Standard is profile set 1. The second profile set is used only on elevator controller
request.

The menu Field is a container for parameters related to both profile sets which could be
touched in order to adapt the door performance on the expectation of the customer. For
example modify opening and closing times, creep speeds etc..

The parameter input is checked to a certain degree by the DCSS before it is overwritten by
a new value. During the parameter entering the value is checked against the upper and
lower limit. If the parameter exceeds this limit, the max allowed value will be set instead.

[ Profile Setl 1
Profile Set2 = 2
I
Example:

~1: Open RunTime

~3000ms > _ __
I
enter a new value and confirm it with <ENTER>

General:

pa:bbbbbbbbbbbbbbb
( ( fCCCC dd > __
{

aa: P1 indicates profile set 1, P2 indicates profile set 2

bbbbbbbb: name of set up parameter
ccccc value stored in flash
dd unit
place holder to enter a new value

Scroll to next parameter with <GOON/GOBACK>

A complete deSCription of all the parameter can be find in the FCM Service Tool Reference
document.

I
~
 No.. :GAA31064AAA_STM No.. :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 36/28 Engineering Center Service Tool User's Guide Page: 9128
Bertin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

6.1.2 Set Default (key 3319) 3.3 MODULE Operations

In case of wrong SETUP you can rewrite the system parameter by a set of default
parameter. Take attention that the OCSS is in Service Mode (TCI is set to Inspection).
( (­ The following action will be taken when the "MODULE" key on the service tool panel is
pressed:
Set Defaults? I
<1> Yes No <0> I
~elcome to DCSS

After confirmation following displays appear:

~ess Button =3
J
Setting Defaults 3.4 FUNCTION Operations
Please wait !
When the key "3" is pressed in MODULE operation or when the "FUNCTION" key is
pressed at lower layer of the hierarchy, the follOwing display will be monitored:
Writing Config
Pease Wait!
-------­
j onitor = 1 Test =2
Tools;;:4

To get the SETUP menu please enter -shift & 7­

6.2 First Installation Profile 2 (key 332)
Test =2
If the main controller supports a second speed profile, the OCSS 5 has to perform an Tools=4
additional Installation Run for the second profile. The procedure to determine the profile
and torque parameter is exactly the same as for the first profile, with exception of not
having a configuration setup and bypassing the step 1, 2 and 3 of the automatic installation
run. The condition to start the 2nd.-Profile Installation is a successful Setup with profile 1. (
(
If a key "1" to "4" is pressed the operation shifts to the SET menu level.

For the Monitor Function see chapter 4

For the Test Function see chapter 5
For the Setup Function see chapter 6
For the Tools Function see chapter 7
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
seN. :GAA31064AA
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page . 10128 Engineering Center Service Tool User's Guide Page : 35/28
Berlin Berlin
DCSSS Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

3.S SET Operations

Step 4: Learn Inspection Torques:
All operations are described in the following paragraphs. DeSS 5 opens the door with inspection speed and finds the minimum torque necessary to
open the door completely. In case that the tracking behavior is out of a tolerable range, the
( ( test will be repeated applying an increased torque value. All the creep torques as well as
the close torques are derived for the investigated inspection torque value.
Insp. Torque Cbk
Please wait!

If the learned torque is sufficient to open the door completely, the DeSS closes the door
again to be prepared for the next step.

door is closing
Please wait!
I
Step 4 is finished if the door is fully closed and following display appears:

Prepare Profiles
Please wait!

Now the learn run is finished and the complete evaluated data will be stored permanently
into the Flash

( (
r Writing Config
Please wait!
I
Congratulation! If you reach this point you have successfully installed the DCSS 5.

Attention:

If the installation was not successful the DeSS remains in the RED (reduced) mode. Only
slow profiles can be executed.

For error route cause analysis refer to the Trouble Shouting Procedures in the FCM
Appendix Trouble Shouting Guide'
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 34/28 Engineering Center Service Tool User's Guide Page : 11/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual Service Tool Manual

Step 2 Learn Doorway:

4 Monitor Function (keys: 31)
The DCSS 5 first closes the door and than opens it completely. The accumulated encoder­
When the key "1" is pressed in FUNCTION operation or when the "<SET>" key is pressed
increments during the opening procedure represents the door way.
at lower layer of the hierarchy, the following display will be done:

Door is opening?
[ Please wait!
J Status = 1 Input::: 2
Output::: 3 Comnd;::4

If door is fully open the following question must be answered:

Pressing the keys "1" to "4" at this time the operation will shift to the corresponding field.
Door is opened? Under key 4 you find a hidden menu which only operates when DCSS is configurated for
<1> YES <0> NO Multidrop communication.

If you answer with YES the door starts closing to prepare for the next step.
4.1 Status Display (keys: 311)
Door is closing
Please wait! In all Sub-menus the first display line is used to show the DCSS status information: In the
second line the actual position of the door will be displayed.

I~mmm ccccc sss

Step 3:Leam Creep Ways: (door specific)

rOOmm
J
This step is performed only if the locking segment is required by the selected door type. For
the D0200-2 door system the Lock Distance is hard coded and must not be learned. Description of the first status display line:
The DCSS 5 learns the locking distance and the torque necessary to open and close the mmmm DCSS mode
lock. The start open creep way and close creep way are derived from the locking distance. (
The door opens a short way and closes it for several times ( SERVICE = DCSS is in Service Mode (TCI is active), setup and test runs are
permitted. The DCSS executes
Lock Dist Check SVT door commands only ..
Please wait!
J WORKING DCSS is in normal mode (TCI & EDS inactive) and the system is
installed. All functionality is
available.
NOTSTOP = Door is de-energized, caused by active TES
If the learned creep way is finished DCSS 5 goes to the next step:

cccccc = DCSS operating status:

ROY Door position valid executing normal profiles

SHD Door stopped and de-energized because of a critical event or after power up.
RRM resume ready mode after position error (performing reversal profile)
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STMI
OTIS Software Basic Data
seN. :GAA31064AA
1
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 12/28 Engineering Center Service Tool User's Guide Page : 33/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual I
Service Tool Manual

INI = Door position is not valid, executing slow In i-profiles If the door is fully open its starts closing:
OED Door is de-energized
RED = Reduce operation when system is not installed executing slow Ini profiles iDoor is clodog
only
LCK Locked DCSS I case of a serious event - system continuously de-energized, maintenance required [
Please wait!
J
Tum the DCSS power supply off and than after 5 sec again on, to unlock the system. (or use SVTO ,
hidden key: "shift &5"
If the door is fully closed following question must be answered:

I Door is closed?
<1> YES <0> NO
J

( (
 No.. :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 32128 Engineering Center Service Tool User's Guide Page : 13128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

sss door movement status:

Ooorwidth: enter the physically width of the door in [mm]. The displayed default value is <> opening
900. To overwrite it enter new value and confirm it wit <ENTER>. <P> = opening caused by Passenger Protection (PP)
<0> opening caused by Door Open Button (OOB)
Doonvidth <R> = opening caused by Reversal Device (REV)
00900mm > >< closing
<ENTER> [] opened
][ closed
[1] door is maybe opened (position not valid e.g. so far unknown)
]1[ door is maybe closed (position not valid e.g. so far unknown)
>1< door is stopping
I door is stopped
After the complete declaration of the environment components the DCSS 5 continues with status after power on
the automatic learn run procedure for the profile set 1 . 111 door movement unknown, for example if encoder has been damaged

Description of the second line display:

Step2: Automatic Installation of Profile Set 1
If the Configuration has been finished successfully, an automatic Installation routine will be The door position is calculated according to the speed encoder pulses and is displayed in
started to evaluate the optimum profile parameter. This routine consists of 5 items: [mm]. It corresponds to the door way and is 'Omm, if the door is fully closed.
1: Sense Test: Go Back with Function Key 'Module', 'Function' or 'Set'.
The DCSS learns the cabling sequence of the motor and the encoder.

