Republic of the Philippines

Department of Education
Regional Office IX, Zamboanga Peninsula

9 Zest for Progress

Z Peal of artnership

TLE/TVL
Computer Systems
S 3-Module
Quarter i i 1
Using Hand Tools: Plan and Prepare for Tasks
to be Undertaken

Name of Learner: ________________________

Grade & Section: ________________________
Name of School : ________________________

1
TVL-ICT Grade 9 Computer Systems Servicing
Alternative Delivery Mode
Quarter 3 – Module 1 - Using Hand Tools: Plan and Prepare for tasks
to be undertaken
First Edition, 2020

Republic Act 8293, section 176 states that: No copyright shall

subsist in any work of the Government of the Philippines. However, prior
approval of the government agency or office wherein the work is created
shall be necessary for exploitation of such work for profit. Such agency or
office may, among other things, impose as a condition the payment of
royalties.

Borrowed materials (i.e., songs, stories, poems, pictures, photos,

brand names, trademarks, etc.) included in this module are owned by
their respective copyright holders. Every effort has been exerted to locate
and seek permission to use these materials from their respective
copyright owners. The publisher and authors do not represent nor claim
ownership over them.

Published by the Department of Education

Secretary: Leonor Magtolis Briones
Undersecretary: Diosdado M. San Antonio

Development Team of the Module

Writer: Hazel P. Bacasmo

Reviewer’s Name: Evelyn C. Labad EdD, Nilda Y. Galaura EdD

Editor: James L. Colaljo MAEM

Illustrators: Vincent Hersel E. Murcia

Joevic R. Pasilan

Layout Artists: Vincent Hersel E. Murcia

Joevic R. Pasilan

Management Team: SDS: Ma. Liza R. Tabilon EdD, CESO V

ASDS: Judith V. Romaguera EdD
OIC-ASDS: Ma. Judelyn J. Ramos EdD
OIC-ASDS: Armando P. Gumapon EdD
CID Chief: Lilia E. AbelloEdD
LR : Evelyn C. Labad EdD
PSDS: Ma. Theresa M. Imperial EdD
Principal: Nilda Y. Galaura EdD

Printed in the Philippines by ________________________________

Department of Education – Region IX
Office Address: ____________________________________________
Telefax: ____________________________________________
E-mail Address: ____________________________________________

2
 What I Need to Know

This module is a one-lesson module. It covers key concepts

planning and preparing tasks to be undertaken in using hand tools.

In this lesson you will learn to:

• Identify steps on how to prepare tasks when using hand tools;
• Select appropriate hand tool required in a specific task;
• Design a plan on task preparation in using hand tools.

PREPARING TASK AND

Lesson 1 IDENTIFYING HAND TOOLS

What’s In

ACTIVITY 1
Directions: Read the questions carefully and encircle the letter of the
correct answer.

1. After using different technical drawing tools, what should be done

next?
a. Store it in the proper place.
b. Leave it as it is.
c. Call for somebody to keep it.
d. Wait for someone to tell you so.

2. Why is it important to keep things in place?

a. For ease of finding
b. To easily locate it again
c. To avoid danger
d. All of them

3. Who is responsible of keeping and storing things in the right place?

a. The supervisor
b. The janitor
c. The user
d. Others

3
 4. It is a tool used to tighten screws.
a. Screwdriver
b. Wire cutter
c. Crimping tool
d. Tweezer

5. A tool used to cut wires.

a. Needle-Nose plier
b. Scissors
c. Knife
d. Wire cutter

What’s New

ACTIVITY 2

Have you experience using hand tools? If yes, have you ever committed a
mistake when using them?
Directions: Write your answer in a paragraph form.

You will be rated using the rubrics below.

Content 60%

Grammar 20%

Correct use of punctuation marks 10%

Legibility 10%

ACTIVITY 3

Directions: Read and do the activity below.

1. Make a plan that will safely achieve the tasks below.
Task 1: Opening a Computer Case
Task 2: Cleaning a Computer keyboard
4
 2. All students whose family names start with a vowel letter will
stick on task 1, while those students whose family names start
with consonant letter will focus on task 2.
3. Then, based on the task assigned, make a table using the
format below.Make a plan on how are you going to perform the
task and identify the possible impacts it can give to you and to
the environment. You may write as many as you can.
4. Example is provided in the second row of the table

TASK: (Write here your task name.)

Steps to be done Impact to yourself

(ex. Read the user’s Manual) (ex. Protect me from bruises)

1.

2.

3.

4.

What is It

A tool is a handheld device that aids in accomplishing a task.

Tools ranges from traditional metal cutting part of a machine to an
element of a computer program that activates and controls a particular
function.

How to prepare task when using hand tools?

5
 The following are the things to be considered when preparing a
task when using Hand tools.

1. How do you select the first tool to for the job?

• First, know and understand in detail the scope of work to be
accomplished.
• Second, plan for the scope taking into account the sequence of
tasks.
2. Select the best tool for each task requires training use of tools,
experience in safe use and following manufacturer’s guidance and
instructions for a particular tool.
3. When obtaining the tool, all the associated tooling and consumable
parts, as recommended by the manufacturer, must be included. In
addition, related consumable parts must also be selected and in
accordance to manufacturer’s instruction.

So before touching on the job, you have to be familiar and very well
oriented on the task that you are about to do. Do not start your job
without understanding the task completely. Then whatever instruction is
being stated in the manufacture’s manual regarding the use of the tool,
you need have to follow it not just to achieve the goal but most
importantly for your safety.

