TLE-ICT-CSS-G9-Q4 TEC-Week1-4

Bs criminology (Arellano University)

Scan to open on Studocu

Studocu is not sponsored or endorsed by any college or university

Downloaded by Airelle Soler (airellesoler@gmail.com)
9

TLE – ICT – CSS

Quarter 4 – Module 1-4:
Testing Electronic Components

Downloaded by Airelle Soler (airellesoler@gmail.com)

TLE- ICT – CSS - Grade 9
Alternative Delivery Mode
Quarter 4 – Module 1-4: Testing Electronic Components
First Edition, 2020

Republic Act 8293, section 176 states that: No copyright shall subsist in any
work of the Government of the Philippines. However, prior approval of the government
agency or office wherein the work is created shall be necessary for exploitation of such work
for profit. Such agency or office may, among other things, impose as a condition the payment
of royalties.

Borrowed materials (i.e., songs, stories, poems, pictures, photos, brand names,
trademarks, etc.) included in this module are owned by their respective copyright holders.
Every effort has been exerted to locate and seek permission to use these materials from their
respective copyright owners. The publisher and authors do not represent nor claim ownership
over them.

Published by the Department of Education Secretary:

Leonor Magtolis Briones Undersecretary: Diosdado M.
San Antonio

Development Team of the Module

Writers: Ericson B. Elnar
Editors: Reynald Manzano, Ruth Marie B. Eltanal Reviewers:
Mark Dave M. Vendiola, Jesusa D. Paladar Typesetter: Ericson
B. Elnar
Layout Artist: Ericson B. Elnar
Management Team: Senen Priscillo P. Paulin, CESO V Rosela R. Abiera
Joelyza M. Arcilla EdD Maricel S. Rasid
Marcelo K. Palispis EdD Elmar L. Cabrera
Nilita L. Ragay EdD
Antonio B. Baguio, Jr. EdD

Printed in the Philippines by

Department of Education –Region VII Schools Division of Negros Oriental

Office Address: Kagawasan, Ave., Daro, Dumaguete City, Negros Oriental Tele
#: (035) 225 2376 / 541 1117
E-mail Address: negros.oriental@deped.gov.ph

Downloaded by Airelle Soler (airellesoler@gmail.com)

 9

TLE – ICT – CSS

Quarter 4 – Module 1-4:

Testing Electronic Components

Downloaded by Airelle Soler (airellesoler@gmail.com)

 What I Need to Know

This module was designed and written with you in mind. It is here to
help you master how to input data into computer. The scope of this module
permits it to be used in many different learning situations. The language used
recognizes the diverse vocabulary level of students. The lessons are arranged
to follow the standard sequence of the course. But the order in which you
read them can be changed to correspond with the textbook you are now using.

The module contains only one lesson:

 Lesson 1 – Determine Criteria and Plan an Approach for Testing
Electronic Components

After going through this module, you are expected to:

1. identify the parts of an analogue multi tester;
2. measure some electronic components; and
3. practice safety while measuring electronic components.

Downloaded by Airelle Soler (airellesoler@gmail.com)

 What I Know

Direction: Identify the word or phrase being described in the sentence. Write your
answers in your notebook.

1. It is an electronic measuring instrument that combines several

measurement functions in one unit.
2. These are used to connect to whatever device you're planning on
testing and measuring.
3. This is a small knob usually located near the dial that is labeled
"Ohms Adjust," "0 Adj," or something similar.
4. This allows you to change the function between volts, ohms,
and amps, and to change the scale of the meter.
5. This has the arc-shaped scales visible through the window and a
pointer which will indicate the values read from the scale.
6. In a multimeter, at what position does the needle of pointer be
located if the test leads are not in contact with anything.
7. What are you going to measure in order to determine whether or
not the circuit is Alternating Current or Direct Current?
8. In a multimeter, what color of the test probe is associated with
positive charge?
9. What is the meaning of VOM?
10. In a multimeter, at what position does the needle of pointer be
located if the test leads are in contact with anything.

Note: If you get 100% correct in this pre- assessment, skip the lesson but if
not and only get 50% to 99% correct, then proceed with the lesson.

Downloaded by Airelle Soler (airellesoler@gmail.com)

 Lesson Determine Criteria and Plan
1 an Approach for Testing
Components

What’s In

In this lesson, you will learn what tool to be used in testing electronic
components. Also, how to use this tool, in the proper way in testing the electronic
components.

What’s New

In order to test some basic electronics components, one must use a multimeter
either analogue or digital.

Identify the parts of the analogue tester by choosing from the words inside the
box. Write your answers in your notebook.
Scale Range Selector Positive Probe Test Probes
Dial/Infinity Knob Range Needle/Pointer

Zero Ohm Adjuster Negative Probe Ports

Downloaded by Airelle Soler (airellesoler@gmail.com)

 What is It

A multimeter or a multi-tester, also known as a volt/ohm meter or VOM, is

an electronic measuring instrument that combines several measurement functions
in one unit. A typical multimeter may include features such as the ability to
measure voltage, current and resistance. Multimeters may use analog or digital
circuits4 analog multimeters and digital multimeters (often abbreviated DMM or
DVOM.)

