EVIDENCE PLAN

Competency
Electronic Products Assembly and Servicing NC II
Standard:

Unit of
Assemble Electronic Products
Competency
Ways in which evidence will be collected:

Observation and Oral

[Check the column]

Demonstration and

Third Party Report

oral questioning
Note: Yong mga nka red papalitan nyo ayon sa
qualification nyo. Yong unit of competency (UC)

Written Test
questioning
ay yong UC din na pinili nyo sa CBLM.

Portfolio
The evidence must show that the trainee…
*Prepares electronics components for assembly
 
*Prepares/Makes printed circuit board modules
 
 Prepares assembly workplace in accordance with
OH&S policies and procedures;

 Follows established risk control measures for
work preparation.

Note: *Critical aspects of competency

Prepared by: CORA M MANGA

(Trainer)

Date : November 3, 2021

Electronic Products Date Developed: Document No.

Assembly and November 3, 2021 Validated by:
Servicing NC II Developed by: Page 1 of
(EPAS)
6
Assemble CORA MANGA
Electronic Products
 DEMONSTRATION CHECKLIST

Candidate Name: Marie Carmelie P. Dayag

Assessor’s Name: Cora Manga
Unit of Competency: Assemble electronic products
Qualification: Computer Systems Servicing NCII

Date of Assessment:
Time of Assessment:

Instructions for demonstration:

Given the necessary materials, tools and equipment, the candidate must be
able to perform the preparing / making PCB modules.

Tools & Materials & Equipment:

Desktop or Laptop computer, laser printer, photo paper, copper clad
laminated board, mini drill machine, household clothes iron, plastic container,
ferric

 to show if
evidence is
demonstrated
During the demonstration of skills, the candidate: Yes No N/A
*Prepared electronics components for assembly
*Prepared/Made printed circuit board modules

 Prepared assembly workplace in accordance with OH&S

policies and procedures.
The candidate’s demonstration was:

 Satisfactory Not Satisfactory

MARIE CARMELIE P. DAYAG CORA M. MANGA

Trainee’s Signature Trainer’s Signature

Date: November 3, 2021

Electronic Products Date Developed: Document No.

Assembly and November 3, 2021 Validated by:
Servicing NC II Developed by: Page 2 of
(EPAS)
6
Assemble CORA M MANGA
Electronic Products
 OBSERVATION CHECKLIST

Candidate Name: Avelino Socrates

Assessor’s Name: Cora Manga
Unit of Competency: Assemble electronic products
Qualification: Electronic Products Assembly & Servicing NCII

Date of Assessment: NOVEMBER 3, 2021

Time of Assessment: 8:00 AM- 5:00 PM

Instructions for demonstration:

Given the necessary materials, tools and equipment, the candidate must be
able to perform the preparing / making PCB modules.

Tools & Materials & Equipment:

Desktop or Laptop computer, laser printer, photo paper, copper clad laminated
board, mini drill machine, household clothes iron, plastic container, ferric

 to show if
evidence is
demonstrated
During the demonstration of skills, the candidate: Yes No N/A
*Prepares/Makes printed circuit board modules

Follows established risk control measures for work

preparation.
The candidate’s demonstration was:

 Satisfactory Not Satisfactory

AVELINO SOCRATES CORA M. MANGA

Trainee’s Signature Trainer’s Signature

Date: November 3, 202

Electronic Products Date Developed: Document No.

Assembly and November 3, 2021 Validated by:
Servicing NC II Developed by: Page 3 of
(EPAS)
6
Assemble CORA M MANGA
Electronic Products
 QUESTIONS
Picture 4
Satisfactory
...
Questions to probe the candidate’s underpinning response
knowledge
Yes No
Extension/Reflection Questions

1. Recall the tools, equipment and materials needed in

 
preparing /making PCB modules.
2. What is the proper way of transferring printed layout to
 
copper clad laminated board?
Safety Questions

1. What are the precautionary measures in handling ferric

 
solution?
2. Why is anti-static wrist band important in assembling
 
electronic devices?
Infrequent/Contingency Questions
1. What will you do if the circuit traces of printed layout did
not completely transfer to the PCB?  

2. What will you do if you have a deadline to finish a CCTV

of a client when there was a sudden brownout in your  
location?
Questions on Rules and Regulations
1. Why are food and drinks not allowed in the work area?  
2. Why do we need to work in a well-ventilated area?  
The candidate’s underpinning  Not
knowledge was:  Satisfactory
Satisfactory
Feedback to candidate:

General comments [Strengths / Improvements needed]:

Electronic Products Date Developed: Document No.

Assembly and November 3, 2021 Validated by:
Servicing NC II Developed by: Page 4 of
(EPAS)
6
Assemble CORA M MANGA
Electronic Products
Candidate’s
Picture 4 signature: AVELINO SOCRATES Date: Nov. 3, 2021
...
Assessor’s signature: CORAZON MANGA Date: Nov. 3, 2021

POSSIBLE ANSWERS

Extension/Reflection Questions

1. Materials, tools and equipment needed in preparing / making PCB modules.

 Desktop or Laptop computer, laser printer, photo paper, copper clad
laminated board, mini drill machine, household clothes iron, plastic
container, ferric chloride solution, permanent black marker, plastic coated
wire, blade cutter, acetone or paint thinner, sanding paper and kitchen
scrubs.
2. Proper way of transferring printed layout to copper clad laminated board.
 Put the copper clad laminated board arranged in layer with glossy photo
paper printed with PCB layout on the clean wooden table with a piece of
maong cloth. Make sure the printed side of the glossy photo paper is facing
to copper clad laminated board.
 Heat up the Electric iron to the maximum temperature.
 Directly press the glossy photo paper using hot iron and apply gentle
pressure for about 5 to 10 minutes.

Safety Questions

1. We need to wear face mask and safety goggles during preparing and making
PCB.
 To avoid tiny grinded particles off the air in doing like in grinding and
cutting of PCB.
2. Safety measure to remember in etching process.
 Wear rubber or plastic gloves to avoid contact with etching solution.
 Wash hands after exposure to hazardous chemicals.
Infrequent/Contingency Questions

1. What if the circuit traces of printed layout did not completely transferred to
the PCB.
 Use permanent black marker to darken the faded track.
2. What if the etching solution was spilled off.
 Wipe it with a cotton clothes, wash with water and wipe it again until its
dry and clean.

Electronic Products Date Developed: Document No.

Assembly and November 3, 2021 Validated by:
Servicing NC II Developed by: Page 5 of
(EPAS)
6
Assemble CORA M MANGA
Electronic Products
 Picture 4 on Rules and Regulations
Questions
...
1. When performing preparation and making of PCB, food and drinks are not
allowed in the work area.
 There’s a presence of live electrical lines in the working area. Spilled
drinks can cause electric hazard when it accidentally contacts with live
electrical wires.
2. Work in a well-ventilated area.
 When working with soldering iron and soldering leads, it produces
unpleasant smell likewise with etching solution. It can harm our
respiratory health. Well-ventilated area can reduce it.

Prepared by:

CORA M MANGA
Trainer

November 3, 2021

Electronic Products Date Developed: Document No.

Assembly and November 3, 2021 Validated by:
Servicing NC II Developed by: Page 6 of
(EPAS)
6
Assemble CORA M MANGA
Electronic Products