The DCSS tries to open or close the door. If the system does not detect within a certain 4.2 Input Status Display (keys: 312)
time period a sufficient door movement its reverses automatically the direction. If there is no
movement in both directions the torque will be increased and the test loop starts again. If This set is used to display the actual system state and the discrete input information. The
even with the maximum torque no door movement takes place the installation routine input information depends on the selected controller interface
aborts with the error message Sense Test Failed
The different number fields in the display show the discrete inputs, lower case letters
represent the state "off', upper case letters the state "ON".
( (
Prep SenseTest General: ,..--_ _ _ _ _ _ _----,
[ Please wait! Status display
I first display use GOON
Status display

test fails:
This message will be displayed if the second display
I
Sense Test failed
Door is opening? 4.2.1 3-Wire Standard
I<1> YES <0> NO
if failed, start again> [ <ENTER>
I first display
IDo Config again: ST1
ST2
ST1
ST2
control line 1 of RS-board
control line 2 of RS-board
Watch the door movement and answer the question.
l <ENTER> I ST3 ST3 control line 3 of RS-board
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 14/28 Engineering Center Service Tool User's Guide Page : 31128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

second display Door Type: select door mechanism

(cmd) decoded command of the 3-wire interface (ST1-ST3)
REV reversal signal (EDP or lRD)
I> D2000-2 TLD
Example: (­
D2000-2 CO>
I <ENTER>

/W'orking RDY Working RDY H ,

][ > ,
~Tl stl ST3 (CLD) rev>
use GO ON
The selected door type declares the standard motor and the standard encoder for this kind of door:
,--- -­

Door Type Motor Encoder

'
D2000-2 TLD & CO & C04 FBA24350ACI (200W.l FAA633A2 (500 pulses per/round)
~Q2000 TLD & CO FBA24350Fl (lOOW) F AA633A2 (500 pulses per/round)
SIT9692 TLD & CO FBA24350Fl (IOOW) FAA633A2 (500 pulses per/round)
HSDSTLD&CO FBA24350ACI (200W) FAA633A2 (500 pulses per/round!
AADS Door TLD & CO ADS Motor (l50V) Encoder (500 pulses per/round

Finish Configuration: "YES" starts immediately the learn run. "NO" permits to modify the
motor and
encoder type.

r <11>
Start Auto Learn
YES NO <0>
J
if "NO" is entered

Motor: you can choose 2 motor types.

( IMotor:
Select
motor ttl!e j <ENTER>

select motor type . D02000 I HSDS I KOREAN (for ADS door) with <GO ON > key

with <ENTER> you confirm the selection and come to the next step.

Encoder: enter the pulses per round of the applied encoder.

I Tacbo ReSolutiO
00500ppr > __
d <ENTER>
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 30128 Engineering Center Service Tool User's Guide Page: 15/28
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007..Q1-19
Service Tool Manual Service Tool Manual

Control signal description table:

I ST1 ST2 SI~ REV Door ~v .............

If Relay has been chosen additional parameter have to be set after the automatic learn run
under menu 3-3-4-5 (Relay). 0 0 0 X OED &EDS emergency door stop
0 0 1 X OED TCI, command by SVTOOL
0 1 X X CLD close, PassProt. and Rev disabled
1 0 0 X NDG nudging, Pass Prot + Rev disabled
1 0 1 0 CLD&REV close, PassProt + REV enabled
1 0 1 1 CLD&REV open due to Rev device activated
1 1 X X OPN open

4.2.2 3-Wire Extended (DOB_FAST)

first display
ST1 ST1 control line 1 of RS-board
ST2 ST2 control line 2 of RS-board
ST3 ST3 contro/line 3 of RS-board
DOB Door Open Button

second display
(cmd) decoded command of the 3-wire interface (ST1-ST3)
REV reversal signal (EDP or LRD)
SGS safety gate shoe

Example:

~Orking RDY )( i<;rkin

g RDY
Tl st2 ST3 DOB (CLD) rev SGS>
][ >1
use GOON

Control signal description table:

( Extended 3-Wire Interface with DOB and (SGS):

I ~T ST ST RE
2 3 V
DO
B
PP SGS
note1
Door
Command
Comme
nts

0 0 0 X X X X DED& emergency door stop

EDS
0 0 1 X X X X STOP fCI, command by SVTOOL
0 1 0 X 0 X 1 CLD&D close DOB enabled, open due
X 1 SGS
X 0 open due to active DOB
0 1 1 X X X X CLD close, PP, DOB & REV
-­
disabled
1 0 0 X 0 X X NDG nudging, PP+ Rev + SGS
X 1 X X disabled
 No.: :GAA31064AAA STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
- I OTIS Software Basic Data
SCN. :GAA31064AA

Engineering Center Service Tool Users Guide Page : 16/28 Engineering Center Service Tool User's Guide Page : 29/28
Berlin Berlin
DCSS 5 Date: 2007-01-19 I DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual
I

oRen due to active DOB

1 0 1 0 0 0 0 CLD&RPD close, PP, DOB &REV enabled
1 0 0 0 open due to active REV signal 6.1.1 Configuration (keys 3311)
o 1 0 0 open due to active DOB signal Step 1: Declaration of the environment components:
o 0 1 0 open due to active PP ( (­ In the first step DCSS 5 asks for the declaration of the environment components. The
o 0 0 1 open due to active SGS volume of the configuration setup depends on the selected interface. With the arrow, quite
1 1 0 0 X 0 CLD & RP close, PP & REV enabled left on the display, the item can be selected. To change to another item use
1 X 0 0 open due to active REV <GOON/GOBACK> .
o X 1 0 open due to active PP After selection confirm it by <ENTER> and the next component is available.
o X 0 1 open due to active SGS
r- 1 - ' f T- -X- ~·-X~ X X OPN open Interface: 3-Wire or Multidrop:
'nOte1 iSGs function only available with-OCSS5 SW Version GAA30328AAE or higher
, Interface-
3-Wire
--I >

use <GOON>
Interface
3-Wirew. DOB >
use <GOON>
Interface
Multidrop >
use <GOON>
G°terface
Relay
>1
( ( Select an Interface pressing <ENTER> .

If Multidrop has been chosen you will ask for:

DCSS - address:

DCSS-Address
1
DCSS-l >1 <ENTER>

with <GOON> you can select DCSS-1 up to DCSS - 4.

DCSS-1 is generally used for a front door system. DCSS-2 for an alternate one.
 No.: :GAA31064A.AA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool Users Guide Page: 28128 Engineering Center Service Tool User's Guide Page : 17/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual Service Tool Manual

4.2.3 Multidrop
Use the keys "SET", "FUNCTIOW or "MODULE" to interrupt the installation routine. first display
LRD light ray reversal device
EDP electronic door protection reversal device
( ( SO safe to open signal
DOB door open button

second display
TDOB Top of Car Door Open Button (BS7255)
TDCB Top of Car Door Close Button (BS7255)
(mcd) door command, received from multidrop serial link

Example:

~Orking RDY
rd EDP SO dob 1l > I use GO ON
~;rking RDY ][
(OPDt) tdob tdeb >
I

Reversal inputs in operation:

I DOB I LRD I EDP I
_........... ------............------......._---- ...........""--_.._-- ...-......-
DEDt deenergize(EDS) 1 ----­ I ----­ I .......... I set on EDS
DED2 = deenergize(TCI) I ----­ I ----­ 1 I seton TCI
OPDl = open door I ----­ I -.._..... I ......-­ I (normal profile)
OPD2 open door I ---­ I I ----­ I (second profile)
CLDt close door I --..._­ I ... ---­ I I
CLD2 close door I D I L I E I
= I I I e I
( ( CLD3
CLD4 =
close door
close door I
D
D I
L
I I e I
CLD5 nudging I D I ..........­ I --_. I
CLD6 close door I D I ---­ I e I
CLD7 = stop I ...... _-­ I ---_ .. I ...,........ ­ I (new)
CLD8 = close door I d I I ----­ I
D full! d limited door reversal, _.- no door reversal on DOB
L full! I limited door reversal, - no door reversal on LRD
E full! e limited door reversal, --­ no door reversal on EDP

