Scribd
Upload
22 views

Diassembling and Assembling

This document provides instructions for setting up a network including installing Windows, configuring a router and access point, setting static IP addresses, installing Active Directory and DHCP, creating users and groups, adding a client PC to the domain, enabling remote desktop, and configuring remote access permissions. Key steps include dismantling and inventorying computer components; cabling the router, access point, server, and client PC; installing Windows and drivers; configuring the router and static IPs; installing Active Directory and DHCP; creating a user and group; changing the client workgroup to the domain; installing remote desktop; and unlocking remote user permissions.

Uploaded by

christie j. dulfo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
22 views

Diassembling and Assembling

This document provides instructions for setting up a network including installing Windows, configuring a router and access point, setting static IP addresses, installing Active Directory and DHCP, creating users and groups, adding a client PC to the domain, enabling remote desktop, and configuring remote access permissions. Key steps include dismantling and inventorying computer components; cabling the router, access point, server, and client PC; installing Windows and drivers; configuring the router and static IPs; installing Active Directory and DHCP; creating a user and group; changing the client workgroup to the domain; installing remote desktop; and unlocking remote user permissions.

Uploaded by

christie j. dulfo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

CSS PRE-ASSESSMENT GUIDE

DIASSEMBLING AND ASSEMBLING

1. Remove all the component inside the system unit except mother board
Make an inventory:
Components/materials description
Ex: 2 RAM 2gb/1gb DDR2
Tools
Philips Screw driver
Equipment
Network rack
router
Note: include those that you used in cabling and in server configuration

CABLINGS
2. Cabling connections:
a. Router  patch panel hub
b. access point patch panel hub
c. server pc patch panel hub
d. hub client pc

INSTALLATION
1. Reset router and access point
2. Install windows 2008 r2 and check drivers if all installed.
(right click computer, properties, device manager then use driver pack to install uninstalled drivers same
with windows 7)
a. Off firewall
b. Set time zone to ___
c. Set date and time
d. Change computer name if required
e. Install browser (Firefox/chrome) and MS office

ROUTER CONFIGURATION
a. Set the static IP Address of the server pc
-click set IP add DNS server automatically by clicking on the network icon on the right side of
the task bar, then select network and sharing, properties…….
Ex. IP Address: 192.168.0. 100
Subnet mask: 255.255.255.0
Default gateway: 192.168.0.1 router ip address
Preferred DNS: 192.168.0.1 same with default gateway

Note: do the same with Access Point. After you configured AP, off or remove connection.

SETTING UP STATIC IP ADDRESS ON SERVER


-set the IP address by default
-open cmd, then type ipconfig then copy the IPv4 address (192.168.0.100), then use it as your IP Address
and change the 3rd octet w/ your number
ex. IP address: 192.168.2.100
subnet: 255.255.255.0
default; 192.168.0.1
preferred DNS: 192.168.0.1
INSTALL PRIMARY DOMAIN – Active Directory
FQON: surname.com.ph

INSTALL DHCP
- Validate – write the IP address of the server
- Wins not required
- Scope name: as required ( CSS Lab)
- Starting IP Address- plus 1 to the 4th octet of the server IP Address or as required
- Ending IP Address: as required
- Disable IPv6

CREATE USER – off/disconnect the router


- Click roles
- Active directory user
- Domain name- surname.com.ph
- User – right click- new – user – create – password – never expires

CREATE GROUP POLICY- off/disconnect router


- Select group policy – forest – domain name (surname.com.ph) right click – create new GPO
- Type the name – ex: group 2
- Click the group name you created – under security filtering – click add – advanced – find now – select your
user name – ok

CLIENT PC- CHANGE WORKGROUP TO DOMAIN – on the router- set IP Address to automatically
- Roght click computer – advanced system settings – computer name tab- change – click domain button-
type your domain name (surname.com.ph) –enter your log in user:
Ex: chris@dulfo.com.ph PW: Admin2018

INSTALLING REMOTE DESKTOP


- Require –
- Per user – click your username – click remove – click add- advanced find now- select your user- windows
cannot process- click close- OK- next- install

UNLOCK USER PERMISSION


- Roles- active directory user- domain name(surname.com.ph) - click user- right click username- remote
control tab- uncheck user’s permissions- apply- OK

CLIENT REMOTE CONFIGURATION- check the IPv4 IP Address


- Right click computer- properties- advanced system settings- remote tab- select users- add- advanced- find
now- select user you created- OK- click the button allow (less secure)

REMOTING CLIENT
- Start- accessories- remote desktop connection

You might also like