Republic of the Philippines

Department of Education
MIMAROPA REGION
DIVISION OF CALAPAN CITY
CANUBING NATIONAL HIGH SCHOOL
CANUBING I, CALAPAN CITY

TABLE OF SPECIFICATIONS
Grade 9 TLE- Computer Systems Servicing
QUARTER 3, WEEK 3-4
S.Y. 2021-2022

Item Placement (Bloom’s Taxonomy)

No. of
Module No./Competencies
Items
Remembering Understanding Applying Analyzing Evaluating Creating

LAS 3
10 1-5 6 7 8 9 10 10
 Maintain hand tools

LAS 4
 LO 4. Maintain hand
tools
 Plan and prepare for 10 11-16 17 18 19 20 10
termination/connection
of electrical wiring/
electronics circuits
20 11 2 2 2 2 1 20

Checked by:
PERCIVAL A. AMORADO
Prepared by: Head Teacher IV
HAROLD M. MARTINEZ
Teacher III Noted:
MA. VICTORIA P. MOGOL
Principal III

Canubing National High School

(Santiago V. Uriarte Memorial National High School)
Canubing I, Calapan City/ canubinghs@gmail.com
 Republic of the Philippines
Department of Education
MIMAROPA REGION
DIVISION OF CALAPAN CITY
CANUBING NATIONAL HIGH SCHOOL
CANUBING I, CALAPAN CITY

SUMMATIVE TEST
Grade 9 TLE- Computer Systems Servicing
QUARTER 3, WEEK 3-4
S.Y. 2021-2022

Direction: Choose the best answer. In your answer sheet, shade or blacken the circle that corresponds to
your answer.

1. What 5s is intended to standardize the procedures used to sort, order and clean the workplace?
A. Seiri B. Seiso C. Seiketsu D. Shitsuke
2. Which type of screwdriver referred to as a flat, slotted, or straight screwdriver?
A. Phillips head B. Torx Head C. Hex D. Standard head
3. Which is similar to slip-joint except that they use an elongated hole in the handle with grooves that allow for several
widths?
A. Groove-joint B. Slip-joint C. Needle-nose C. Locking
4. Which type of pliers has two settings in the handle that allow for two widths?
A. Groove-joint B. Slip-joint C. Needle-nose C. Locking
5. What are used to link wires in such a way that they are capable of transmitting data?
A. Crimping tools or Crimpers B. Wire Strippers C. Needle-Nose Pliers D. Wire Cutters
6. What did you observe when using flat, slotted, or straight screwdriver properly?
A. Make sure that the handle is the correct width and thickness to match the screw head slot.
B. Make sure that the material used on the screwdriver match the screw head slot.
C. Make sure that you follow correct rotation when using the tool.
D. Make sure that the tip is the correct width and thickness to match the screw head slot.
7. How would you demonstrate seiton as one of the methods of organization of the workplace?
A. Place all the requisite things in the best position to perform their duties at the workplace.
B. Sort through all items in a location and removing all unnecessary items from the location.
C. Sustain the processes established through self-discipline of the workers.
D. Standardize the procedures used to sort, order and clean the workplace.
8. How would you explain shitsuke as one of the methods of organization of the workplace?
A. Place all the requisite things in the best position to perform their duties at the workplace.
B. Sort through all items in a location and removing all unnecessary items from the location.
C. Sustain the processes established through self-discipline of the workers.
D. Standardize the procedures used to sort, order and clean the workplace.
9. What would happen if you perform proper maintenance on your hand tools?
A. It is implemented to protect the equipment you are working with.
B. It helps prevent accidents and harm to the equipment and people & makes the job easier and less difficult.
C. They'll stay with you in the long run, & will have better performance after every project.
D. It is implemented to protect the health, safety and welfare of all people at the workplace.
10. What alternative would you suggest to sharpen your tools you don’t have diamonds?
A. It's the simplest and cheapest way to go with wire cutter.
B. It's the simplest and cheapest way to go with rock.
C. It's the simplest and cheapest way to go with sandpaper.
D. It's the simplest and cheapest way to go with iron.
11. What is the process of keeping or putting something in a special place while it is not being used?
A. Organizing B. Storage C. Disposal D. Repairing
12. Which mechanism is used to break or pass an electrical current to another conductor?
A. Passive Device B. Switch C. Resistors D. Fuse

Canubing National High School

(Santiago V. Uriarte Memorial National High School)
Canubing I, Calapan City/ canubinghs@gmail.com
13. Which common component, is used primarily inside the circuit to regulate current and voltage?
A. Passive Device B. Switch C. Resistors D. Fuse
14. What device is used to protect the electrical circuit from excessive current effects?
A. Passive Device B. Switch C. Resistors D. Fuse
15. What electronic devices is one that does not add any power gain (amplification) to a circuit or system?
A. Passive Device B. Switch C. Resistors D. Fuse
16. Which law states that the current in a circuit is directly proportional to the total voltage acting in the circuit, for a
constant current, and inversely proportional to the total resistance of the circuit?
A. Voltage Law B. Capacitance Law C. Ohm’s law D. Law of Gravity
17. What differences exist between wires & cables?
A. A cable is a single electrical conductor on the other hand, a wire refers to two or more insulated wires
wrapped in one jacket.
B. A wire is a single electrical conductor on the other hand, a cable refers to two or more insulated wires
wrapped in one jacket.
C. A wire is a double electrical conductor on the other hand, a cable refers to three or more insulated wires
wrapped in one jacket.
D. A cable is a double electrical conductor on the other hand, a wire refers to three or more insulated wires
wrapped in one jacket.
18. How would you demonstrate the proper way in storing instruments?
A. Always store tools in a damp place.
B. Store precision instruments where they can bump against each other in the drawer.
C. Keep measuring instruments stored in a place as far away as possible from vibration and movement.
D. Precision measuring tools should be put near any magnetic material.
19. How would you explain the advantage of hanging Tools or using Tool Storage Drawers in storing tools?
A. It helps protect tools from dust & airborne contaminants and prevent accidental physical damage.
B. It will keep it safe, clean and organized.
C. It will keep instruments off the floor and organized.
D. It is a smart solution for keeping your power tools organized especially if the problem is space.
20. What would happen if you use cases in storing measuring devices?
A. It helps protect tools from dust & airborne contaminants and prevent accidental physical damage.
B. It will keep it safe, clean and organized.
C. It will keep instruments off the floor and organized.
D. It is a smart solution for keeping your power tools organized especially if the problem is space.

Checked by:
PERCIVAL A. AMORADO
Prepared by: Head Teacher IV
HAROLD M. MARTINEZ
Teacher III Noted:
MA. VICTORIA P. MOGOL
Principal III

Canubing National High School

(Santiago V. Uriarte Memorial National High School)
Canubing I, Calapan City/ canubinghs@gmail.com
SUMMATIVE TEST
Grade 9 TLE- Computer Systems Servicing
QUARTER 3, WEEK 3-4
S.Y. 2021-2022

1. C
2. D
3. A
4. B
5. A
6. D
7. A
8. C
9. C
10. C
11. B
12. B
13. C
14. D
15. A
16. C
17. B
18. C
19. C
20. A

Canubing National High School

(Santiago V. Uriarte Memorial National High School)
Canubing I, Calapan City/ canubinghs@gmail.com