Initial Steps in Using Analog Multi‐tester

1. Locate the dial of your multimeter. This has the arc-

shaped scales visible through the window and a pointer which
will indicate the values read from the scale.

2. Find the selector switch, or knob. This allows you to change

the function between volts, ohms, and amps, and to change the
scale (x1, x10, etc.) of the meter.

3. Locate the openings in the case where you'll insert the

test leads. Most multimeters have several jacks used for this
purpose.

4. Locate the test leads. There should be two test leads or

probes. Generally, one is black and the other red. These are
used to connect to whatever device you're planning on testing
and measuring.

5. Find the battery and fuse compartment. This is usually

found on the back but is also sometimes on the side of some
models. This holds the fuse (and possibly a spare), and the
battery that supplies power to the meter for resistance tests.

6. Find the Zero Adjustment knob. This is a small knob

usually located near the dial that is labeled "Ohms Adjust," "0
Adj," or something similar. This is used only in the ohms or
resistance range, while the probes are shorted together
(touching each other).

Downloaded by Airelle Soler (airellesoler@gmail.com)

Measuring Resistance

1. Set the multimeter to Ohms or Resistance. Turn the

meter on if it has a separate power switch. When multimeter
measures resistance in ohms, it cannot measure continuity
because resistance and continuity are opposites. When there
is little resistance, there will be a great deal of continuity, and
vice versa.

2. Observe the meter indication. If the test leads are not in

contact with anything, the needle or pointer of an analog meter
will rest at the left-most position. This represents an infinite
amount of resistance, or an "open circuit." It's safe to say there
is the no continuity, or path between the black and red probes.

3. Connect the test leads. Connect the black test lead to the
jack marked "Common" or "-". Then, connect the red test lead
to the jack marked with the Omega (Ohm symbol) or letter "R"
near it.

4. Hold the probes at the end of the test leads together.

The meter pointer should move fully to the right. Locate the
"Zero Adjust" knob and rotate it so that the meter indicates
"0" (or as close to "0" as possible).

5. Measure the resistance of something like a light bulb that

you know is good. Locate the two electrical contact points of
the bulb. They will be the threaded base and the center of the
bottom of the base.

6. Try different ranges. Change the range of the meter to R x 1.

Zero the meter again for this range and repeat the step above.
Observe how the meter did not go as far to the right as before.

7. Test resistance between hands. Set the meter to the

highest R x value possible and zero the meter.

8. Make sure your reading is accurate. It's very important that

the probes not touch anything other than the device being tested.
A device that has burned out will not show "open" on the meter
when testing if your fingers provide an alternate path around the
device, like when they are touching the probes.

Downloaded by Airelle Soler (airellesoler@gmail.com)

Measuring Voltage

1. Set the meter for the highest range provided for AC

Volts. Many times, the voltage to be measured has a value that
is unknown. For this reason, the highest range possible is
selected so that the meter circuitry and movement will not be
damaged by voltage greater than expected.

2. Insert your test probes. Insert the black probe in the "COM"
or "-" jack. Next, insert the red probe in the "V" or "+" jack.

3. Locate the voltage scales. There may be several Volt scales

with different maximum values. The range chosen by the selector
knob determines which voltage scale to read.

Measuring Amperes

1. Make sure you've measured the voltage first. You need to

determine whether or not the circuit is AC or DC by measuring
the voltage of the circuit as described in previous steps.

2. Set the meter to the highest AC or DC Amp range

supported. If the circuit to be tested is AC but the meter will only
measure DC amps (or vice versa), stop. The meter must be able
to measure the same mode (AC or DC) amps as the voltage in the
circuit, otherwise it will indicate 0.

What’s More

Direction: Unscramble the letters below to form significant words learned in this
lesson. Write your answers in your notebook.

1. SPAMERE
2. STORESIR
3. EGLOVAT
4. LOGANA
5. TERSET

Downloaded by Airelle Soler (airellesoler@gmail.com)

 What I Have Learned

Direction: Answer the K-W-L chart. Write your answer on your notebook.

K W L
What do you think What do you WANT to What did you LEARN
you KNOW about know about Steps in about Steps in Using
Steps in Using Using Multimeter? Multimeter?
Multimeter?

What I Can Do

Direction: In your notebook, copy and complete the diagram below to show the
correct process in measuring resistance.
Measuring Resistance

Assessment

A. Direction: Identify the word or phrase being described in the sentence. Write your
answers on your notebook.
1. It is an electronic measuring instrument that combines several
measurement functions in one unit.

