Scribd
Upload
403 views

XWare How To UploadDownload

INSTALACION DE XWARE

Uploaded by

amanecer73mr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
403 views

XWare How To UploadDownload

INSTALACION DE XWARE

Uploaded by

amanecer73mr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 31

How to Upload/Download XWare

At the end of the session you


should be able to:

Use XWare to upload &


download programs from
X language products:
SX, TQ10X,
OEM770X/OEM750X,
BLX/BLHX/BDHX,
PDX/PDHX,
AX,CX,CPLX/CPHX, LX, ZX
2
1. Download & Install X-Ware

2. Connect RS232 serial cable

3. Using XWare: Connect, Upload & Download

2
1. X Series product,
SX shown

2. Serial Cable
3 71-016939-10

4 3. PC with XWare

1 2 (Win XP or prior)
Not compatible with Win7
or newer!

4. For PCs without 9pin


COM port:
USB-to-RS232
Cables Unlimited USB2920
Available at Amazon.com

Motor doesn’t need to be


connected.

3
Download X-Ware
www.parkermotion.com

4
Download X-Ware
www.parkermotion.com

5
Download X-Ware
www.parkermotion.com

6
Download X-Ware
www.parkermotion.com

7
Download X-Ware
www.parkermotion.com

8
Select Utilities > Product

9
Select Utilities > Product

10
11
2
1. Download & Install X-Ware

2. Connect RS232 serial cable

3. Using XWare: Connect, Upload & Download

12
13
Select Utilities > Product

14
Select Product

15
Select Utilities > Product

16
Select Terminal > Setting…

17
Have serial connected and X device powered on.
Click Get available address.

18
Terminal > Connect

19
Terminal > Connect

Type #RV, where # is the address number


This should respond with revision level. This confirms
communication.
Caps lock must be on!
All commands must be preceded by the address number.

#XDIR, where # is the address number


lists the defined sequences within the X product

20
Terminal > Connect
Can’t see what you’re typing?

Type K
Then SSA0
This turns echo on.

Can’t see what you’re typing? Do loopback test...

21
Can’t see what you’re typing?
Loopback test

• Disconnect Tx & Rx from X


• Short these together

21
Loopback test

• Can you see what your typing?


• If yes:
• Perhaps you switched Tx and Rx
• or a sequence is running, reconnect serial,
cycle power on X, type #K 3 times
22 where # is address number
Loopback test

• Can you see what your typing?


• If no:
• Wrong Com port
• Bad cable
• Software conflict
23
Terminal > Connect

Can see what you’re typing but no response?


Then the address number is wrong, or your serial cable
has a short.
OEM products have auto addressing command. Type
#1 to reassign first unit connected to address 1. (It will
respond #2.) Then type 1RV or 1XDIR to check comms.
Try 2RV, 3RV, etc until you get response.

25
2
1. Download & Install X-Ware

2. Connect RS232 serial cable

3. Using XWare: Connect, Upload & Download

26
Terminal > Connect

Type #RV, where # is the address number


This should respond with revision level. This confirms
communication.
Caps lock must be on!

#XDIR, where # is the address number


lists the defined sequences within the X product

27
Terminal > Connect

Type #RV, where # is the address number


This should respond with revision level. This confirms
communication.
Caps lock must be on!

#XDIR,
Select allwhere # is the address number
sequences.
listsshift
Hold theor defined
controlsequences within
key and click the X product
sequences or click All.

28
Terminal > Connect

Type #RV, where # is the address number


This should respond with revision level. This confirms
communication.
Caps lock must be on!

a#XDIR, where # is the address number


lists the defined sequences within the X product

29
Terminal > Connect

Type #RV, where # is the address number


This should respond with revision level. This confirms
communication.
Caps lock must be on!

Connect replacement X product.


#XDIR,
Select allwhere # is the address number
sequences.
Then click Download (down arrow key) in tool bar.
listsshift
Hold theor defined
controlsequences within
key and click the X product
sequences or click All.

30
Terminal > Connect

#XDIR, where # is the address number


lists the defined sequences within the X product

Caps lock must be on!


All commands must be preceded by the address number.

If you cycle power and sequences erased, replace the


battery.

31

You might also like