--­
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 18/28 Engineering Center Service Tool User's Guide Page : 27128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

When the key "3" is pressed in FUNCTION operation or when the "SET" key is pressed at
lower layer of the hierarchy, the system will shift to the setup function and the following
4.2.4 Relay (with Interface Box) display is shown:
first display
DO door open command ( lnStl=l Inst2=2
NDG
TCI
EDS
nudging command
top of car inspection signal
emergency door stop signal
IField=3 Eng=4

second display: Pressing the keys "1" to "4" at this level, you will shift to the corresponding field and a
2nd prof second profile signal (depends on setup) changing of the setup parameters is possible.
DOB door re-open signal
A list of all setup parameters and their value range is shown in the FCM Service Tool
Example: Reference manual.
,-o-r-k-in-g--RO--Y----]-[-.
DO ndg tei eds >
use GO ON
IWorking RDY
L:ndprof dob ][ > I Attention:
To enter a new value or to run the Installation routine the DCSS must be in the Service
mode by switching TCI to inspection. An active TES signal or losing TCI interrupts
immediately any setup action.

Prior to a successfuilNST1 installation the DCSS5 operates in a reduced mode e.g. the
door is running with low speed only.

4.3 Output Status Display (keys: 313) A parameter is stored permanently in the Flash memory not before the menu is left with one
of the function key (Module, Function or Set).

This set is used to display the actual system state and the discrete outputs.
6.1 First Installation Profile 1 (key 331)
Example:
For the first time the DCSS is set into operation the DCSS must run an Installation routine
I to find the optimum system parameters for that specific door mechanic and the electrical

lWORKING ROY [)
DOL dos ( ( environment.
The complete 'Installation Menu' runs partly automatically. Only few confirmations have to
be entered by the user.
In order to simplify the installation the complete procedure is menu-driven and displayed on
General: the Service Tool. The user only needs to follow the displayed instructions and has to
confirm the questions. In the first step the DCSS5 asks for the declaration of the
I Status display environment components and in a second step it executes an automatic learn run for the
~l 222 > profile set 1 .
To run the SETUP Routine the system must be set into the Service mode (TCI is set).
Before the installation can start, the 3-Wire Interface has to be checked against incorrect
The different number fields in the display show the discrete outputs, lower case letters wiring and malfunction.
represent the state "off', upper case letters the state "ON" If the main controller supports a second profile, the same installation must be executed with
the Inst2 menu
For the 3 Wire Intetface the outputs are:
config=l
JSetDef=9 I
 No.. :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page .26128 Engineering Center Service Tool User's Guide Page . 19/28
Berlin Berlin
DCSSS Date: 2007'()1·19 DCSSS Date: 2007'()1·19
Service Tool Manual Service Tool Manual

1111 DOL (Door Open Limit). will be set if the door has reached the fully open
S.S System Configuration (keys:325) position
2222 DOS (Door Opening Signal), will be set if the DCSS starts a reversal,
In this menu the actual environment configuration can be shown . To reprogram the caused by the internal stalled door protection
configuration use the SETUP menu.

Motor:
Tacho:
D02000
500ppr >
I
I
<GOON/GOBACK>
HSDSNY TLD
900mm

<GOON/GOBACK>

Motor: D02000 / HSDS/Korea

Encoder pulses per round
Doortype: D2000-2 TLD/CO/C04, D02000 TLD I CO, HSDS NY TLD I CO. ADS
DOORTLD/CO
Doorwidth : in xxxx [mm]
Interface: 3-Wire , 3-Wire w. DOB, Multidrop, Relay
if multidrop serial link interface:
Address: DCSS-1 ...4
Line terminator LTerm: ON/OFF
(
6.0 Setup Function (keys: 33)

Attention:
If the SVTOOL is connected for the first time, the SETUP menu does not appear on the
display. Please enter shift & 7 to make visible the SETUP menu

rODitOr=l Test=2
Tools=4
J <SHIFT & 7>
onitor=l
Setup=3
Test=2
Tools=4
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STMI
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 20/28 Engineering Center Service Tool User's Guide Page : 25128
Berlin Berlin
DCSS5 Oate: 2007-01·19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

If the check has been started it will prompt after some seconds the following message if no errors has been detected:
For the Relay Interface the state of the outputs of the Relay Interface Box are displayed:
REL1 (DOL: door fully open)
REl2
REl3
REl4
(DCL: door fully closed)
(GH: depends on SETUP - Param 'EFS-Operation')
(SGl: door opened I closed)
( I Interface OK !
<ENTER>
I
In case of an error. the DCSS goes into a Locked State and shows the cause of the failed check. For more detaHs see
REL5 (PMY: door closed) SVTOOL Reference List.
REl6 (if SGS input has been activated) Correct the wiring and start the Interface Check again.

For the Multidrop Interface there are no discrete outputs available.

4.4 Command Status Display (keys: 314) (hidden)

This feature is handled differently depending on the selected interface.

4.4.1 3-Wire Standard and Extended and Relay Interface:

This service is not available for all the DCSS with a 3-wire interfaces.

~
-~--

Currently not
~ilable ...

4.4.2 Multidrop Serial Link Interface:

With this function an actual screen shoot of the serial receive buffer of the DCSS5 will be (
displayed for analyzing the multidrop serial link. There will be displayed the first 8 bytes in
HEX format. With <GOON> you see the next 8 ones.
With the next start of scroll the display will be updated with the new buffer content.
_WOOGWMm I~WOOGWMm
04:390 FF 00 43 6F 3B > use <GOON> ~C:3 90 FF 00 43 6F 3B

~ - - . -....... ~
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 24128 Engineering Center Service Tool User's Guide Page 21/28
Berlin Berlin
DCSSS Date: 2007-01-19 DCSSS Date: 2007-01-19
Service Tool Manual Service Tool Manual

powered off. So this time represents the over aU living time of the DCSS5. The format is:
hours:minutes:sec 5 Test Function (keys: 32)
When the key "2" is pressed in FUNCTION operation or when the "SET" key is pressed at lower layer of the hierarchy. the
[Systc...m. Time: following display will be made:
l0043h12m36
- _........................................................_.. _.. _.. _._.­

Event = 1 Maint. 2 <GOON/GOBACK> IntrfChk = 4

First: (keys 32132):
Last: (keys 32133): I Part =3 >
I SysCfg= 5 >[
The events are stored in the order of their appearance. An included logging time stamp gives the relation to the present
You can start the History-list from the first enlfy of the event logging or from the last one. To scroll through the history list time (available under 3-2-1-3).
use <GOON/GOBACK>
Pressing the keys "1" to "5" at this time the operation will shift to the corresponding field.
~O.l...: s...tart of Log
Il!lh28:53 [
5.1 Event Menu Display (keys: 321)
With pressing the key "1", you reach the event-submenu. The event logger is used to display infonnation about detected
5.1.4 Del display (keys: 3219) events. There are 3 different types of storing the events.