Downloaded by Airelle Soler (airellesoler@gmail.com)

 2. These are used to connect to whatever device you're planning on
testing and measuring.
3. This is a small knob usually located near the dial that is labeled
"Ohms Adjust," "0 Adj," or something similar.
4. This allows you to change the function between volts, ohms,
and amps, and to change the scale of the meter.
5. This has the arc-shaped scales visible through the window and a
pointer which will indicate the values read from the scale.
6. In a multimeter, at what position does the needle of pointer be
located if the test leads are not in contact with anything.
7. What are you going to measure in order to determine whether or
not the circuit is Alternating Current or Direct Current?
8. In a multimeter, what color of the test probe is associated with
positive charge.
9. What is the meaning of VOM?
10. In a multimeter, at what position does the needle of pointer be
located if the test leads are in contact with anything.

B. Direction: Choose from any of the following activities and make a flowchart of
it. Do this on your notebook.
1. Steps in measuring voltage.

2. Steps in measuring amperes.

3. Initial Steps in Using Analog Multi‐tester

Additional Activities
Direction: Draw the proper way of measuring resistance using the following material
and equipment. Do this on a piece of short bond paper.
1. Resistor
2. Multimeter

Downloaded by Airelle Soler (airellesoler@gmail.com)

 Answer Key

What I Can Do
Answers may vary Multi‐tester
What Have I Learned Analog Using in Steps 3. Initial

3. VOLTAGE
5. TESTER 2. RESISTORS
4. ANALOG 1. AMPERES
What’s More

2. Measuring Amperes
10. Test Probes
9. Positive Probe
8. Negative Probe
7. Probe Ports
6. Range Selector
5. Range
4. Zero Ohm Adjuster
3. Dial/Infinity Knob
2. Scale Measuring Voltage 1.
1. Needle/Pointer B.
What’s New
Right Position 10.
10. Right Position 9. Volt – Ohm Meter
9. Volt – Ohm Meter 8. Red or White
8. Red or White 7. Voltage
7. Voltage 6. Left position
6. Left position 5. Dial
5. Dial 4. Selector Switch
4. S elector Sw itch Zero Adjustment Knob 3.
3. Z ero A djus tment Knob Test Leads 2.
2. Test Leads Multimeter or multi-tester 1.
1.Multimeter or multi-tester A.
What I Know Assessment

Downloaded by Airelle Soler (airellesoler@gmail.com)

Text References

Multimeter. Accessed April 29, 2021.

https://web.ua.es/docivis/magnet/multimeter.html.

<Resistors and Circuits,= n.d. https://learnabout-

electronics.org/Downloads/Resistors-Module-02.pdf .

<Resistor Colour Code and Resistor Tolerances Explained.= Basic Electronics

Tutorials, December 31, 2020. https://www.electronics-
tutorials.ws/resistor/res_2.html.

<How to Test a Capacitor with a Multimeter - ToolBoom.= toolboomcom.

Accessed April 29, 2021. https://toolboom.com/en/articles-and-
video/how-to-test-a-capacitor-with-a-multimeter/.

Technology, Electrical, Anonymous says: Electrical Technology says: Rajender

says: Gethro Parfait says: Suh William says: Kevvy Says: et al. <How to
Check a Capacitor with Digital Multimeter and Analog AVO Meter. By
Four (5) Methods with Pictorial View.= ELECTRICAL TECHNOLOGY, April
28, 2020. https://www.electricaltechnology.org/2013/06/how-to-
check-capacitor-with-digital.html.

Kuhlman, Jesse, and wikiHow. <How to Test a Transformer.= wikiHow.

wikiHow, May 29, 2020. https://www.wikihow.com/Test-a-
Transformer.

Image References
<Testing Electronics Components.= Accessed April 29, 2021.
http://temelelektronik.info/ders/download/componentsaglamlikkontro
lu.pdf.

Kuhlman, Jesse, and wikiHow. <How to Use a Multimeter.= wikiHow. wikiHow,

December 23, 2020. https://www.wikihow.com/Use-a-Multimeter.

<Word Search Puzzle.= Create Your Own Word Search Puzzle | Discovery
Education Puzzlemaker. Accessed April 29, 2021.
http://puzzlemaker.discoveryeducation.com/WordSearchSetupForm.as
p.

<Resistors.= McGraw-Hill Companies, 2007.

https://www.oakton.edu/user/1/agero/ELT101/Presentations/Chapte
r02.pdf.

10

Downloaded by Airelle Soler (airellesoler@gmail.com)

For inquiries or feedback, please write or call:

Department of Education – Schools Division of Negros Oriental

Kagawasan, Avenue, Daro, Dumaguete City, Negros Oriental

Tel #: (035) 225 2376 / 541 1117

Email Address: negros.oriental@deped.gov.ph Website:
lrmds.depednodis.net

11

Downloaded by Airelle Soler (airellesoler@gmail.com)