Content Standards: LO 3. Set Router/wi-Fi/wireless Access Point/repeater Configuration
Content Standards: LO 3. Set Router/wi-Fi/wireless Access Point/repeater Configuration
In this lesson, you will be able to identify wireless settings, enumerate steps in
Configuring Wireless Settings, identify what Firewall with Advanced Security and
enumerate steps in Configuring Firewall with Advanced Security.
PRETEST
Rearrange the given steps on how to configure WAN. Put the correct sequence of steps
by using numbers 1-10 in the space provided, 1 is the First Step and 10 is the Last
Step.
1. Change the default user name and password
5. Select the Start button, look for Control Panel and click
Unlocking of Terms
SETTING-UP ROUTER
The Router’s LEDs are located on the front panel (View from the left to right).
Note: after a device is successfully added to the network by WPS function, the WPS LED will
keep on for about 5 minutes and then turn off.
The following parts are located on the rear panel (view from left to right)
INTERNET: This INTERNET port is where you will connect the DSL/cable Modem.
4,3,2,1 (LAN): These ports (4,3,2,1) connect the Router to the local PC(s).
POWER: The Power socket is where you will connect the power adapter. Please use
the power adapter provided with this TL-WR840N 300Mbps Wireless N Router.
System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the
Router is connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
Installation Environment Requirements
Place the Router in a well-ventilated place far from any heater or heating vent
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: 0°C`40°C (32°F`104°F)
Operating Humidity: 10%`90%RH, Non-condensing
Introduction
A router is a box that allows multiple computers, smartphones, and so on to join the same
network. From there, the router is typically connected to a modem in order to provide an Internet
connection to any device that is connected to the router. This guide aims to help you through
the first time setup process for your router.
1 Connect Power
1. Locate the power cable and connect it to a power source like an outlet or surge
protector.
2. Plug the other end of the power cable to the router's power input, which is typically
located in the rear.
Your router must be connected to a modem in order to provide the local network with an Internet
connection.
3. Take one end of the cable and plug it into an available Ethernet (or LAN) port on the
rear of your modem. These ports are typically yellow.
4. Usually this is all that is needed to connect your router to a wired connection.
3 Log in
1. Using a computer that is connected to the TP-Link router, open a web browser (such as
Safari, Google Chrome or Internet Explorer).
2. At the top of the browser is the address bar, type in http://tplinkwifi.net.
3. If the address does not work, check the bottom of the router to confirm the default
access address. You can also try to connect via IP
address (example: http://192.168.1.1 or http://10.0.0.1)
Username: admin
Password: admin
4 Select Password
Wherever possible, you should pick a password that is impossible to guess and is also resistant
to brute-force attacks.
5 Change SSID and Password
After logging-in the router's user interface:
1. Click on Wireless
2.4 then Wireless Settings.
2. Confirm or change
the Network Name. The
network name (or SSID) is the
name others will see when
searching for available
wireless networks in the area.
3. Next, click on Wireless Security and type your new password. Scroll down and
click Save.
4. 4. For Ve
r sion, select WPA2-PSK.
One some models you must select the Security and then the Version. Choose WPA/WPA2 -
Personal and WPA2-PSK.
5. Enter the password you have chosen in the box next to Password.
7. Your wireless security settings have now been updated and your devices may connect
to it.
Any time you change your wireless security settings you will need to reconnect your
wireless devices.
If your router is dual-band, meaning it has a 2.4 and a 5 GHz network you may need to
repeat the steps listed above for each network because each network may be controlled
individually. You must use different network names for each band.
If your router has a guest network you will need to repeat the steps listed above for the
guest network because it is controlled separately.
Best Practices:
Do not use a master password that you use everywhere (such as email, work, school,
home, network)
If possible, do not share your password with anybody.
Passwords that are shared with others, like for a home network, should only be shared if
necessary.
Be aware when typing your password in public, or that in no way anyone is watching.
Some types of electronic devices like computers and smartphones can remember
passwords, so beware of devices that are not yours.
Make a schedule of when to change your password. For example, every 180 days.
It is not recommended to write down passwords. But if you have to, make sure that it is
neither physically nor visually accessible by others.
7 Deciding to update
Router updates are provided to add new security features, fix vulnerabilities, or other
enhancements like performance upgrades. We recommend updating your router at this time in
order to get the best possible security. Depending on the model, you may need an internet
connection, access to a computer, and a formatted USB flash drive in order to update.