With this function the complete event logging entries can be deleted. Be attention that the TCI switch is set. A warning Actual =1 EvLog = 2
appears and the user must confinn the action.
Del = 9
5.2 Maintenance (keys: 322)
I History = 3

It displays the accumulated OCSS operation time and is used for long tann live-time supervision. The fonnat of this 5.1.1 Actual display (keys: 3211)
maintenance time is : 'hours:min:sec days years'. The Actual event shows the 16 very last events, starting with the oldest event. A time stamp is included. These events are
With <GOONIGOBACK> the absolute amount of complete door runs will be displayed. not stored persistent and will be lost after power down. Additional information will be displayed with pressing 'shift 3'.
EXAMPLE
alive: I <GOON/GOBACK> [ Total cycles:
[ 126 Open ~i~eouhJ
16:28:53 223 01 > 2600 126 <>
0001 0000:43:12 OPN 0OO0836mm
<shift 3>
5.3 Partnumber (keys: 323)
Shows the actual software configuration number and the date of release. I I GENERAL:
( (
GAA30328AAC
(date) abb event name •.•• abb sss.... !
I ccccc hhhh:mm:ss <shift 3>
uuu xxxxxxxxxx
5.4 Interface Check (keys: 324)
This function starts a long interface check-sequence to test the discrete 3-wire interface. Use this feature if any
communication problem between DCSS and LCBIIITCB occurs. Be attention, that the TCI switch is set, otherwise the
check will fail! abb event 10 number, consist of Event Class and the event number:
Every time a check is started, the DCSS sends a request to the LCBITCB by setting both outputs active (DOL = ov, DOS Event Classes are:
:; 24V). Within a time interval of 400ms the controller sends a pulse pattern to the DCSS. If the DCSS detects wrong I :; Information only: results from nonnal operation. For example: logging of the power up event, reversal
command signal line level transition it repeats the check sequence 3 times again. In case that all attempts fail, the DCSS operation etc.
switches into the locked mode. In this mode the DCSS ignores the received discrete interface commands. =
W Warning: For Maintenance purpose only. The DCSS is able to handle the situation. The
perfonnance is not affected. Inspection is recommended, tor example 'Logging FuU'.
Check Interface?
=
E Error: Maintenance requested: serious event, performance degradation expecled,
Tet is set? for example : '3-WireComFail'.
<1>YES NO<O>
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 22/28 Engineering Center Service Tool User's Guide Page : 23128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

A detailed description of the event numbers -;!nd names can be found in the Service Tool Reference US!. The different fields in the second display line show:
cccc = number of runs
hhhh:mm:ss timestamp of last event, the time is related format is:
hours:minutes:seconds
sss OCSS door movement status (see Monitor - Status)
( uuu = OCSS operation status (see Monitor - Status)
xxxxxxxx the actual position during the event has been logged

Press <GO ON> or <GO BACK> to scroll through the events, which occurred since the last
system reset.
NOTE: The actual events are not stored permanently! They are lost after
disconnecting the main power.

5.1.2 EvLog display (keys 3212)

This event logging display shows the cumulated occurrences of each event with a logging
time stamp information about detected errors. This time stamp shows how much time is
gone from now to that time the event has been occurred.
These events are stored persistent. They can be deleted by function 'Del' (key 3219).
EXAMPLE:

126 Open Timeout

001 .. OOOO43hI2

The first line shows the event 10 number and the name of the event. In the second line the
amount of occurrences and the time which nas been gone after occurrence. This
representation is the same as known from the OCSS4.

Press <GO ON> or <GO BACK> to scroll through the errors, which occurred since the last
( ( II system reset.
5.1.3 History display (keys 3213)
In this history list all events are logged in order of their appearance. An included logging
time stamp gives the relation to the present time.

fTime=l First = 2/
I Last = 3
Time: (keys 32131)
This System Time is the reference for the History- and Actually-Event logging time. The
time is hold persistent and will be initialized with the last value before the DCSS was

-'--­
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 22/28 Engineering Center Service Tool User's Guide Page : 23128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

A detailed description of the event numbers -;!nd names can be found in the Service Tool Reference US!. The different fields in the second display line show:
cccc = number of runs
hhhh:mm:ss timestamp of last event, the time is related format is:
hours:minutes:seconds
sss OCSS door movement status (see Monitor - Status)
( uuu = OCSS operation status (see Monitor - Status)
xxxxxxxx the actual position during the event has been logged

Press <GO ON> or <GO BACK> to scroll through the events, which occurred since the last
system reset.
NOTE: The actual events are not stored permanently! They are lost after
disconnecting the main power.

5.1.2 EvLog display (keys 3212)

This event logging display shows the cumulated occurrences of each event with a logging
time stamp information about detected errors. This time stamp shows how much time is
gone from now to that time the event has been occurred.
These events are stored persistent. They can be deleted by function 'Del' (key 3219).
EXAMPLE:

126 Open Timeout

001 .. OOOO43hI2

The first line shows the event 10 number and the name of the event. In the second line the
amount of occurrences and the time which nas been gone after occurrence. This
representation is the same as known from the OCSS4.

Press <GO ON> or <GO BACK> to scroll through the errors, which occurred since the last
( ( II system reset.
5.1.3 History display (keys 3213)
In this history list all events are logged in order of their appearance. An included logging
time stamp gives the relation to the present time.

fTime=l First = 2/
I Last = 3
Time: (keys 32131)
This System Time is the reference for the History- and Actually-Event logging time. The
time is hold persistent and will be initialized with the last value before the DCSS was

-'--­
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 24128 Engineering Center Service Tool User's Guide Page 21/28
Berlin Berlin
DCSSS Date: 2007-01-19 DCSSS Date: 2007-01-19
Service Tool Manual Service Tool Manual

powered off. So this time represents the over aU living time of the DCSS5. The format is:
hours:minutes:sec 5 Test Function (keys: 32)
When the key "2" is pressed in FUNCTION operation or when the "SET" key is pressed at lower layer of the hierarchy. the
[Systc...m. Time: following display will be made:
l0043h12m36
- _........................................................_.. _.. _.. _._.­

Event = 1 Maint. 2 <GOON/GOBACK> IntrfChk = 4

First: (keys 32132):
Last: (keys 32133): I Part =3 >
I SysCfg= 5 >[
The events are stored in the order of their appearance. An included logging time stamp gives the relation to the present
You can start the History-list from the first enlfy of the event logging or from the last one. To scroll through the history list time (available under 3-2-1-3).
use <GOON/GOBACK>
Pressing the keys "1" to "5" at this time the operation will shift to the corresponding field.
~O.l...: s...tart of Log
Il!lh28:53 [
5.1 Event Menu Display (keys: 321)
With pressing the key "1", you reach the event-submenu. The event logger is used to display infonnation about detected
5.1.4 Del display (keys: 3219) events. There are 3 different types of storing the events.

With this function the complete event logging entries can be deleted. Be attention that the TCI switch is set. A warning Actual =1 EvLog = 2
appears and the user must confinn the action.
Del = 9
5.2 Maintenance (keys: 322)
I History = 3

It displays the accumulated OCSS operation time and is used for long tann live-time supervision. The fonnat of this 5.1.1 Actual display (keys: 3211)
maintenance time is : 'hours:min:sec days years'. The Actual event shows the 16 very last events, starting with the oldest event. A time stamp is included. These events are
With <GOONIGOBACK> the absolute amount of complete door runs will be displayed. not stored persistent and will be lost after power down. Additional information will be displayed with pressing 'shift 3'.
EXAMPLE
alive: I <GOON/GOBACK> [ Total cycles:
[ 126 Open ~i~eouhJ
16:28:53 223 01 > 2600 126 <>
0001 0000:43:12 OPN 0OO0836mm
<shift 3>
5.3 Partnumber (keys: 323)
Shows the actual software configuration number and the date of release. I I GENERAL:
( (
GAA30328AAC
(date) abb event name •.•• abb sss.... !
I ccccc hhhh:mm:ss <shift 3>
uuu xxxxxxxxxx
5.4 Interface Check (keys: 324)
This function starts a long interface check-sequence to test the discrete 3-wire interface. Use this feature if any
communication problem between DCSS and LCBIIITCB occurs. Be attention, that the TCI switch is set, otherwise the
check will fail! abb event 10 number, consist of Event Class and the event number:
Every time a check is started, the DCSS sends a request to the LCBITCB by setting both outputs active (DOL = ov, DOS Event Classes are:
:; 24V). Within a time interval of 400ms the controller sends a pulse pattern to the DCSS. If the DCSS detects wrong I :; Information only: results from nonnal operation. For example: logging of the power up event, reversal
command signal line level transition it repeats the check sequence 3 times again. In case that all attempts fail, the DCSS operation etc.
switches into the locked mode. In this mode the DCSS ignores the received discrete interface commands. =
W Warning: For Maintenance purpose only. The DCSS is able to handle the situation. The
perfonnance is not affected. Inspection is recommended, tor example 'Logging FuU'.
Check Interface?
=
E Error: Maintenance requested: serious event, performance degradation expecled,
Tet is set? for example : '3-WireComFail'.
<1>YES NO<O>
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STMI
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 20/28 Engineering Center Service Tool User's Guide Page : 25128
Berlin Berlin
DCSS5 Oate: 2007-01·19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