Hand Tools

A hand tool is a device for performing work on a material or a

physical system using only hands. The hand tools can be manually
used employing force, or electrically powered, using electrical current.
Examples of Hand Tools:

Flat head screwdriver – used to loosen or tighten

slottedscrews.

Philips head screwdriver – used to loosen or tighten

cross-head screws.

6
 Torx screwdriver - used to loosen or tighten screws
that have a star-like depression on the top, a feature
that is mainly found on laptop.

Hex driver – sometimes called a nut driver, is used to

tighten nuts in the same way that a screwdriver
tightens screws.

Needle-nose plier – used to hold small parts.

Wire cutter – used to strip and cut wires.

Tweezers – used to manipulate small parts.

Part retriever – used to retrieve parts from location that

aretoo small for your hand tofit.

Flashlight – used to light up areas that you cannot see

well.

7
 Crimper – is a devise used to conjoin two pieces of metal
by deforming one or both of them in a way that causes
them to hold each other.

Network cables and phone cables are created using a

crimping tool (shown below) to join the RJ-45 and RJ-
11 connectors to both ends of either phone or Cat
5 cable.(computerhope.com)

What’s More

ACTIVITY 4

Directions: Make a plan on the preparation for cleaning computer

system unit inner part. The plan should be inorder. Number 1 should
contain the first step of your plan, and then followed by 2nd step and so
on and so forth. There will be no minimum number of steps as long as
your plan will be complete and in detailed.

ACTIVITY 5

Directions: Rank the steps below on how to prepare task. Rank 1 as the
first step and 5 as the last.

______ Read and follow the manufacturer’s manual for instruction and
guidance on how to use the tool.

______ Get oriented on what to do.

______ Choose the best tool and equipment to be used in doing the task.

______ Prepare for the things needed to accomplish the task.

______ If unsure on how to use the tool, refer to user’s manual.

8
ACTIVITY 6

Directions: Below you will find images of the different hand tools. Identify
the name of the tools enumerated.

Images of hand tools Name of the tool

What I Have Learned

ACTIVITY 7

Directions: Fill in the blanks with the corresponding correct word to

complete the paragraph.

In using hand tools, it is essential to know and be oriented with

ways and means of planning and preparing a task. Using hand tools if
not planned and prepared may lead to unwanted results. In order to
avoid those things to happen, a set of things to be considered when
9
preparing a task when using Hand tools need to be observed. These
include the proper (1) _________ of the tool for the task, the (2) _________
use of the selected tool, and by following what the manufacturer of the
tool has specified in the manufacturer’s instruction. (3) _______ tools are
operated using either human hand force, or electrical power. The
(4) ____________ are used to loosen or tighten
(5) _________. (6)__________________is used to loosen or tighten slotted
screws. A (7)___________ screwdriver is used to tighten or loosen cross-
head screwdriver. A torx screwdriver is used to work with star-like
depression on the top, which is commonly used on (8)____________. A hex
driver is used to tighten (9) ________. Needle nose plier,
(10) ____________ and part retriever are used to hold and manipulate
small parts which is impossible for a human man to hold. Also, crimper
and flashlight are considered as hand tool.

What I Can Do

ACTIVITY 8

Directions: Read the scenario below and do the task.

Scenario: Your system CPU fan makes a noise when the computer is
turned on. And you wanted to open the case to check what it is. How will
you do it?

Task: Think of one possible solution to the problem and make a plan on
how you are going to solve the issue in a table form. Number 1 should
contain the first step of your plan, and then followed by the 2nd step,
and so on and so forth. You can write as many as you can.

NEEDED TOOL OR
STEPS TO BE DONE
RESOURCES

10
 Assessment

TEST I
Directions:
Read and understand each question carefully and encircle the letter of
the correct answer.

1. It is a handheld device that aids in accomplishing a task.

a. Tool

11
 b. Machine
c. Robots
d. Equipment

2. What is appropriate to do if you are not familiar on how to use a tool?

a. Experiment on the tool.
b. Take the risk in using the tool.
c. Ask for Professional Help.
d. Just do nothing to prevent harm.

3. What will you do before using a tool?

a. Know the job to be done.
b. Look for the appropriate tool.
c. Prepare for safety measures.
d. Study the use of tool.

4. In performing a task, which of the following must come first?

a. Select tool for the task.
b. Plan for the task.
c. Seek Assistance to accomplish the task.
d. Buy tools for the task.

5. Who will be responsible in any failure or harm when using a tool?

a. Manufacturer
b. Yourself
c. Your parents
d. Your colleagues

TEST II
Directions: Read each statement carefully and write T if the statement
is TRUE and F is the statement is FALSE.Write your
answers in your Activity Notebook

1. In planning and preparing for tasks when using hand tools, aside from
personal safety, environmental safety should also be considered.

2. All tools available in the market come with exact and detailed manual.

3. Consumable parts of a tool must be included upon purchase of the

tool.

4. There is a right tool for a particular job.

5. Misused of tools may lead to danger.

12
 Key Answers

ACITIVITY 1 ACITIVITY 2 ACITIVITY 3 ACITIVITY 4

Answers Vary Answers Vary Answers Vary

ACTIVITY ACTIVITY 6 ACTIVITY ACTIVITY ASSESSMENT

5 7 8

Answers
Vary

REFERENCE:

1. K TO 12 Basic Education Curriculum Technology and Livelihood

Education Learning Module by Ronaldo V. Ramilo, Deover M.
Pasco, et.al.

13
14