TLE-ICT-COMPUTER SYSTEMS SERVICING 9

1. What tool is used to loosen and tighten slotted screws?

A. hex driver
B. torx driver
C. flat screwdriver
D. philips screwdriver

2. It is used to equalize the electrical charge between you and the equipment.
A. anti-static mat
B. anti-static wrist strap
C. flat screwdriver
D. philips screwdriver

3. It is a keyboard shortcut for pasting an item to a document.

A. Ctrl + A
B. Ctrl + B
C. Ctrl + V
D. Ctrl + X

4. It is a process of entering data and programs into the computer system.

A. control unit
B. inputting
C. memory unit
D. outputting

5. It is used to loosen or tighten crosshead screw.

A. flat head screwdriver
B. hex driver
C. phillips head screwdriver
D. torx driver

6.. Which of the following does not belong to the group?

A. central processing unit
B. expansion card
C. motherboard
D. optical mouse

7. The allegator head or clip of the anti-static strap must be clipped or attach
to this ESD tool.
A. anti-static mat
B. computer tables
C. metal part of computer
D. other hand

8. If you are tasked to make simple documentation on the inventory of tools

and equipment used, which software tools is best to be used?
A. database program
B. electronic spreadsheet

Regional Achievement Test –TLE-CSS-9

C. interactive presentation tool
D. word processor

9. To which category does the multimeter belong?

A. cleaning tool
B. diagnostic tool
C. ESD tool
D. hand tool

10. This term refers to the cleaning tool used to organize keyboard and mouse
cables.
A. cable ties
B. lint free cloth
C. multimeter
D. needle nose plier

11. Which component of a computer should be handled with the utmost care
due to its sensitivity to static electricity?
A. graphics card
B. hard drive
C. power supply unit
D. RAM

12. Is the function of the CPU same as the function of the expansion cards or
EC?
A. The CPU interprets and executes user command while the EC enhances
computer performance.
B. The CPU is primarily responsible for storing information while EC is for
erasing them.
C. Both the CPU and the EC are types of computer memory.
D. Both CPU and the EC serves as input device.

13. What device conjoins the two pieces of metal by deforming one or both in
a way that causes them to hold each other?
A. electric hand drill
B. crimping tool
C. long nose pliers
D. soldering Lead

14. Read and study statements below. Which groupings will best help us
ensure safety while using tools?

I – Right tool for the job

II – Reading manuals or usage instructions

Regional Achievement Test –TLE-CSS-9

III – Substituting tools if one is unavailable
IV – Using protective equipment while using tools
V – Putting tools in a single box or storage

A. I, IV and V
B. I, II, and IV
C. II, III, and IV
D. II, IV, and V

15. Select the best restriction would you remind a technician whose task is
to disassemble a computer.
A. wash hands before and after disassembling a computer
B. use only the correct tools in carrying out tasks
C. remove unnecessary jewelries and gadgets
D. wash tools with clean water

16. It is an instrument with jaws clamped around the electric conductor to

measure the current of the circuit.
A. Ammeter
B. Clamp meter
C. Multitester
D. Wattmeter

17. An instrument that can measure the voltage, current and resistance
respectively.
A. Ammeter
B. Clamp meter
C. Multitester
D. Wattmeter

18. It is an instrument used to measure the current in the circuit.

A. Ammeter
B. Ohmmeter
C. Voltmeter
D. Wattmeter

19. This instrument is used to measure the resistance of the circuit.

A. Ammeter
B. Ohmmeter
C. Voltmeter
D. Wattmeter

20. The use of electrical instruments can measure the following factors,
except:
A. current
B. length
C. power

Regional Achievement Test –TLE-CSS-9

D. resistance

21. Power in electricity can be attributed to electrical energy consumed by a

device. What unit of measurement indicates power in electricity?
A. ampere
B. ohms
C. volts
D. watts

22. Which type of testing component is used to check whether an electronic

component is functioning properly within a circuit?
A. continuity testing
B. current testing
C. resistance testing
D. voltage testing

23. The amount of 1,980 watts is equal to __________kW.

A. 0.198 kW
B. 1.98 kW
C. 19.80 kW
D. 198.0 kW

24. The amount of 2,530 Ω (ohms) is equal to __________kΩ.

A. 0.253 kΩ
B. 2.53 k Ω
C. 25.3 k Ω
D. 253 k Ω

25. Electronic devices such as battery, semi-conductor and other electronic

circuits are medium in supplying electricity. Which of the following best
describes the abovementioned devices?
A. the electric circuit flow reverses periodically
B. the electrical outlets supplied with alternating current
C. the movement of electric charge is either in one direction or is
unidirectional
D. the electric circuit flow changes its direction and magnitude which causes
the electricity to counterflow

26. Which of the following functions will serve as the basis in reading the scale
of the multitester?
A. placing test pins to both end of the electronic device being tested
B. recording the numeric value displayed by the scale
C, adjusting the zero-ohm selector knob
D. setting the range selector knob

Regional Achievement Test –TLE-CSS-9

27. What 5S implementation shows to remove unnecessary items and
dispose of them properly?
A. set in order
B. sort
C. standardize
D. sustain

[Link] of the following is the wiring of front panel, except:

A. HDD LED
B. power LED
C. reset switch
D. switch on button

29. It is the cable that passed or saved the information being provided and
process by the computer.
A. Data Cable
B. P4 12V Connector
C. SATA Connector
D. 20/24 pin Molex

30. Which of the following instructs the computer on how to perform basic
functions such as booting, identifying and configuring hardware
components.
A. BEEP CODES
B. BIOS
C. CMOS
D. POST

31. In cleaning computer chassis or box, which of the following tools is used
with a mild cleaning solution?
A. Blower
B. Cloth
C. Duster
D. Lint-free cloth

32. Which of the following computer hardware tool is BEST used to test a
computer port?
A. anti-static strap
B. compressed air
C. loopback adaptor
D. multimeter

33. If you want to add new hardware to your computer, which is the best thing
that needed to be considered first?
A. brand
B. capacity
C. compatibility

Regional Achievement Test –TLE-CSS-9

D. speed

34. If you prefer to trouble shoot your own computer, which technique is best
to do to see the errors within the computer components?
A. replace the whole computer components
B. clean the computer and borrow components to the shop
C. bring the computer to the shop and ask about the error and then fix
D. perform the swapping of components from the working ones

[Link] will you do to properly store computer hardware tools?