If the check has been started it will prompt after some seconds the following message if no errors has been detected:
For the Relay Interface the state of the outputs of the Relay Interface Box are displayed:
REL1 (DOL: door fully open)
REl2
REl3
REl4
(DCL: door fully closed)
(GH: depends on SETUP - Param 'EFS-Operation')
(SGl: door opened I closed)
( I Interface OK !
<ENTER>
I
In case of an error. the DCSS goes into a Locked State and shows the cause of the failed check. For more detaHs see
REL5 (PMY: door closed) SVTOOL Reference List.
REl6 (if SGS input has been activated) Correct the wiring and start the Interface Check again.

For the Multidrop Interface there are no discrete outputs available.

4.4 Command Status Display (keys: 314) (hidden)

This feature is handled differently depending on the selected interface.

4.4.1 3-Wire Standard and Extended and Relay Interface:

This service is not available for all the DCSS with a 3-wire interfaces.

~
-~--

Currently not
~ilable ...

4.4.2 Multidrop Serial Link Interface:

With this function an actual screen shoot of the serial receive buffer of the DCSS5 will be (
displayed for analyzing the multidrop serial link. There will be displayed the first 8 bytes in
HEX format. With <GOON> you see the next 8 ones.
With the next start of scroll the display will be updated with the new buffer content.
_WOOGWMm I~WOOGWMm
04:390 FF 00 43 6F 3B > use <GOON> ~C:3 90 FF 00 43 6F 3B

~ - - . -....... ~
 No.. :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page .26128 Engineering Center Service Tool User's Guide Page . 19/28
Berlin Berlin
DCSSS Date: 2007'()1·19 DCSSS Date: 2007'()1·19
Service Tool Manual Service Tool Manual

1111 DOL (Door Open Limit). will be set if the door has reached the fully open
S.S System Configuration (keys:325) position
2222 DOS (Door Opening Signal), will be set if the DCSS starts a reversal,
In this menu the actual environment configuration can be shown . To reprogram the caused by the internal stalled door protection
configuration use the SETUP menu.

Motor:
Tacho:
D02000
500ppr >
I
I
<GOON/GOBACK>
HSDSNY TLD
900mm

<GOON/GOBACK>

Motor: D02000 / HSDS/Korea

Encoder pulses per round
Doortype: D2000-2 TLD/CO/C04, D02000 TLD I CO, HSDS NY TLD I CO. ADS
DOORTLD/CO
Doorwidth : in xxxx [mm]
Interface: 3-Wire , 3-Wire w. DOB, Multidrop, Relay
if multidrop serial link interface:
Address: DCSS-1 ...4
Line terminator LTerm: ON/OFF
(
6.0 Setup Function (keys: 33)

Attention:
If the SVTOOL is connected for the first time, the SETUP menu does not appear on the
display. Please enter shift & 7 to make visible the SETUP menu

rODitOr=l Test=2
Tools=4
J <SHIFT & 7>
onitor=l
Setup=3
Test=2
Tools=4
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 18/28 Engineering Center Service Tool User's Guide Page : 27128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

When the key "3" is pressed in FUNCTION operation or when the "SET" key is pressed at
lower layer of the hierarchy, the system will shift to the setup function and the following
4.2.4 Relay (with Interface Box) display is shown:
first display
DO door open command ( lnStl=l Inst2=2
NDG
TCI
EDS
nudging command
top of car inspection signal
emergency door stop signal
IField=3 Eng=4

second display: Pressing the keys "1" to "4" at this level, you will shift to the corresponding field and a
2nd prof second profile signal (depends on setup) changing of the setup parameters is possible.
DOB door re-open signal
A list of all setup parameters and their value range is shown in the FCM Service Tool
Example: Reference manual.
,-o-r-k-in-g--RO--Y----]-[-.
DO ndg tei eds >
use GO ON
IWorking RDY
L:ndprof dob ][ > I Attention:
To enter a new value or to run the Installation routine the DCSS must be in the Service
mode by switching TCI to inspection. An active TES signal or losing TCI interrupts
immediately any setup action.

Prior to a successfuilNST1 installation the DCSS5 operates in a reduced mode e.g. the
door is running with low speed only.

4.3 Output Status Display (keys: 313) A parameter is stored permanently in the Flash memory not before the menu is left with one
of the function key (Module, Function or Set).

This set is used to display the actual system state and the discrete outputs.
6.1 First Installation Profile 1 (key 331)
Example:
For the first time the DCSS is set into operation the DCSS must run an Installation routine
I to find the optimum system parameters for that specific door mechanic and the electrical

lWORKING ROY [)
DOL dos ( ( environment.
The complete 'Installation Menu' runs partly automatically. Only few confirmations have to
be entered by the user.
In order to simplify the installation the complete procedure is menu-driven and displayed on
General: the Service Tool. The user only needs to follow the displayed instructions and has to
confirm the questions. In the first step the DCSS5 asks for the declaration of the
I Status display environment components and in a second step it executes an automatic learn run for the
~l 222 > profile set 1 .
To run the SETUP Routine the system must be set into the Service mode (TCI is set).
Before the installation can start, the 3-Wire Interface has to be checked against incorrect
The different number fields in the display show the discrete outputs, lower case letters wiring and malfunction.
represent the state "off', upper case letters the state "ON" If the main controller supports a second profile, the same installation must be executed with
the Inst2 menu
For the 3 Wire Intetface the outputs are:
config=l
JSetDef=9 I
 No.: :GAA31064A.AA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool Users Guide Page: 28128 Engineering Center Service Tool User's Guide Page : 17/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual Service Tool Manual

4.2.3 Multidrop
Use the keys "SET", "FUNCTIOW or "MODULE" to interrupt the installation routine. first display
LRD light ray reversal device
EDP electronic door protection reversal device
( ( SO safe to open signal
DOB door open button

second display
TDOB Top of Car Door Open Button (BS7255)
TDCB Top of Car Door Close Button (BS7255)
(mcd) door command, received from multidrop serial link

Example:

~Orking RDY
rd EDP SO dob 1l > I use GO ON
~;rking RDY ][
(OPDt) tdob tdeb >
I

Reversal inputs in operation:

I DOB I LRD I EDP I
_........... ------............------......._---- ...........""--_.._-- ...-......-
DEDt deenergize(EDS) 1 ----­ I ----­ I .......... I set on EDS
DED2 = deenergize(TCI) I ----­ I ----­ 1 I seton TCI
OPDl = open door I ----­ I -.._..... I ......-­ I (normal profile)
OPD2 open door I ---­ I I ----­ I (second profile)
CLDt close door I --..._­ I ... ---­ I I
CLD2 close door I D I L I E I
= I I I e I
( ( CLD3
CLD4 =
close door
close door I
D
D I
L
I I e I
CLD5 nudging I D I ..........­ I --_. I
CLD6 close door I D I ---­ I e I
CLD7 = stop I ...... _-­ I ---_ .. I ...,........ ­ I (new)
CLD8 = close door I d I I ----­ I
D full! d limited door reversal, _.- no door reversal on DOB
L full! I limited door reversal, - no door reversal on LRD
E full! e limited door reversal, --­ no door reversal on EDP

--­
 No.: :GAA31064AAA STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
- I OTIS Software Basic Data
SCN. :GAA31064AA

Engineering Center Service Tool Users Guide Page : 16/28 Engineering Center Service Tool User's Guide Page : 29/28
Berlin Berlin
DCSS 5 Date: 2007-01-19 I DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual
I

oRen due to active DOB

1 0 1 0 0 0 0 CLD&RPD close, PP, DOB &REV enabled
1 0 0 0 open due to active REV signal 6.1.1 Configuration (keys 3311)
o 1 0 0 open due to active DOB signal Step 1: Declaration of the environment components:
o 0 1 0 open due to active PP ( (­ In the first step DCSS 5 asks for the declaration of the environment components. The
o 0 0 1 open due to active SGS volume of the configuration setup depends on the selected interface. With the arrow, quite
1 1 0 0 X 0 CLD & RP close, PP & REV enabled left on the display, the item can be selected. To change to another item use
1 X 0 0 open due to active REV <GOON/GOBACK> .
o X 1 0 open due to active PP After selection confirm it by <ENTER> and the next component is available.
o X 0 1 open due to active SGS
r- 1 - ' f T- -X- ~·-X~ X X OPN open Interface: 3-Wire or Multidrop:
'nOte1 iSGs function only available with-OCSS5 SW Version GAA30328AAE or higher
, Interface-
3-Wire
--I >

use <GOON>
Interface
3-Wirew. DOB >
use <GOON>
Interface
Multidrop >
use <GOON>
G°terface
Relay
>1
( ( Select an Interface pressing <ENTER> .

If Multidrop has been chosen you will ask for:

DCSS - address:

DCSS-Address
1
DCSS-l >1 <ENTER>

with <GOON> you can select DCSS-1 up to DCSS - 4.

DCSS-1 is generally used for a front door system. DCSS-2 for an alternate one.
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 30128 Engineering Center Service Tool User's Guide Page: 15/28
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007..Q1-19
Service Tool Manual Service Tool Manual

Control signal description table:

I ST1 ST2 SI~ REV Door ~v .............

If Relay has been chosen additional parameter have to be set after the automatic learn run
under menu 3-3-4-5 (Relay). 0 0 0 X OED &EDS emergency door stop
0 0 1 X OED TCI, command by SVTOOL
0 1 X X CLD close, PassProt. and Rev disabled
1 0 0 X NDG nudging, Pass Prot + Rev disabled
1 0 1 0 CLD&REV close, PassProt + REV enabled
1 0 1 1 CLD&REV open due to Rev device activated
1 1 X X OPN open

4.2.2 3-Wire Extended (DOB_FAST)

first display
ST1 ST1 control line 1 of RS-board
ST2 ST2 control line 2 of RS-board
ST3 ST3 contro/line 3 of RS-board
DOB Door Open Button

second display
(cmd) decoded command of the 3-wire interface (ST1-ST3)
REV reversal signal (EDP or LRD)
SGS safety gate shoe

Example:

~Orking RDY )( i<;rkin

g RDY
Tl st2 ST3 DOB (CLD) rev SGS>
][ >1
use GOON

Control signal description table:

( Extended 3-Wire Interface with DOB and (SGS):

I ~T ST ST RE
2 3 V
DO
B
PP SGS
note1
Door
Command
Comme
nts

0 0 0 X X X X DED& emergency door stop

EDS
0 0 1 X X X X STOP fCI, command by SVTOOL
0 1 0 X 0 X 1 CLD&D close DOB enabled, open due
X 1 SGS
X 0 open due to active DOB
0 1 1 X X X X CLD close, PP, DOB & REV
-­
disabled
1 0 0 X 0 X X NDG nudging, PP+ Rev + SGS
X 1 X X disabled
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 14/28 Engineering Center Service Tool User's Guide Page : 31128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

second display Door Type: select door mechanism

(cmd) decoded command of the 3-wire interface (ST1-ST3)
REV reversal signal (EDP or lRD)
I> D2000-2 TLD
Example: (­
D2000-2 CO>
I <ENTER>

/W'orking RDY Working RDY H ,

][ > ,
~Tl stl ST3 (CLD) rev>
use GO ON
The selected door type declares the standard motor and the standard encoder for this kind of door:
,--- -­

Door Type Motor Encoder

'
D2000-2 TLD & CO & C04 FBA24350ACI (200W.l FAA633A2 (500 pulses per/round)
~Q2000 TLD & CO FBA24350Fl (lOOW) F AA633A2 (500 pulses per/round)
SIT9692 TLD & CO FBA24350Fl (IOOW) FAA633A2 (500 pulses per/round)
HSDSTLD&CO FBA24350ACI (200W) FAA633A2 (500 pulses per/round!
AADS Door TLD & CO ADS Motor (l50V) Encoder (500 pulses per/round

Finish Configuration: "YES" starts immediately the learn run. "NO" permits to modify the
motor and
encoder type.

r <11>
Start Auto Learn
YES NO <0>
J
if "NO" is entered

Motor: you can choose 2 motor types.

( IMotor:
Select
motor ttl!e j <ENTER>

select motor type . D02000 I HSDS I KOREAN (for ADS door) with <GO ON > key

with <ENTER> you confirm the selection and come to the next step.

Encoder: enter the pulses per round of the applied encoder.

I Tacbo ReSolutiO
00500ppr > __
d <ENTER>
 No.. :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 32128 Engineering Center Service Tool User's Guide Page : 13128
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

sss door movement status:

Ooorwidth: enter the physically width of the door in [mm]. The displayed default value is <> opening
900. To overwrite it enter new value and confirm it wit <ENTER>. <P> = opening caused by Passenger Protection (PP)
<0> opening caused by Door Open Button (OOB)
Doonvidth <R> = opening caused by Reversal Device (REV)
00900mm > >< closing
<ENTER> [] opened
][ closed
[1] door is maybe opened (position not valid e.g. so far unknown)
]1[ door is maybe closed (position not valid e.g. so far unknown)
>1< door is stopping
I door is stopped
After the complete declaration of the environment components the DCSS 5 continues with status after power on
the automatic learn run procedure for the profile set 1 . 111 door movement unknown, for example if encoder has been damaged

Description of the second line display:

Step2: Automatic Installation of Profile Set 1
If the Configuration has been finished successfully, an automatic Installation routine will be The door position is calculated according to the speed encoder pulses and is displayed in
started to evaluate the optimum profile parameter. This routine consists of 5 items: [mm]. It corresponds to the door way and is 'Omm, if the door is fully closed.
1: Sense Test: Go Back with Function Key 'Module', 'Function' or 'Set'.
The DCSS learns the cabling sequence of the motor and the encoder.