A. place on the board/toolkit and labeled it
B. keep inside the box
C. remove faulty tool
D. layered the tools

36. Before repairing computer, which of the following must be consider first
in using the hand tools?
A. check hand tools to be used
B. examine and clean the hand tools
C. never use Personal Protective Equipment
D. select faulty hand tools

37. What makes the BIOS configuration vital in the operation of computers?
A. BIOS prepares the internet connectivity of the computer system
B. BIOS allocates memory to programs, software and files
C. BIOS is responsible in interpreting command from the user
D. BIOS works the initial procedures of a computer start-up

38. Which of the following does NOT describe a successful maintenance

program?
A. defines procedure
B. controls hazard
C. unsystematic
D. well-organized

39. Evaluate the following statements and select the best answer:

Statement 1: Over-tightening screws may cause screw to get stuck on its holes
Statement 2: Turn screws clockwise to loosen screws and counterclockwise to
tighten screws
Statement 3: Stripped screws may still be used but with care

Regional Achievement Test –TLE-CSS-9

A. Only statements 1 and 3 are TRUE
B. Only statements 2 and 3 are TRUE
C. Only statements 1 and 2 are TRUE
D. Only statements 2 and 3 are FALSE

40. Which network type is designed to serve a small area, such as a home,
office, or school?
A. LAN
B. MAN
C. WAN
D. VPN

41. What is the maximum length of a Cat5e UTP cable for reliable data
transmission?
A. 50 meters
B. 100 meters
C. 200 meters
D. 500 meters

42. Which of the following devices is used to connect multiple network

devices and manage traffic flow between them?
A. Router
B. Switch
C. Hub
D. Modem

43. Which type of connector is commonly used to terminate UTP cables for
network connections?
A. RJ11
B. RJ45
C. USB
D. HDMI

44. Which of the following devices is used to provide wireless connectivity to

devices on a network?
A. Router
B. Switch
C. Hub
D. Access point

44. What is the recommended method for checking the continuity of a UTP
cable after terminating it with connectors?
A. Visually inspecting the connectors for correct wiring
B. Using a cable tester to check for correct wiring and signal integrity
C. Measuring the resistance across the connector pins with a multimeter
D. Connecting the cable to a network device and checking for connectivity

Regional Achievement Test –TLE-CSS-9

45. Which of the following tests can a LAN tester perform?
A. Verify the continuity of individual wires in a UTP cable
B. Determine the bandwidth of a network connection
C. Detect network intrusions and security breaches
D. Measure the length of a UTP cable

46. What is the primary purpose of a patch panel in a network infrastructure?

A. To provide centralized management and organization of network cabling
B. To secure network connections and prevent unauthorized access
C. To connect multiple devices to a single network connection point
D. To route network traffic between different subnets or VLANs

47. Which of the following statements is true about a switch in a network

infrastructure?
A. A switch can be used to connect devices on different network segments
or subnets
B. A switch regulates the amount of bandwidth available to each device on
the network
C. A switch is used to connect devices on the same network segment
D. A switch provides backup power in the event of a power outage

48. What is the main difference between Straight-through and crossover

Ethernet cables?

A. Straight-through cables are used to connect devices with different port

speeds, while crossover cables are used to connect similar devices.
B. Straight-through cables are wired differently than crossover cables,
with pins 1 and 2 swapped.
C. Straight-through cables are used to connect similar devices, while
crossover cables are used to connect devices with different port speeds.
D. Straight-through cables are only used for fiber optic networks, while
crossover cables are used for copper networks.

49. What is the main difference between Ethernet and the Internet?

Regional Achievement Test –TLE-CSS-9

 A. Ethernet is a physical networking technology used for local area
networks, while the Internet is a global network of interconnected
computers.
B. Ethernet is a type of internet service provider, while the Internet is a
global network of networks.
C. Ethernet refers to wireless networking, while the Internet refers to wired
networking.
D. Ethernet and the Internet are two different terms for the same thing.

50. Which color code pattern is used for T568A and T568B standards for
wiring Ethernet cables?

A. T568A: Green-White, Green, Orange-White, Blue, Blue-White, Orange,

Brown-White, Brown. T568B: Orange-White, Orange, Green-White, Blue,
Blue-White, Green, Brown-White, Brown.

B. T568A: Blue-White, Blue, Green-White, Orange, Orange-White, Green,

Brown-White, Brown. T568B: Green-White, Green, Orange-White, Blue,
Blue-White, Orange, Brown-White, Brown.

C. T568A: Brown-White, Brown, Green-White, Orange, Orange-White,

Green, Blue-White, Blue. T568B: Blue-White, Blue, Green-White, Orange,
Orange-White, Green, Brown-White, Brown.

D. T568A: Orange-White, Orange, Blue-White, Green, Green-White, Blue,

Brown-White, Brown. T568B: Green-White, Green, Blue-White, Orange,
Orange-White, Blue, Brown-White, Brown.

Regional Achievement Test –TLE-CSS-9

Regional Achievement Test –TLE-CSS-9