The DCSS tries to open or close the door. If the system does not detect within a certain 4.2 Input Status Display (keys: 312)
time period a sufficient door movement its reverses automatically the direction. If there is no
movement in both directions the torque will be increased and the test loop starts again. If This set is used to display the actual system state and the discrete input information. The
even with the maximum torque no door movement takes place the installation routine input information depends on the selected controller interface
aborts with the error message Sense Test Failed
The different number fields in the display show the discrete inputs, lower case letters
represent the state "off', upper case letters the state "ON".
( (
Prep SenseTest General: ,..--_ _ _ _ _ _ _----,
[ Please wait! Status display
I first display use GOON
Status display

test fails:
This message will be displayed if the second display
I
Sense Test failed
Door is opening? 4.2.1 3-Wire Standard
I<1> YES <0> NO
if failed, start again> [ <ENTER>
I first display
IDo Config again: ST1
ST2
ST1
ST2
control line 1 of RS-board
control line 2 of RS-board
Watch the door movement and answer the question.
l <ENTER> I ST3 ST3 control line 3 of RS-board
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STMI
OTIS Software Basic Data
seN. :GAA31064AA
1
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 12/28 Engineering Center Service Tool User's Guide Page : 33/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual I
Service Tool Manual

INI = Door position is not valid, executing slow In i-profiles If the door is fully open its starts closing:
OED Door is de-energized
RED = Reduce operation when system is not installed executing slow Ini profiles iDoor is clodog
only
LCK Locked DCSS I case of a serious event - system continuously de-energized, maintenance required [
Please wait!
J
Tum the DCSS power supply off and than after 5 sec again on, to unlock the system. (or use SVTO ,
hidden key: "shift &5"
If the door is fully closed following question must be answered:

I Door is closed?
<1> YES <0> NO
J

( (
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 34/28 Engineering Center Service Tool User's Guide Page : 11/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual Service Tool Manual

Step 2 Learn Doorway:

4 Monitor Function (keys: 31)
The DCSS 5 first closes the door and than opens it completely. The accumulated encoder­
When the key "1" is pressed in FUNCTION operation or when the "<SET>" key is pressed
increments during the opening procedure represents the door way.
at lower layer of the hierarchy, the following display will be done:

Door is opening?
[ Please wait!
J Status = 1 Input::: 2
Output::: 3 Comnd;::4

If door is fully open the following question must be answered:

Pressing the keys "1" to "4" at this time the operation will shift to the corresponding field.
Door is opened? Under key 4 you find a hidden menu which only operates when DCSS is configurated for
<1> YES <0> NO Multidrop communication.

If you answer with YES the door starts closing to prepare for the next step.
4.1 Status Display (keys: 311)
Door is closing
Please wait! In all Sub-menus the first display line is used to show the DCSS status information: In the
second line the actual position of the door will be displayed.

I~mmm ccccc sss

Step 3:Leam Creep Ways: (door specific)

rOOmm
J
This step is performed only if the locking segment is required by the selected door type. For
the D0200-2 door system the Lock Distance is hard coded and must not be learned. Description of the first status display line:
The DCSS 5 learns the locking distance and the torque necessary to open and close the mmmm DCSS mode
lock. The start open creep way and close creep way are derived from the locking distance. (
The door opens a short way and closes it for several times ( SERVICE = DCSS is in Service Mode (TCI is active), setup and test runs are
permitted. The DCSS executes
Lock Dist Check SVT door commands only ..
Please wait!
J WORKING DCSS is in normal mode (TCI & EDS inactive) and the system is
installed. All functionality is
available.
NOTSTOP = Door is de-energized, caused by active TES
If the learned creep way is finished DCSS 5 goes to the next step:

cccccc = DCSS operating status:

ROY Door position valid executing normal profiles

SHD Door stopped and de-energized because of a critical event or after power up.
RRM resume ready mode after position error (performing reversal profile)
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
seN. :GAA31064AA
OTIS Software Basic Data
seN. :GAA31064AA
Engineering Center Service Tool User's Guide Page . 10128 Engineering Center Service Tool User's Guide Page : 35/28
Berlin Berlin
DCSSS Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

3.S SET Operations

Step 4: Learn Inspection Torques:
All operations are described in the following paragraphs. DeSS 5 opens the door with inspection speed and finds the minimum torque necessary to
open the door completely. In case that the tracking behavior is out of a tolerable range, the
( ( test will be repeated applying an increased torque value. All the creep torques as well as
the close torques are derived for the investigated inspection torque value.
Insp. Torque Cbk
Please wait!

If the learned torque is sufficient to open the door completely, the DeSS closes the door
again to be prepared for the next step.

door is closing
Please wait!
I
Step 4 is finished if the door is fully closed and following display appears:

Prepare Profiles
Please wait!

Now the learn run is finished and the complete evaluated data will be stored permanently
into the Flash

( (
r Writing Config
Please wait!
I
Congratulation! If you reach this point you have successfully installed the DCSS 5.

Attention:

If the installation was not successful the DeSS remains in the RED (reduced) mode. Only
slow profiles can be executed.

For error route cause analysis refer to the Trouble Shouting Procedures in the FCM
Appendix Trouble Shouting Guide'
 No.. :GAA31064AAA_STM No.. :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 36/28 Engineering Center Service Tool User's Guide Page: 9128
Bertin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

6.1.2 Set Default (key 3319) 3.3 MODULE Operations

In case of wrong SETUP you can rewrite the system parameter by a set of default
parameter. Take attention that the OCSS is in Service Mode (TCI is set to Inspection).
( (­ The following action will be taken when the "MODULE" key on the service tool panel is
pressed:
Set Defaults? I
<1> Yes No <0> I
~elcome to DCSS

After confirmation following displays appear:

~ess Button =3
J
Setting Defaults 3.4 FUNCTION Operations
Please wait !
When the key "3" is pressed in MODULE operation or when the "FUNCTION" key is
pressed at lower layer of the hierarchy, the follOwing display will be monitored:
Writing Config
Pease Wait!
-------­
j onitor = 1 Test =2
Tools;;:4

To get the SETUP menu please enter -shift & 7­

6.2 First Installation Profile 2 (key 332)
Test =2
If the main controller supports a second speed profile, the OCSS 5 has to perform an Tools=4
additional Installation Run for the second profile. The procedure to determine the profile
and torque parameter is exactly the same as for the first profile, with exception of not
having a configuration setup and bypassing the step 1, 2 and 3 of the automatic installation
run. The condition to start the 2nd.-Profile Installation is a successful Setup with profile 1. (
(
If a key "1" to "4" is pressed the operation shifts to the SET menu level.

For the Monitor Function see chapter 4

For the Test Function see chapter 5
For the Setup Function see chapter 6
For the Tools Function see chapter 7
 No.: :GAA31064AAA_STM No.. :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 8/28 Engineering Center Service Tool User's Guide Page : 37/28
Berlin Berlin
DCSSS Date: 2007-01-19 DCSSS Date: 2007-01-19
Service Tool Manual Service Tool Manual

SHIFT & 5:
to unlock the DCSS if it stays in locked mode caused by a fatal error (failed interface check
or motor protection). Another way to unlock the system is to power off/on.
6.3 Parameter Setup - Field - (key 333)
( DCSS 5 offers two profile sets each containing a normal opening, a normal closing and Ini
profiles. Standard is profile set 1. The second profile set is used only on elevator controller
request.

The menu Field is a container for parameters related to both profile sets which could be
touched in order to adapt the door performance on the expectation of the customer. For
example modify opening and closing times, creep speeds etc..

The parameter input is checked to a certain degree by the DCSS before it is overwritten by
a new value. During the parameter entering the value is checked against the upper and
lower limit. If the parameter exceeds this limit, the max allowed value will be set instead.

[ Profile Setl 1
Profile Set2 = 2
I
Example:

~1: Open RunTime

~3000ms > _ __
I
enter a new value and confirm it with <ENTER>

General:

pa:bbbbbbbbbbbbbbb
( ( fCCCC dd > __
{

aa: P1 indicates profile set 1, P2 indicates profile set 2

bbbbbbbb: name of set up parameter
ccccc value stored in flash
dd unit
place holder to enter a new value

Scroll to next parameter with <GOON/GOBACK>

A complete deSCription of all the parameter can be find in the FCM Service Tool Reference
document.

I
~
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 38/28 Engineering Center Service Tool User's Guide Page: 7/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

3.2 Key-Function Overview

6.4 Parameter Setup -Engineering ­ (key 334) The Service Tool front panel consists of a display with 2 lines, 16 characters per line, and
16 keys. Some keys have a second function (marked in blue color) which is activated by
This Menu provides access to the installation parameters, which at most of the job-sides { ' pressing SHIFT (first the unlabeled completely blue key which is located directly below
never have to be modified. Anyhow experience shows that there is no way to achieve 1000 ( the SET key) and than the key with the desired function.
coverage for all Job-sides, therefore we want to give you more flexibility. The Engineering­
parameter should be used only by experienced and trained users. For better overview the MODULE:
parameters are separated as following: Guides to the top level menu, the DCSS welcome message- interrupts automatic
installation.
rofl = 1 Profl = 2
FUNCTION:
ntrl== 3 Other = 4
use goon Guides to the second level menu. Inactive during automatic installation.

SET:
Returns from a Sub-menu to the Menu level of ownerShip. Inactive during automatic
Prof1: installation.
Parameters for the standard profile set 1
D/SPIN:
Prof2: Toggles between standard language and alternative language
Parameters for the alternative profile set 2
GO ON I GO BACK:
Cntrl: Navigate through for example a parameter scroll list pressing GOON for the next and the
Closed loop control parameters alternate function GOBACK for the previous list element.

Other: CLEAR:
Container for the rest Erase last entered value.

Relay: SHIFT & 7:

This menu is only available if the interface of DCSS5 is configured as a relay controller. On main menu and Inspection menu level only the following topics are displayed:
Parameter to setup the position controlled output signals.
( ( Main menu: Inspection menu:
Use "<GO ON>" I "<GO BACK>" to scroll through the available setup parameter.
Use the number keys to enter a new value and confirm it with the "<ENTER>" key. Monitor=1 Test=2 Single=1 Cont.=2
Tools=4
A complete description of all the parameter can be find in the FCM Service Tool Reference In order to get access to the Setup or ADAM menu press SHIFT & 7. The Display
document. changes to:

Monitor=1 Test=2 Single=1 Cont.=2

7 Tools (keys: 34) Setup=3 Tools=4 ADAM=3
Initiate test runs commanding the DCSS by SVT and publishes diagnosis information.
SHIFT & 3:
Controlling the door via the service tool or having remote access by the ADAM tool is
-Shortcut to achieve immediately the SysCfg Sub-Menu.
possible only if the Top of Car Inspection switch 'TCI' is set.
-Additional information if stay in Eventlog-Actual menu
Use this feature for installation and maintenance purpose.
 No.: :GAA31064MA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page : 6128 Engineering Center Service Tool User's Guide Page : 39/28
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01-19
Service Tool Manual Service Tool Manual

3 Overview
3.1 Menu Overview ~ingle=l Cont.=2
enter <shift&7>
.~ngle=l
DAM=3
Cont.=21
RESET = 4

( (
I

( (

~
 No.: :GAA31064AAA_SlM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool User's Guide Page: 40/28 Engineering Center Service Tool User's Guide Page.5/28
Berlin Berlin
DCSS5 Date: 2007-01-19 DCSS5 Date: 2007-01·19
Service Tool Manual Service Tool Manual

1 Display and Key Arrangement

7.1 Single ( keys 341) The service tool front panel consists of a display with 2 lines, 16 characters per line, and 16
keys.
Executes single open or close commands. Select between operation with enabled or Some keys have a second function which is activated by pressing first the blue button and
disabled reversal devices. ( ( then the key.
The used key arrangement is as shown below:

!PI: Opn~1 Close=2 ..,

~top=3 RevCls=4 >

use <GOON>

use <GOON> to select 2.Profile commands

2: Opn=l Close=2
top=3 RevCls=4 >

use <GOON>

Following commands can be entered

Open' commands the door to open
Close: commands the door to close (Reversal device & stalled door protection
disabled)
Stop: commands the door to stop
RevCls: commands the door to close but Reversal devices are enabled (
Ndg: command the door to close in nudging mode

Switching to another menu does not interrupt the door movement. Parameter modification
stops immediately the single run.

2 Connection to DCSS
7.2 Continuous (keys 342)
Initiate continuous opening closing operation. Start and stop the continuous run and select When connected to any subsystem, the service tool conducts self-tests and then executes
between operation with enabled or disabled reversal devices . the set-up sequence. The following display will be made when normal communication is
!Continuous Run established with any subsystem.
starts continuous run (reversal devices are enabled)
I.. Start=3 >1
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AAI
OTIS Software Basic Data
SCN. :GAA31064AA
Engineering Center Service Tool Users Guide Page : 4/28 Engineering Center Service Tool Users Guide Page: 41/28
Berlin Berlin
DCSS5 Date: 2007-01·19 DCSS5 Date: 2007-01·19
Service Tool Manual I
Service Tool Manual
,

7 Tools (keys: 34) 38

7.1 Single (keys 341) 40
press <GOON> to disable the reversal devices during continuous run:
7.2 Continuous (keys 342) 40
risab,ed RevDev
7.3 ADAM (keys 343)
( ( Start 3 >1
7.4 RESET (keys 344)

Switching to another menu does not interrupt the door movement. Parameter modification
stops immediately the continuous run.

(
\

I
 No.: :GAA31064AAA_STM No.: :GAA31064AAA_STM
OTIS Software Basic Data
SCN. :GAA31064AA
OTIS Software Basic Data
SCN. :GAA31064AAI
Engineering Center Service Tool User's Guide Page: 42/28 Engineering Center Service Tool User's Guide Page.3/28
Berlin Berlin
DCSS5 Date: 2007.(J1-19 DCSS5 Date: 2001.(J1-19
Service Tool Manual Service Tool Manual

1 Display and Key Arrangement 5

7.3 ADAM (keys 343)
2 Connection to DeSS 5
This is a hidden feature. Pressing Shift & 7 this menu item becomes available.
( (' 3 Overview 6
ADAM stands for Advanced Diagnosis and Maintenance Tool. This is a PC Window based 3.1 Menu Overview 6
software tool, where the PC communicates with the DCSS via the serial link interface
3.2 Key-Function Overview 7
(Multidrop or CAN Bus). To connect the PC with the DCSS, the DCSS must reboot and has
to receive an initialization string from the PC, otherwise the DCSS boots with the normal 3.3 MODULE Operations 9
mode. 3.4 FUNCTION Operations 9
3.5 SET Operations 10
4 Monitor Function (keys: 31) 11
witch to Remote
l>YES NO<O> 4.1 Status Display (keys: 311) 11
4.2 Input Status Display (keys: 312) 13
4.2.1 3-Wire Standard 13
4.2.2 3-Wire Extended (DOB_FAST) 15
4.2.3 Multidrop 17
4.2.4 Relay (with Interface Box) 18
If the systems are connected following features are available:
4.3 Output Status Display (keys: 313) 18
4.4 Command Status Display (keys: 314) (hidden) 20
• On Board reprogramming of the DCSS software download
4.4.1 3-Wire Standard and Extended and Relay Interface: 20
• Load second native language for SVT messages 4.4.2 Multidrop Serial Link Interface: 20
• Upload and download installation parameter sets - archive and duplicate 5 Test Function (keys: 32) 21
installation sets
5.1 Event Menu Display (keys: 321) 21
• Perform long term monitoring of DCSS operation for error root cause analysis 5.1.1 Actual display (keys: 3211) 21
• Collect maintenance information 5.1.2 EvLog display (keys 3212) 23
5.1.3 History display (keys 3213) 23
• DCSS remote control
( ( 5.1.4 Del display (keys: 3219) 24
5.2 Maintenance (keys: 322) 24
5.3 Partnumber (keys: 323) 24
7.4 RESET (keys 344)
5.4 Interface Check (keys: 324) 24
This is a hidden feature. Pressing Shift & 7 this menu item becomes available. 5.5 System Configuration (keys:325) 26

Reset of the DCSS5-E without disconnected the power supply . To proceed it press 1. 6.0 Setup Function (keys: 33) 26
6.1 First Installation Profile 1 (key 331) 27
6.1.1 Configuration (keys 3311) 29
Are you sbure ? 6.1.2 Set Default (key 3319) 36
l>YES NO<O>
6.2 First Installation Profile 2 (key 332) 36
6.3 Parameter Setup ­ Field ­ (key 333) 37
6.4 Parameter Setup -Engineering ­ (key 334) 38